What did you do to your truck today? Chapter II

[BugzC10]

Originally Posted by hewittca

This happened last night, but still less than 24 hrs ago so it counts right? I Completed the last step of my shortbed conversion by getting the bed put back on for the last time and bringing the truck home after being at my dad's house off and on for the last few months. Here is a before and after from the day I got it in March '16 to yesterday.

I see your son is ready to take possession...

[mud.man.rj]

Short bed and rims make such a huge difference for the good, nice work.
Mudman.

[pryorstemmed]

I put back in a reproduction egg crate grill. Looks a lot better than the aftermarket it had. I just have to figure out the plastic clips...they don't want to snap into the inner chrome grille surround.

[FRCvette]

Finished up Retro Sound 2 radio install over the weekend and installed Juliano's three point seat belts today.

[ghalperin]

Went for my first road test since my frame off.

[mud.man.rj]

Sooo how was the 1st run in the truck, bet it was nice to get out in it again.
Mudman.

[ghalperin]

Originally Posted by mud.man.rj

Sooo how was the 1st run in the truck, bet it was nice to get out in it again.
Mudman.

I was so stoked to get it back on the road. I last drove it 44 days ago.

I upgraded so many systems. The power steering was great. The disk brakes acted as they should. The lowered height, with Bilsteins and sway bars made it handle really well. The full syncro trans (still on the column) was nice to use. The 2:76 rear end was such an improvement over the 4:11s that were in it. Although it kicked my butt twice, the Centerforce clutch works perfect. Last but not least, the 396 runs really well. I fried the tires a couple of times. It has a lot of power.

I've got a ways to go still.

[Boog]

[QUOTE=ghalperin;7967753]Went for my first road test since my frame off.

Attachment 1661379

As my friend says "that's cool beans right there".
Good looking driver.
Your truck makes me wish I still had the 3ott in mine.

[butler57]

Broke a fan belt on my way back from the hardware store. Had my wife pick me up, quick trip to the auto store, 15 mins to put on a new belt. Gotta love working with old trucks.

[mud.man.rj]

Your sure right on the belt and old classics, try that on any new vehicle, lucky to see where the belt even goes.
Mudman.

[butler57]

Originally Posted by mud.man.rj

Your sure right on the belt and old classics, try that on any new vehicle, lucky to see where the belt even goes.
Mudman.

I'm no mechanic but I really do enjoy puttering around and fixing things up. I love how easy these trucks are to work on and I really enjoy all the help I've received on this site.

[In The Ten Ring]

Yesterday I got my original 4 row (lower) radiator brackets sand blasted. A friend from jr. high I haven't seen since 1998 did that for me at this shop. Great seeing him again and getting that done.

[creekncabin]

Replaced the old "3 Wire" Alternator with a new "1 Wire" Alternator.
Quick and painless....

[mike16]

I installed two valve cover gaskets, a fuel pump and some new fuel hoses and an inline filter,

I got rust in the tank problems.

Discovered a vaccuum line leak between the carb and the vaccuum advance.

[In The Ten Ring]

I got a little something done yesterday (posting at 2 AM). I put NAPA Rust Treatment onto my lower radiator brackets as a primer.

[B Myers]

Originally Posted by creekncabin

Replaced the old "3 Wire" Alternator with a new "1 Wire" Alternator.
Quick and painless....

I did the same when I restored my '71, found out the original wiring could not carry the robust charging capability of the one-wire alternator. The factory fuse link or if you replace it with an inline fuse may not handle the potential 60 amps or so that it can generate so I added into the harness a 10 guage wire direct from the alternator to the battery. Great add though for these old trucks even though it knocks out the generator guage function. May deal with a voltage guage in it's place at a later date.

[70cst]

I brought my truck home ...

[mike16]

gave my front end a lube job

noticed that my disc brake pads need replacing

tommarrow i'm going to flush my cooling system

[In The Ten Ring]

Yesterday I got my 4 row lower radiator brackets painted. That should do it for front-end reassembly preparations.

[chewychevy67]

I added a tailgate lock.

[Towbiz]

Picked up my freshly upholstered buddy seat , dug out tach dash . Now to install tilt column & power steering . Soon !

[re1]

Originally Posted by Towbiz

Picked up my freshly upholstered buddy seat , dug out tach dash . Now to install tilt column & power steering . Soon !

Any Pictures ?

[ghalperin]

I went to Donut Derelect's and then Home Depot.

[66clow]

[QUOTE=ghalperin;7969613]I went to Donut Derelect's

Left LA in January, miss that get together. Awsome looking tuck!

Went to pick up some yummy southern barbeque for fathers day. But usually run into this traffic on the weekend in the middle of the day. Joys and pain of living on the beach, but who is complaining, I moved here from LA. This is nothing. Did a little work Saturday on the roof surface rust repair. Also went to a car show but just saw a bunch of new mustangs and corvettes. Not much of a show, passed a bunch of those on the way there. Lol Happy Fathers Day all!

[Possmguts]

Took the bed back off the frame and took it apart and put the new sides on and sat it back on the frame today. Will finish mocking it all up tomorrow...