![]() |
|
![]() |
#1 |
Registered User
Join Date: Jun 2008
Location: South Florida
Posts: 11,375
|
Re: What did you do to your truck today!
Instlled my billet hood hinges..
__________________
Get your facts first, and then you can distort them as much as you please!!!!!. Sylvester's build thread >>>http://67-72chevytrucks.com/vboard/s...ht=big+rebuild |
![]() |
![]() |
#2 |
RAT1968 '68 Cab/'71 Parts
Join Date: Feb 2002
Location: Coarsegold, CA
Posts: 2,375
|
Re: What did you do to your truck today!
Ordered a Street Demon 1901 (Polymer center), went to the auto parts store to try to sort out the gas cap issue. Removed a little fluid from the Master Cyl rez. while trying to sort out the cap/gasket leak. Climbed under and made a heat shield between the new pass side pipe and the fuel line under the cab. Sorta figured out that the trans fluid ooze was coming from the trans dip stick. I have another one that isn't as "fancy". Like fancy women (no offense, Ladies), most of the time the ones that are built more sturdily work better in the long run. I'll change out the filler "tube" next time I can deal with going under....
Installed the trim around that already installed home-made headliner. Plopped a center console in....I think [I] got his one ten years ago off the shelf at Pep Boys. It's only 2:10 in the afternoon. I'm glad to have her home, but that's all I can do today. I'm old.
__________________
M17 Coarsegold, CA RAT's shiny now. But always a rat. Last edited by magwakeenercew2jh; 09-18-2012 at 05:31 PM. |
![]() |
![]() |
#3 |
Registered User
Join Date: Nov 2010
Location: Grand Terrace, Ca.
Posts: 1,607
|
Re: What did you do to your truck today!
|
![]() |
![]() |
#4 |
Registered User
Join Date: Jun 2012
Location: Pittsgrove, NJ
Posts: 1,502
|
Re: What did you do to your truck today!
Found out my rear main leak is a rear main and an oil pan leak, my rear shock mounts are shot, my upper coil mount was missing, my trans has no reverse lights ran to it, my new exhaust was ran where my bump stops used to be and apparently I've been driving around for four months with no pilot bearing. On the upside it's Saturday
![]() Posted via Mobile Device Posted via Mobile Device
__________________
Will 1968 C10 - Project Texa Go 6.0/4L80e 2003 Mitsubishi Lancer Evolution 2002 Ford Excursion 7.3L 2024 Toyota Sienna |
![]() |
![]() |
#5 |
Registered User
Join Date: Feb 2012
Location: So. Cali.
Posts: 2,643
|
![]()
Typical Summer in La La Land ;
It's been over 100° F so instead of driving my air conditioned Mercedes , I've been driving my '69 C/10 . it starts right up and goes just fine in the blistering heat , but of course ! it's an 42 year old unrestored CHEVROLET ![]()
__________________
-Nate Geezer '49 3100 235 W/ Muncie SM420 SOLD '69 C/10 shortbed sidemount survivor 250 L6 W/ 350TH ![]() |
![]() |
![]() |
#6 | |
RAT1968 '68 Cab/'71 Parts
Join Date: Feb 2002
Location: Coarsegold, CA
Posts: 2,375
|
Re: What did you do to your truck today!
Quote:
__________________
M17 Coarsegold, CA RAT's shiny now. But always a rat. |
|
![]() |
![]() |
#7 |
Registered User
Join Date: Sep 2005
Location: Kansas
Posts: 774
|
Re: What did you do to your truck today!
Drove it up to a weekly Friday night car show
![]() ![]()
__________________
1972 C10 LWB- 4.5 Front and 5 Rear Drop, 406/TH350 1966 Caprice 1968 Impala (Frame Off LSX Project) 2001 Tahoe LT 2013 Hyundai Elantra 2010 Kawasaki Z1000 |
![]() |
![]() |
#8 |
Suppose to be workin........
![]() Join Date: Jul 2001
Location: Shawnee, KS USA
Posts: 164
|
Re: What did you do to your truck today!
Started the engine swap...got the old one out!!
![]() ![]() ![]() ![]() ![]() Think there was a small oil leak.....somewhere..... Stay tuned
__________________
Brent '68 C10 '70 C10 '72 LeMans "03 Trailblazer "Stupidity is like a skill, some are born with it and some develop it over a period of time."" Author unknown ![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Nov 2011
Location: Sheffield, ALA
Posts: 2,471
|
Re: What did you do to your truck today!
Put her back in the shop after having a ruff weekend. Had to carry the wife to hospital Thursday,she had some medication that caused problems.the truck had to spend the nite in the parking lot whick I didn't like to well, brought her home Saturday morning then she got treated to a nite on the town.we all loved it.
I've got to clean it up for a show I'm doing this weekend.She is going to show off a little.haha. wish me well fellows there will be about 20 in this groupif it's like last year. |
![]() |
![]() |
#10 |
RAT1968 '68 Cab/'71 Parts
Join Date: Feb 2002
Location: Coarsegold, CA
Posts: 2,375
|
Re: What did you do to your truck today!
I'd say you already won...Glad she's okay.
__________________
M17 Coarsegold, CA RAT's shiny now. But always a rat. |
![]() |
![]() |
#11 |
Registered User
Join Date: Nov 2011
Location: Sheffield, ALA
Posts: 2,471
|
Re: What did you do to your truck today!
|
![]() |
![]() |
#12 |
Grand PooBaa Member
Join Date: Jan 2001
Location: LA, CA
Posts: 5,302
|
Re: What did you do to your truck today!
Wire wheeled the front of the frame and brushed on some POR-15. Still got a ways to go.
|
![]() |
![]() |
#13 |
Registered User
Join Date: Dec 2008
Location: Jackson, MS
Posts: 373
|
Re: What did you do to your truck today!
I started fitting the serpentine belt system to the small block. I like it so far.
![]()
__________________
1968 Chevy C/10 LWB V8 ![]() 1983 K5 Blazer 1989 C1500 Stepside Reg. Cab V8 |
![]() |
![]() |
#14 |
Registered User
Join Date: Oct 2011
Location: Houston, Texas
Posts: 884
|
Re: What did you do to your truck today!
I ordered a WHOLE BUNCH of parts from..*gulp* LMC. It's hard to resist their super user friendly website.
|
![]() |
![]() |
#15 |
Registered User
Join Date: Oct 2011
Location: Houston tx
Posts: 701
|
Re: What did you do to your truck today!
Took my truck to my buddies shop and we are gonna start on building a towhitch for it and may install the cluster I bought a couple of months back ( I hate wiring!!!)
Posted via Mobile Device |
![]() |
![]() |
#16 |
Registered User
Join Date: Jun 2012
Location: Givors - FRANCE
Posts: 109
|
Re: What did you do to your truck today!
ordered some parts :
new red carpet to change the old black (which is brown now) red plug and chug cup older custom autosound radio some gifts/apparels we can't find in france : vintage chevy cap, long leaves t-shirtwaiting for receiving now !
__________________
'70 C10 shortbed - 350 Edelbrock equipped - 4/1 headers - 3" flowmaster exausts '07 MUSTANG V8 convertible - CAI Spectre - Brembo's - 3" flowmaster exhausts |
![]() |
![]() |
#17 |
Registered User
Join Date: May 2012
Location: Ingersoll, Ontario
Posts: 93
|
Re: What did you do to your truck today!
listed it on kijiji. Not a good day.
|
![]() |
![]() |
#18 |
Registered User
Join Date: Feb 2012
Location: So. Cali.
Posts: 2,643
|
![]()
Installed the Vintage Motor Minder gauge I scored recently and plumbed it in , it works great , now to find a bulb holder so it lights up @ night , in time it'll be part of my lockup TH350C's torque converter control system , I'm adding a green pilot lamp to the setup too so it'll let me know whenever it locks up .
Installed two rope hooks to the backup lamp bolts as I hate drilling holes . Installed an under dash oscillating fan . Swapped the tailgate hooks & chains left for right so underhooking the tailgate is easier , this is an old Farm trick that prevents the hooks from jumping out when you're bouncing down dirt roads . I pulled the spark plugs as it's been missing at idle ~ WOW are they oily ! I wish I'da had my camera as it's hard to belive it ran like this , I guess the bubbas who " rebuilt " this engine just before I bought the truck , screwed it up , I have a spare 292 and may have a line on a takeout 1969 numbers matching 250 , if so I'll overhaul it and stick it in , the work never stops . I'm still not sure which engine I want , the 292's are great but thirsty . In any case , I used my War Surplus Dental Pick to carefully scrape the plugs clean and re - installed them after opening up the gaps to .070" ~ this will drive the HEI to it's full output and maybe stop the plug fouling . It figures I'd install the cab fan the same day the heat wave finally broke ![]()
__________________
-Nate Geezer '49 3100 235 W/ Muncie SM420 SOLD '69 C/10 shortbed sidemount survivor 250 L6 W/ 350TH ![]() |
![]() |
![]() |
#19 |
RAT1968 '68 Cab/'71 Parts
Join Date: Feb 2002
Location: Coarsegold, CA
Posts: 2,375
|
Re: What did you do to your truck today!
It's about the DMV...California style.
The short version: After paying my tags late in July for the period of 9/30/12 to 9/30/13...and them cashing the check on 8/3/12, no tags came. More shortening: At least eight calls later all over the state, with a number of folks hanging up on me (I was ALWAYS NICE...Every time, I had to tell the whole story over to someone new... ...and I thanked them for listening), I got thru to the boss of the boss of the manager at 2:00 today. I usually don't go the "going over your head route". But I was really exasperated. She asked me, "HOW DID YOU GET MY PHONE NUMBER?" Which gave me the chance to throw under the bus a particularly nasty person who said she was mailing my tags to me back on the 10th. Ms. Boss said she'd call me back. I thanked her for any help she could offer. I told her I wasn't a celebrity, I wasn't rich, I wasn't anything but a citizen that already paid the State for something that I'm still not getting, and one to whom promises have been made for way too long....Then I told my wife, "Sure, she'll call me back." At 4:00 I got a call from a woman who said she worked for the Big Boss. She had "cleared" my tags and is mailing them out today. There is some promise here, as she left me her name and phone number and told me she worked for Ms. Big....I think something's gonna happen this time. On another front, I put on the new Street Demon carb. Still working out the linkage, as I had Mickey Moused the last one on the Edlebrock. Very slick install, otherwise. Too hot to finish this afternoon. Can't finish tomorrow...gotta do family stuff. Pics of the finished product on Sat. evening. Here's the notice that came three years ago...I went and got the plates way back then.
__________________
M17 Coarsegold, CA RAT's shiny now. But always a rat. |
![]() |
![]() |
#20 |
Registered User
![]() Join Date: Mar 2012
Location: Okanagan Valley, BC, Canada
Posts: 1,237
|
Re: What did you do to your truck today!
Lowered my truck a little bit today... Getting it ready for bags.
__________________
#teamlongbed "I refuse to go disc brakes. I actually love drum brakes. It makes for an adventure." - 50bomb 1978 Chevy shop truck - static 6/8" 1970 GMC 1500 - Accuair eLevel Resto-mod http://67-72chevytrucks.com/vboard/s...d.php?t=537497 |
![]() |
![]() |
#21 |
Registered User
![]() Join Date: Mar 2012
Location: Okanagan Valley, BC, Canada
Posts: 1,237
|
Re: What did you do to your truck today!
Gotta c-notch the back next week. I like a little bit of rake, but not quite this much.
__________________
#teamlongbed "I refuse to go disc brakes. I actually love drum brakes. It makes for an adventure." - 50bomb 1978 Chevy shop truck - static 6/8" 1970 GMC 1500 - Accuair eLevel Resto-mod http://67-72chevytrucks.com/vboard/s...d.php?t=537497 |
![]() |
![]() |
#22 |
Newbee
Join Date: Jan 2010
Location: Phoenix, Arizona
Posts: 1,406
|
Re: What did you do to your truck today!
Installed crossover steering... man what a difference.
All new ball joints, tie rod ends, steering box. Went from a 4 turn 4x4 box to a 3 turn 2wd box. It steers like an indy car, without the annoying bump steer. |
![]() |
![]() |
#23 |
Registered User
Join Date: Apr 2012
Location: Nashville
Posts: 79
|
Re: What did you do to your truck today!
Spent the weekend with friends who helped do a overhaul on my truck. I brought in the parts (and few runs to the store) and a very good friend from VA drove in with tools and 8 cases of craft beer unavailable in Nashville.
Top end rebuild, new intake, new carb, waterpump, fuel pump, tuneup, new radiator, fan/fan clutch/shroud and distributor rebuild. Font suspension overhaul of brakes, all bushings and ball joints tire rods, ubolts, springs and shocks and rear shocks (the rear springs will have to wait as bolts broke trying to get to them and we ran short on time) We had some issues here and there including some broken head bolts. Don't trust Felpro head bolts everyone. Also LMC Ubolt sizes are wrong. Before http://i.imgur.com/CQKXM.jpg During http://i.imgur.com/1Yo7M.jpg Almost Done http://i.imgur.com/P9aCd.jpg Still have a few things to do but its pretty much done. Just needs a power steering belt and some hose NTP fittings for the heater. |
![]() |
![]() |
#24 |
RAT1968 '68 Cab/'71 Parts
Join Date: Feb 2002
Location: Coarsegold, CA
Posts: 2,375
|
Re: What did you do to your truck today!
Those are *some* friends.
Great to see the before, during, and (almost) after pics. Nice post.
__________________
M17 Coarsegold, CA RAT's shiny now. But always a rat. |
![]() |
![]() |
#25 |
Registered User
Join Date: Apr 2012
Location: Nashville
Posts: 79
|
Re: What did you do to your truck today!
I only have a few, but we would all do anything for each other. Good men indeed.
__________________
______________ Murder Truck - 1967 Short/Stepside C10 5.7 |
![]() |
![]() |
Bookmarks |
|
|