The '67 Burb Build Thread - Page 19 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

67chevy1series · 03-13-2011, 09:47 PM

oh haha well then they didnt weld it properly or somthin like that

*project 67 sub* · 03-13-2011, 10:06 PM

thats even funnier because the welds held just fine, it ripped in right about the middle. still havent went out to take it apart yet, but im sure the u joints are just fine, heck.... i even think the carrier bearing is just fine

67chevy1series · 03-13-2011, 11:48 PM

ok then it really is a mr e

*project 67 sub* · 03-14-2011, 01:12 AM

went out and pulled out the drive shaft, all of the u joints and carrier bearing is fine, will take it in to have the tube replaced on the rear shaft in the morning. hopefully it wont cost me to much $$

*project 67 sub* · 03-14-2011, 02:51 AM

Name: Photo03132345.jpg
Views: 631
Size: 64.4 KB

mmmBoost · 03-14-2011, 02:55 AM

Did it ever hit a cross member or anything with the bags deflated or aired all the way up?

*project 67 sub* · 03-14-2011, 03:23 AM

nope, didn't hit anything till it twisted in half, then it hit the bottom of the rear floor tunnel i had made for drive shaft clearance.

**kev2809** · 03-14-2011, 10:42 AM

thats the first time ive seen something like this. so when you get it replaced...how can you tell if its not gonna happen again? (as in, is there anything preventable to make sure it doesnt snap again?)

*project 67 sub* · 03-14-2011, 02:08 PM

yah me to, i'm taking it to a local drive line guy to have him do the work, will ask him what he thinks, maybe have him put a bigger tube on it or something if that would even make a difference in strength

1sik7t2 · 03-14-2011, 05:13 PM

MY ONLY THOUGHT WOULD BE THE CRACK OR WEAK SPOT ALREADY METIONED OR UR PINION ANGLE IS WAY OFF....MAKIN EXTRA STRESS ON IT

QUOTE=project 67 sub;4551888]yah me to, i'm taking it to a local drive line guy to have him do the work, will ask him what he thinks, maybe have him put a bigger tube on it or something if that would even make a difference in strength[/QUOTE]

*project 67 sub* · 03-15-2011, 12:20 AM

well here is the fix, it cost me $100

, oh well, should be alot stronger now.
Name: Photo03141648.jpg
Views: 615
Size: 85.8 KB

67chevy1series · 03-15-2011, 02:39 AM

kucky at least you have a drive line to fix!

*project 67 sub* · 03-15-2011, 02:56 AM

that isn't even the same rear shaft, that is a completely different one. its been changed from the splined yoke where the carrier bearing presses on all the way to the end. the center u-joint couldn't be reused because the new shaft had a wider joint peace, and then with the new center u-joint, the splined yoke piece had to be changed because the new u-joint didn't fit right in the old one

*project 67 sub* · 03-15-2011, 04:51 PM

few more pics from the cruise

me cruising next to leddzepp
Name: CPP Truck Show 021.jpg
Views: 607
Size: 54.3 KB

look in the mirror on this one lol.
Name: CPP Truck Show 026.jpg
Views: 2836
Size: 53.6 KB

jbclassix · 03-17-2011, 10:26 PM

Love the cruise pics

*project 67 sub* · 03-17-2011, 11:28 PM

thanks, i thought they were kind of cool to, but i like the show pics better though lol.

akgrown · 03-28-2011, 07:40 PM

Dropped burbs are probably a little more popular in Cali than over here in E. Washington, everyone who see's mine thinks it's a hearse. The paint schee probably doesn't help.

Nice ride though I like the direction it's going

*project 67 sub* · 03-28-2011, 11:41 PM

thanks guys for all the positive comments and props, it means alot

*project 67 sub* · 03-31-2011, 03:07 AM

a couple of pics i took of the burb layed out in the grass at a buddy of mines house. enjoy

Name: Photo03301843.jpg
Views: 459
Size: 47.1 KB

Name: Photo03301911.jpg
Views: 498
Size: 87.6 KB

**kev2809** · 03-31-2011, 10:10 PM

nice!!

*project 67 sub* · 04-01-2011, 03:56 AM

thanks, i try lol.

*project 67 sub* · 04-05-2011, 01:04 AM

not today, but yesterday. i took the 1.5" adapters/spacers off the rear, cut a small amount off of each wheel stud and put on my new 1" wheel adapter/spacers and aired it out to check for clearance on the fender, no rubbing

.

**kev2809** · 04-23-2011, 05:45 PM

hey hey! any updates?

*project 67 sub* · 04-24-2011, 02:58 AM

nah no updates other than i i drove it to another friends house in calimesa ca, and now i need to figure out why i have no tail lights/license plate light, have working turn signals but thats it. but other than that here is some motor pics from yesterday, and another pic of the piece parked in the street in front of the friends pad.
Name: Photo04221757.jpg
Views: 394
Size: 46.9 KB

Name: Photo04221757.jpg
Views: 394
Size: 46.9 KB

Name: Photo04221758.jpg
Views: 401
Size: 52.7 KB

Name: Photo04231321.jpg
Views: 401
Size: 88.0 KB

Newtz67 · 04-24-2011, 03:27 AM

That's a great lookin burb!

03-13-2011, 09:47 PM	#451
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: The '67 Burb Build Thread oh haha well then they didnt weld it properly or somthin like that

03-13-2011, 10:06 PM	#452
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread thats even funnier because the welds held just fine, it ripped in right about the middle. still havent went out to take it apart yet, but im sure the u joints are just fine, heck.... i even think the carrier bearing is just fine Last edited by project 67 sub; 03-13-2011 at 10:07 PM.

03-13-2011, 11:48 PM	#453
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: The '67 Burb Build Thread ok then it really is a mr e

03-14-2011, 01:12 AM	#454
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread went out and pulled out the drive shaft, all of the u joints and carrier bearing is fine, will take it in to have the tube replaced on the rear shaft in the morning. hopefully it wont cost me to much $$

03-14-2011, 02:51 AM	#455
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread

03-14-2011, 02:55 AM	#456
mmmBoost Registered User Join Date: Jan 2011 Location: Wisconsin Posts: 224	Re: The '67 Burb Build Thread Did it ever hit a cross member or anything with the bags deflated or aired all the way up? __________________ Always remember those that had your back Never forget those that turned it Demon 68- C20 (conv. 5 lug) 406sb, TH400, 12 Bolt, Red Slut 09- 1500 Crew Cab Z71, 2.5" Lift, Comp Cam, Deleted AFM/DoD, Diablo tuner

03-14-2011, 03:23 AM	#457
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread nope, didn't hit anything till it twisted in half, then it hit the bottom of the rear floor tunnel i had made for drive shaft clearance.

03-14-2011, 10:42 AM	#458
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,172	Re: The '67 Burb Build Thread thats the first time ive seen something like this. so when you get it replaced...how can you tell if its not gonna happen again? (as in, is there anything preventable to make sure it doesnt snap again?) __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

03-14-2011, 02:08 PM	#459
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread yah me to, i'm taking it to a local drive line guy to have him do the work, will ask him what he thinks, maybe have him put a bigger tube on it or something if that would even make a difference in strength

03-14-2011, 05:13 PM	#460
1sik7t2 dave Join Date: Jul 2007 Location: el cajon Posts: 558	Re: The '67 Burb Build Thread MY ONLY THOUGHT WOULD BE THE CRACK OR WEAK SPOT ALREADY METIONED OR UR PINION ANGLE IS WAY OFF....MAKIN EXTRA STRESS ON IT QUOTE=project 67 sub;4551888]yah me to, i'm taking it to a local drive line guy to have him do the work, will ask him what he thinks, maybe have him put a bigger tube on it or something if that would even make a difference in strength[/QUOTE] __________________ check out my build "DIRTY BURB"

03-15-2011, 12:20 AM	#461
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread well here is the fix, it cost me $100 , oh well, should be alot stronger now.

03-15-2011, 02:39 AM	#462
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: The '67 Burb Build Thread kucky at least you have a drive line to fix!

03-15-2011, 02:56 AM	#463
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread that isn't even the same rear shaft, that is a completely different one. its been changed from the splined yoke where the carrier bearing presses on all the way to the end. the center u-joint couldn't be reused because the new shaft had a wider joint peace, and then with the new center u-joint, the splined yoke piece had to be changed because the new u-joint didn't fit right in the old one

03-15-2011, 04:51 PM	#464
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread few more pics from the cruise me cruising next to leddzepp look in the mirror on this one lol. Last edited by project 67 sub; 03-15-2011 at 04:52 PM.

03-17-2011, 10:26 PM	#465
jbclassix Junk Yartist Join Date: Jul 2009 Location: Greeley, CO Posts: 2,203	Re: The '67 Burb Build Thread Love the cruise pics __________________ -Jeremy YOU ONLY FAIL IF YOU STOP TRYING 70 Crew Cab Build Link 70 GMC Suburban 4X4 build thread 95 Yukon Daily Driver Rebuilding an NP205



Register or Log In To remove these advertisements.

03-17-2011, 11:28 PM	#466
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread thanks, i thought they were kind of cool to, but i like the show pics better though lol.

03-28-2011, 07:40 PM	#467
akgrown Registered User Join Date: May 2010 Location: Cheney, WA Posts: 24	Re: The '67 Burb Build Thread Dropped burbs are probably a little more popular in Cali than over here in E. Washington, everyone who see's mine thinks it's a hearse. The paint schee probably doesn't help. Nice ride though I like the direction it's going __________________ 71 Chevy Suburban, 2wd, 350 V8, Air ride, 22's, headman headers, edelbrock carb, Ididit column, edelbrock intake manifold, Leather interior . _________ /____\|__\|__\____ \|__(O)______(O)_]

03-28-2011, 11:41 PM	#468
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread thanks guys for all the positive comments and props, it means alot

03-31-2011, 03:07 AM	#469
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread a couple of pics i took of the burb layed out in the grass at a buddy of mines house. enjoy

03-31-2011, 10:10 PM	#470
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,172	Re: The '67 Burb Build Thread nice!! __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

04-01-2011, 03:56 AM	#471
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread thanks, i try lol.

04-05-2011, 01:04 AM	#472
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread not today, but yesterday. i took the 1.5" adapters/spacers off the rear, cut a small amount off of each wheel stud and put on my new 1" wheel adapter/spacers and aired it out to check for clearance on the fender, no rubbing .

04-23-2011, 05:45 PM	#473
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,172	Re: The '67 Burb Build Thread hey hey! any updates? __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

04-24-2011, 02:58 AM	#474
project 67 sub Account Suspended Join Date: Mar 2007 Location: san bernardino ca. everywhere Posts: 3,938	Re: The '67 Burb Build Thread nah no updates other than i i drove it to another friends house in calimesa ca, and now i need to figure out why i have no tail lights/license plate light, have working turn signals but thats it. but other than that here is some motor pics from yesterday, and another pic of the piece parked in the street in front of the friends pad.

04-24-2011, 03:27 AM	#475
Newtz67 Registered User Join Date: Mar 2010 Location: A t w a t e r, Ca Posts: 1,201	Re: The '67 Burb Build Thread That's a great lookin burb! __________________ My '67 short wide Our '68 Burb My '04 Z71 The '54 Belair The '69 Cadillac

Register or Log In To remove these advertisements.