What did you do to your truck today?

[glendale]

painted a door and installed my door panel.

[lakeroadster]

Extended the '67 Camaro dash by 5" that is going into my 65 SWB SS. More pictures and tech. data in my build thread, listed below.

[truckdrivinsob]

Got the motor pretty much buttoned up. Ran fuel lines made battery cables. Hopefully fire her up tomorrow ! Then on to plumbing the compressor and valves. Then mount bags.

[Rich 5150 69]

Had to drop in a new HEI, the old one died last Friday, 3-miles from the house after a 250 mile trip, got towed the last three, the old HEI was `77 vintage all original, I would have rebuilt it but the centrifigal advance was rusted up tight, coild not get it apart. Kinda wondered why the last few months it wasn`t quite right....

[lakeroadster]

Added sheet metal to the strectched'67 Camaro dash that's going into my 65 C10.

[brandon283]

got the whole roof off my cab, and the roof panel peeled off the donor cab, next week should have the new roof on my cab

[sams60gmc]

Sprayed a little flat black on the truck, can't wait to get more done on the rear suspension this week.

[neiloneil]

had to add some character to my roof

[DPowers]

Finished bleeding my brakes, new rear shocks on and installed my driveshaft.

[Byronic]

I picked up a few supplies to help along with progress.
The aluminum gun and gas will be here Wed.

[Rusteeze64GB]

On Saturday, I went and bought and few gauges for my custom panel that I am going to make. I also bought a new headlight, some more paint. I installed a powersteering belt and put fluid in the power steering pump. I need to tighten the belt more it squeaks like crazy. Cleaned and installed my old tranny cooler, Cleaned up the wire harness under the dash. I added some tranny fluid, put some air in the front tire pulled the truck out of the driveway and rinsed it off. Just need to put new hardware, adjust,bleed the brakes, and wire up the voltage regulator. Trying to figure that one out. Should be on the street soon.

To do list

Install dynamat
carpet
Paint drivers side
Sand and Paint GMC grille
Fix parking Brake
Make Guage Panel and install gauges
Clean and Paint the Frame
Bolt the bed down
Put chrome trim on
Lower truck
Wheels and tires

the list gets longer everytime I work on it.

[jgh64pkup]

watcha weldin

[Byronic]

Originally Posted by jgh64pkup

watcha weldin

At last count there are 28 screw holes inside the cab. Not to mention the holes in the floor board.

[jgh64pkup]

with aluminum wire?

[Byronic]

Originally Posted by jgh64pkup

with aluminum wire?

No no. The aluminum is to weld my neighbors screen door shut.
I'm building pier carts for fishing down here in the gulf. I can make them for half of what they charge.

[Woogeroo]

Yesterday... I was checking some other thing under the hood and noticed fuel leaking from the fuel line on the back side of the inline fuel filter.

So, I took it off and cut a chunk out... and clamped it all back down.

I had been smelling raw fuel but I could not find the leak... hopefully that was the only one.

I also bought a new longer piece of fuel line to do a little rerouting.

-W

[blackmopar]

started building a battery box to relocate back behind the cab under the bed - dropped off the motor at a buddies shop this am to get some of the go fast parts taken care of (cam/lifter/intake/hei/etc) while I redo the wiring and battery runs this week

[ravens65]

Well, The first thing I did was to install a Flowmaster exhaust on my 16-year olds firebird ( chrismas present from me ) the nut didn't drop to far from the tree. hahaha of course he wanted to help ( till I broke out the welder!) I have 3 boys 10,16, 23 so they aren't suprised at any thing that I build , they have seen it all- guitars, cars, trucks, model A's , houses and art work , anyone else seems to be impressed , but its nothing but a thing to them ( even thought of building a jet engine @ one time ) till we researched how dangerious that they are (momma put a stop to that project!!)they have seen chevelles, a model a, 58 chevy truck, custom harleys, sand rails and several monster trucks,and 3 4-5-6ers there I go again off the subject ... Sorry ...... I have sometimers disease, sometimes I forget what we are talking about!!!! OK after the exhaust ,I ran my oak wood for the bed thru my planer . cant believe how ruff those kits are , should have made my own !! had to drive the truck out of the garage and up the hill so that we had room to work on the firebird 's exhaust . It looked so nice sitting up there that I broke out the camera . looks like it sits too high so more lowering is in store , if all the parts were on it I think it comes down some, we'll see . Eric

[1Bad62Pro/Street]

Originally Posted by ERIC BUFFARD

Well, The first thing I did was to install a Flowmaster exhaust on my 16-year olds firebird ( chrismas present from me ) the nut didn't drop to far from the tree. hahaha of course he wanted to help ( till I broke out the welder!) I have 3 boys 10,16, 23 so they aren't suprised at any thing that I build , they have seen it all- guitars, cars, trucks, model A's , houses and art work , anyone else seems to be impressed , but its nothing but a thing to them ( even thought of building a jet engine @ one time ) till we researched how dangerious that they are (momma put a stop to that project!!)they have seen chevelles, a model a, 58 chevy truck, custom harleys, sand rails and several monster trucks,and 3 4-5-6ers there I go again off the subject ... Sorry ...... I have sometimers disease, sometimes I forget what we are talking about!!!! OK after the exhaust ,I ran my oak wood for the bed thru my planer . cant believe how ruff those kits are , should have made my own !! had to drive the truck out of the garage and up the hill so that we had room to work on the firebird 's exhaust . It looked so nice sitting up there that I broke out the camera . looks like it sits too high so more lowering is in store , if all the parts were on it I think it comes down some, we'll see . Eric

Whatcha got plans for your bed bud? Seen where ya had to do some cuttin to make room for your hides.

[ravens65]

Originally Posted by 1Bad62Pro/Street

Whatcha got plans for your bed bud? Seen where ya had to do some cuttin to make room for your hides.

I have 72 inner fenders that I sectioned 4" out of , still looks factory but have 20'' of room for even fatter tires after I burn those off !! just took them off for body work and paint heres some pics for ya!!

[jgh64pkup]

so how does it sound

[ravens65]

like a six cylinder on steriods. noticable extra horse power, about 30 hp they claim, lets hope he can keep it between the lines . it already has a black door , a new tie rod, and a new pair of front tires from his last escapade!!!! do you remember when we were that young? Now I'm truely scared!!!! Eric

[65gmc930]

sweet truck!
What size are the tires?

[ravens65]

Originally Posted by 65gmc930

sweet truck!
What size are the tires?

390/40/17 M&H Racemaster drag radials rear , 245/45/17 Kumho all season front , I did a 3"-4" drop to the truck and after mounting the back tires I dropped the back 2" more. it still has a nice rake to it! back rims are 11" wide and the front are 8" wide, wanted 20" but 17" is the biggest slick that you can get. I had it all together once or twice and I think that it sits lower with all the extra weight on it

[jgh64pkup]

Originally Posted by ERIC BUFFARD

like a six cylinder on steriods. noticable extra horse power, about 30 hp they claim, lets hope he can keep it between the lines . it already has a black door , a new tie rod, and a new pair of front tires from his last escapade!!!! do you remember when we were that young? Now I'm truely scared!!!! Eric

oh its a v6
well iam that young so i remember it