![]() |
![]() |
#451 |
Registered User
Join Date: Aug 2012
Location: Salem Mo
Posts: 652
|
Re: 1957 Chevy truck re-rebuild
I had to take care of a small area that is seen but doesn't get much respect.
For those who have the Camaro clip, it's the upper control arm washers. ![]() I know if I paint them I will chip them when the nuts are tightened up against them. I must solve this problem.... ![]() Cutting the 4 blanks. ![]() Back to the press to get the cone shape. ![]() Then to the lathe to drill the 5/8" hole. ![]() Then some 1500 grit paper prior to polishing. ![]() Then to the drill press with a buffing wheel attached. ![]() Oh my, what an improvement. ![]() Look closely and you can see the ceiling fan blades spinning in the polished one. ![]() I ordered some stainless locking nuts so this area should be done for years to come.
__________________
My 57 Chevy truck build.http://67-72chevytrucks.com/vboard/s...d.php?t=541132 |
![]() |
![]() |
![]() |
#452 |
Registered User
Join Date: Feb 2013
Location: Lakeside Ariz
Posts: 445
|
Re: 1957 Chevy truck re-rebuild
Very nice idea. I will keep that in mind. Rich
my build http://67-72chevytrucks.com/vboard/s...64#post6690964 |
![]() |
![]() |
![]() |
#453 |
Registered User
![]() Join Date: May 2012
Location: Finley, TN.
Posts: 198
|
Re: 1957 Chevy truck re-rebuild
I would buy a set of those if you make more of them.
|
![]() |
![]() |
![]() |
#454 |
Registered User
Join Date: Feb 2011
Location: Clear Lake, MN
Posts: 329
|
Re: 1957 Chevy truck re-rebuild
that is what i call, attention to detail!
|
![]() |
![]() |
![]() |
#455 |
Registered User
Join Date: Aug 2012
Location: Salem Mo
Posts: 652
|
Re: 1957 Chevy truck re-rebuild
Thanks all, I've restored and worked on enough GM muscle cars and these washers have always been a thorn in my side. My side feels much better now that I'm past this issue.
![]() butchp, I'll keep you in mind if interest grows.
__________________
My 57 Chevy truck build.http://67-72chevytrucks.com/vboard/s...d.php?t=541132 |
![]() |
![]() |
![]() |
#456 |
Registered User
Join Date: Aug 2007
Location: Corona, California
Posts: 7,998
|
Re: 1957 Chevy truck re-rebuild
Those are some sharp washers.
Kim |
![]() |
![]() |
![]() |
#457 |
Registered User
Join Date: Apr 2011
Location: Virginia Beach, VA
Posts: 504
|
Re: 1957 Chevy truck re-rebuild
Jim, so how much for a set for my subframe?
![]() |
![]() |
![]() |
![]() |
#458 |
Registered User
Join Date: Aug 2012
Location: Salem Mo
Posts: 652
|
Re: 1957 Chevy truck re-rebuild
bowt1ed and butchp, I don't want to ignore your requests for these stainless washers. I'll cut a few blanks and get a couple sets made in the week or so. Price will be reasonable, they are labor intensive but if there is more interest I can devise faster ways of making them, thanks for your interest. Jim
Otherwise, nothing special tonight, just one more step in the list of many steps of restoring old vehicles. One of my disc brake dust shields was abused in the past so I found some used ones on e-bay. ![]() Nothing a little sand blasting can't handle. ![]() Hung up with a coat of epoxy primer. ![]() Painted and cleared, now sitting out in the sunlight drying. ![]() The silver is good on these shields works great, plus it is a test run to see if I like the silver as part of the two tone of the truck.
__________________
My 57 Chevy truck build.http://67-72chevytrucks.com/vboard/s...d.php?t=541132 |
![]() |
![]() |
![]() |
#459 |
56 - autocross
Join Date: Apr 2010
Location: Camarillo, Ca
Posts: 1,121
|
Re: 1957 Chevy truck re-rebuild
What sandblasting gun do you have? Is it in a cabinet?
I have a harbor freight blast cabinet that has been modified but was thinking about getting a TP Tools gun. I heard that they work much better. Your parts look like they came out well after blasting. Either you have a good gun or have patience with a slow gun. By the way, the silver is beautiful. I like the flake. |
![]() |
![]() |
![]() |
#460 | |
Registered User
Join Date: Aug 2012
Location: Salem Mo
Posts: 652
|
Re: 1957 Chevy truck re-rebuild
Quote:
Before anybody else brings it up, yes, be careful of breathing the dust while blasting, always wear protective gear. I do have a blast cabinet, but since the media is reused it can cause contamination which can result in fisheyes unless cleaned well before priming and painting. The sand blasting does leave a slightly rough texture, but with 2 coats of epoxy primer, it fills the texture pretty good for the paint.
__________________
My 57 Chevy truck build.http://67-72chevytrucks.com/vboard/s...d.php?t=541132 |
|
![]() |
![]() |
![]() |
#461 |
Registered User
Join Date: Jan 2010
Location: Tonasket, Washington
Posts: 316
|
Re: 1957 Chevy truck re-rebuild
Just getting caught up and Wow, Things are looking good.
__________________
-Aaron '15.5 Chevy Duramax LTZ/Z71, LML, CC/SB '77 Chevy K10, 4" lift, 33-12.50, 350/350 '55 Chevy Short Box (In Pieces)MII,4-link,Bagged,383 Stroker,700r4,3.73posi (SOLD) My 55.2 Chevy 3100 Build |
![]() |
![]() |
![]() |
#462 |
Registered User
Join Date: Aug 2012
Location: Salem Mo
Posts: 652
|
Re: 1957 Chevy truck re-rebuild
Slowly making progress..... I've pretty well finished the block sanding on the cab, front and rear fenders and doors.
It seems every painter has their procedures before paint. Right now I need to get the bottoms of the fenders painted. About a year ago I applied 2 coats of epoxy primer. Now I can scuff sand the epoxy. ![]() Next I apply one more slightly over reduced coat of epoxy primer. It will serve to cover any small areas that bare metal became exposed, fill sand scratches, help adhesion, seal and provide a consistent base for the paint to lay on. ![]() I forgot to take a picture in the shop, but after the painting I set them in the sunlight to dry. ![]() With the epoxy primer and paint I shouldn't have to do much more than an occasional pressure wash to clean up the undersides now.
__________________
My 57 Chevy truck build.http://67-72chevytrucks.com/vboard/s...d.php?t=541132 |
![]() |
![]() |
![]() |
#463 |
Registered User
Join Date: Dec 2011
Location: Mobile, Alabama
Posts: 996
|
Re: 1957 Chevy truck re-rebuild
The details you are providing will help us "soon to be" body guys. Thx. Dug
__________________
My Build - http://67-72chevytrucks.com/vboard/s...d.php?t=515876 |
![]() |
![]() |
![]() |
#464 | |
Registered User
Join Date: Aug 2012
Location: Salem Mo
Posts: 652
|
Re: 1957 Chevy truck re-rebuild
Quote:
Some time back I ordered a set of leaf springs, I think the brand was Possies, (spelling). When they got to me they were missing a couple of the round nylon sliders. As time passed by I knew I had to do something to get the new ones so I finally e-mailed them directly and for 20 bucks I got 10 of the sliders. Perhaps I could have gotten them for free, but having them was more important than the 20 bucks. ![]() The spring pack had a permanent clamp around the main leafs so I did paint these as a pack. ![]() I did however paint the other leafs individually them assembled the packs. ![]() It's always good to start reassembly. ![]() ![]() Getting a little dusty but it's at least a rolling chassis again. ![]()
__________________
My 57 Chevy truck build.http://67-72chevytrucks.com/vboard/s...d.php?t=541132 |
|
![]() |
![]() |
![]() |
#465 |
Registered User
Join Date: Feb 2013
Location: Lakeside Ariz
Posts: 445
|
Re: 1957 Chevy truck re-rebuild
The frame does look nice. Rich
|
![]() |
![]() |
![]() |
#466 |
Registered User
![]() Join Date: May 2012
Location: Finley, TN.
Posts: 198
|
Re: 1957 Chevy truck re-rebuild
The body shop guy has mentioned that he will spray truck liner under the fenders to protect from flying rocks putting reverse dents on the outside of the fenders.
|
![]() |
![]() |
![]() |
#467 |
Registered User
Join Date: Aug 2007
Location: Corona, California
Posts: 7,998
|
Re: 1957 Chevy truck re-rebuild
Looks real nice.
Kim |
![]() |
![]() |
![]() |
#468 |
Registered User
Join Date: Aug 2012
Location: Salem Mo
Posts: 652
|
Re: 1957 Chevy truck re-rebuild
Baldeagle SR, thanks, at this time of trying to get through so many odds and ends it's nice to go walk around a past accomplishment such as the frame to get your head back in the right attitude to keep moving forward.
Thanks Kim. butchp, you body guy has a good idea there. I have in the past seen the outward dents from rocks hitting the underside of a single panel fender as these trucks have. A couple of pics I have and would like to mention. First being the front coil springs and the compressor. While working to get the ride height set I had to use the spring compressor, and couple of times it was a fight to get it back out. If the arms were in the right place, it popped out fine, if the arms were slightly off, I had to do a little prying to remove it. The prying meant perhaps scratching the paint on the control arms on final assembly. The last time I removed the springs I took the picture. By using this picture I was able to reinstall the compressor arms in the same place on the springs. During reassembly, no fighting, no prying. ![]() One other photo is the upper control arm shims. Tape and mark each pack. Sure it will need to be realigned when done but by marking and putting them back in the same place gets you back in the pall park to get you to the alignment shop. ![]() The digital camera pics can be a time saver in the long run, it's always good to have a back up memory of odds and ends.
__________________
My 57 Chevy truck build.http://67-72chevytrucks.com/vboard/s...d.php?t=541132 |
![]() |
![]() |
![]() |
#469 |
Registered User
Join Date: Jan 2012
Location: Motown
Posts: 7,680
|
Re: 1957 Chevy truck re-rebuild
looking good stepside
![]() nice shiney washers. i did a thin coat of bedliner on the underside of truk, seems to be holding up fine.
__________________
cool, an ogre smiley ![]() how to put your truck year and build thread into your signature shop air compressor timer |
![]() |
![]() |
![]() |
#470 | |
Registered User
Join Date: Aug 2012
Location: Salem Mo
Posts: 652
|
Re: 1957 Chevy truck re-rebuild
Quote:
Oh how I want to get to the overall paint but I know I have to take care of the bottom sides of the front fenders and cab. One step at a time...... At this point I've sprayed one coat of epoxy primer over the epoxy I applied over a year ago, I did fully scuff the old primer first. ![]() One thing I wanted when I made the gills for the front fenders was to have them look somewhat original. I spent a little time cleaning up the welds before priming. Why the concern about the backside, the gills can be seen by looking into the front wheelwell. This way they look like they were press into the fender. ![]() ![]() Two coats of satin black. ![]() ![]() Couple more items off the checklist. ![]()
__________________
My 57 Chevy truck build.http://67-72chevytrucks.com/vboard/s...d.php?t=541132 |
|
![]() |
![]() |
![]() |
#471 |
Registered User
Join Date: Aug 2007
Location: Corona, California
Posts: 7,998
|
Re: 1957 Chevy truck re-rebuild
You're doing a real nice job.
Kim |
![]() |
![]() |
![]() |
#472 |
Registered User
Join Date: Feb 2014
Location: Honolulu, HI
Posts: 38
|
Re: 1957 Chevy truck re-rebuild
Nice
|
![]() |
![]() |
![]() |
#473 |
Registered User
Join Date: Aug 2011
Location: North Carolina
Posts: 275
|
Re: 1957 Chevy truck re-rebuild
Jim if you make/sell a set of those washer I would be interested in 2 sets. You wouldnt ave to polish them
__________________
1958 Chevy Apache Stepside 1955 BBW Fleetside |
![]() |
![]() |
![]() |
#474 |
Registered User
Join Date: Aug 2012
Location: Salem Mo
Posts: 652
|
Re: 1957 Chevy truck re-rebuild
Thanks Kim and Mr. Jones.
For months I've known the painting of all the odds and was going to be in the forefront. With as boring a job it is to paint the undersides of all the parts I have to remind myself that the better and more complete job I do, the longer it will be that I have to see any rust begin to start over the many years to come. apache200, yes, I am making the washers, please PM me and we'll get something arranged. ![]()
__________________
My 57 Chevy truck build.http://67-72chevytrucks.com/vboard/s...d.php?t=541132 |
![]() |
![]() |
![]() |
#475 |
Registered User
Join Date: Aug 2012
Location: Salem Mo
Posts: 652
|
Re: 1957 Chevy truck re-rebuild
It's been a while since I've done much of anything to the bottom of the cab.
Last time was when I sprayed 2 coats of epoxy primer. Often times when I'm going to spray high build primer over the epoxy I just do 1 coat of epoxy. In this situation I wasn't applying any high build, but I knew I was going to sand it at some point. By spraying the 2 coats I have enough thickness to sand without sanding through. Although I did get some incidental high build over spray on the bottom side, it got sanded along with the epoxy. ![]() Once again, to get good adhesion and a consistent base I sprayed 1 slightly over reduced coat of epoxy primer. ![]() Then onto two coats of satin black. Once again, the camera likes to turn the satin black into a digital mess, none the less, it's covered and safe from the elements. ![]() You know, sometimes we just have to step back in time and remember where we've been to appreciate how far we've come. Let's take a look shall we.... Firewall. ![]() Yup, I'm getting there..... ![]()
__________________
My 57 Chevy truck build.http://67-72chevytrucks.com/vboard/s...d.php?t=541132 |
![]() |
![]() |
![]() |
Bookmarks |
|
|