S!ck5 65 rebuild - Page 19 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Sick5 · 02-05-2014, 06:37 AM

Thanks I'll check it out..
Any going to the 99 speedway sunday

dr69burb · 02-05-2014, 03:47 PM

Looks good. Will the 64-66 bed wheel wells not fit? I just picked up a steel floor the other day. Do you have any more pics of how you put the bed floor in?

Sick5 · 02-05-2014, 04:17 PM

I made a mistake cutting the back corners to much.for me since I have raised my floor I cut about an inch on all cross beams under that bed floor. Then notch out the back corners.
On the install you have to remove one side Of the bed.
And you need 67-72 wheel tubs 60-66 too small

Sick5 · 05-14-2014, 11:08 PM

Getting **** moving. See you guys at brothers soon

Sick5 · 08-15-2014, 12:12 PM

Trying something new.!

Hardesty454 · 08-15-2014, 12:41 PM

Looks pretty good!

Quick question though, off subject but you don't know the diameter of the tube used on your porterbuilt bridge do you?

charlie8297 · 08-15-2014, 01:55 PM

I got a 65 GMC as well and am in the process of swapping out the 305 for a 350. Where did you get the wiring harness for the conversion? Thanks for the info!

Sick5 · 08-15-2014, 01:57 PM

I think it's an inch.but I can check

Sick5 · 08-15-2014, 02:04 PM

American auto wire... Charlie

Hardesty454 · 08-15-2014, 02:43 PM

Quote:

Originally Posted by Sick5

I think it's an inch.but I can check

If you could if appreciate it! Thanks!

charlie8297 · 08-15-2014, 03:34 PM

Thanks for the info.

Sick5 · 09-30-2014, 08:04 PM

Added the side mounding and working on new spot for the accuair

Sick5 · 10-20-2014, 03:53 PM

Quote:

Originally Posted by Hardesty454

If you could if appreciate it! Thanks!

Rob sorry i didnt get that info. Glad to finaly meet you @ Rene party.

Sick5 · 10-20-2014, 03:58 PM

Quote:

Originally Posted by dr69burb

Looks good. Will the 64-66 bed wheel wells not fit? I just picked up a steel floor the other day. Do you have any more pics of how you put the bed floor in?

matter of fact they do fit just need to shorten them 3 inches

Hardesty454 · 10-20-2014, 09:14 PM

Quote:

Originally Posted by Sick5

Rob sorry i didnt get that info. Glad to finaly meet you @ Rene party.

No problem on the size! It was good to see you again too. I'm going to try and see you guys more at the shows and what not. I was wondering about the size so I have a good variation of dies for my bender. I thought it was 1.5 .120 but apparently 1" is large enough.

Sick5 · 10-21-2014, 01:05 AM

Well your in luck since I hade pull the transmission out I can see what size is it. I'll do it tomorrow after work

Sick5 · 10-22-2014, 10:35 AM

Quote:

Originally Posted by Hardesty454

No problem on the size! It was good to see you again too. I'm going to try and see you guys more at the shows and what not. I was wondering about the size so I have a good variation of dies for my bender. I thought it was 1.5 .120 but apparently 1" is large enough.

well let me know if you still need that info

Hardesty454 · 10-22-2014, 10:52 AM

Quote:

Originally Posted by Sick5

well let me know if you still need that info

Yea, since you're going to be apart anyway if you could I'll take it for reference on what they use. Thank you!

Sick5 · 10-22-2014, 10:54 AM

So far you need tube size on the bridge right

Hardesty454 · 10-22-2014, 10:58 AM

Quote:

Originally Posted by Sick5

So far you need tube size on the bridge right

Yea. The bridge. Please.

Sick5 · 10-22-2014, 07:58 PM

1 1/2 hardest454

Hardesty454 · 10-22-2014, 08:42 PM

Thank you! Greatly appreciated!

Sick5 · 12-01-2014, 11:33 AM

working on my Accuair project. Most people have it installed under the bed. But i like the look of it on top of the bed.
I need to remove the the tank. reinstall new 3/8 air lines. i have 1/2 at the moment. I really wanted to buy the accuair au4 tank mount but dont have the cash. so i fig i would try to build my own. here some picture of the mount.

Sick5 · 12-01-2014, 11:36 AM

anyone know if its a good idea to weld on to the air tank? i got a few ideas for the airtank mount. using a chain to wrap around the airtank then from the chain to the accuair mount. just need to remove the tank and try it out

westcoast5 · 02-10-2015, 02:33 AM

waiting on porterbuilt stuff sucks lol

02-05-2014, 06:37 AM	#451
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild Thanks I'll check it out.. Any going to the 99 speedway sunday __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

02-05-2014, 03:47 PM	#452
dr69burb Registered User Join Date: Mar 2012 Location: San Diego CA Posts: 223	Re: S!ck5 65 rebuild Looks good. Will the 64-66 bed wheel wells not fit? I just picked up a steel floor the other day. Do you have any more pics of how you put the bed floor in? __________________ Baggin 64 lwb project http://67-72chevytrucks.com/vboard/s...d.php?t=537406

02-05-2014, 04:17 PM	#453
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild I made a mistake cutting the back corners to much.for me since I have raised my floor I cut about an inch on all cross beams under that bed floor. Then notch out the back corners. On the install you have to remove one side Of the bed. And you need 67-72 wheel tubs 60-66 too small __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

05-14-2014, 11:08 PM	#454
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild Getting **** moving. See you guys at brothers soon Attached Images __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

08-15-2014, 12:12 PM	#455
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild Trying something new.! Attached Images __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

08-15-2014, 12:41 PM	#456
Hardesty454 Registered User Join Date: Feb 2011 Location: Riverbank, Ca Posts: 1,006	Re: S!ck5 65 rebuild Looks pretty good! Quick question though, off subject but you don't know the diameter of the tube used on your porterbuilt bridge do you? __________________ Rob 1971 c10 - ground up in progress Tripp's Speed Shop Build - http://67-72chevytrucks.com/vboard/s...d.php?t=589750

08-15-2014, 01:55 PM	#457
charlie8297 Registered User Join Date: Sep 2012 Location: Placerville, CA Posts: 37	Re: S!ck5 65 rebuild I got a 65 GMC as well and am in the process of swapping out the 305 for a 350. Where did you get the wiring harness for the conversion? Thanks for the info!

08-15-2014, 01:57 PM	#458
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild I think it's an inch.but I can check __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

08-15-2014, 02:04 PM	#459
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild American auto wire... Charlie __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

08-15-2014, 03:34 PM	#461
charlie8297 Registered User Join Date: Sep 2012 Location: Placerville, CA Posts: 37	Re: S!ck5 65 rebuild Thanks for the info.

09-30-2014, 08:04 PM	#462
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild Added the side mounding and working on new spot for the accuair Attached Images __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

10-21-2014, 01:05 AM	#466
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild Well your in luck since I hade pull the transmission out I can see what size is it. I'll do it tomorrow after work __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

10-22-2014, 10:54 AM	#469
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild So far you need tube size on the bridge right __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

10-22-2014, 07:58 PM	#471
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild 1 1/2 hardest454 __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

10-22-2014, 08:42 PM	#472
Hardesty454 Registered User Join Date: Feb 2011 Location: Riverbank, Ca Posts: 1,006	Re: S!ck5 65 rebuild Thank you! Greatly appreciated! __________________ Rob 1971 c10 - ground up in progress Tripp's Speed Shop Build - http://67-72chevytrucks.com/vboard/s...d.php?t=589750



Register or Log In To remove these advertisements.

12-01-2014, 11:33 AM	#473
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild working on my Accuair project. Most people have it installed under the bed. But i like the look of it on top of the bed. I need to remove the the tank. reinstall new 3/8 air lines. i have 1/2 at the moment. I really wanted to buy the accuair au4 tank mount but dont have the cash. so i fig i would try to build my own. here some picture of the mount. Attached Images __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

12-01-2014, 11:36 AM	#474
Sick5 C10 CLUB Y QUE! Join Date: Mar 2010 Location: Here Posts: 2,770	Re: S!ck5 65 rebuild anyone know if its a good idea to weld on to the air tank? i got a few ideas for the airtank mount. using a chain to wrap around the airtank then from the chain to the accuair mount. just need to remove the tank and try it out __________________ C/10 CLUB http://67-72chevytrucks.com/vboard/f...play.php?f=148

02-10-2015, 02:33 AM	#475
westcoast5 Registered User Join Date: Jul 2012 Location: salinas,ca Posts: 296	Re: S!ck5 65 rebuild waiting on porterbuilt stuff sucks lol __________________ *Bryan* 1966 SWB BBW "SICKT6" Accuair\|Porterbuilt\|Bodied\|Shaved\|Z'd\|350 with minor goodies\|5 lug\|front disc\|3.73 rear\|CPP power steering/brakes\|few more goodies\| thanks to C10Clubapparel

Register or Log In To remove these advertisements.