What did you do to your truck today! - Page 199 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

VDOG · 11-23-2012, 07:38 PM

Quote:

Originally Posted by Jimbabwe

Technically this was yesterday, but you get the idea.

Like how this sits, is it static or an airbag drop?

Jimbabwe · 11-23-2012, 07:52 PM

Quote:

Originally Posted by VDOG

Like how this sits, is it static or an airbag drop?

Thank you. It's bagged, with Porterbuilt front and rear. Finishing it up now. Driveshaft, etc...

Jimbabwe · 11-23-2012, 07:56 PM

Quote:

Originally Posted by VDOG

Like how this sits, is it static or an airbag drop?

Sorry, I forgot. Here's my link with a little info if you were thinking of going that route with your stepper.

http://67-72chevytrucks.com/vboard/s...d.php?t=545435

midniteblues · 11-23-2012, 11:48 PM

got my cm prepped for running the exhaust through it. I gotta cut the tubes a lil' shorter before welding them in. I just might cut one in half and use the two halves.

VDOG · 11-25-2012, 01:00 AM

Quote:

Originally Posted by Jimbabwe

Sorry, I forgot. Here's my link with a little info if you were thinking of going that route with your stepper.

http://67-72chevytrucks.com/vboard/s...d.php?t=545435

Thanks for the link. I was going to pull a trailing arm setup from the wrecking yard, just did not know if I needed the complete rearend, or just the arms and u-bolts.

UNEASYRIDER · 11-23-2012, 06:13 PM

Quote:

Originally Posted by ChillWinstonC20

Uneasyrider, looks like you've got the most important tools out and in use...

Yes Sir. A little liquid to get the job done!

ChillWinstonC20 · 11-22-2012, 11:34 PM

Went shopping yesterday. New wires, plugs and guides tomorrow.

Shyguy · 11-24-2012, 12:55 AM

My son drove my '67 swb steeper out to my house in the country today, first time on the road since we just finished building it.

Just one slight problem, it died and would not start about 3 blocks from my son's house.

We went back to my son's and got some supplies and tools. He checked for spark-ok, checked for fuel at carb, none. He finally isolated it to the tank as being why there was no fuel getting to the carb. He removed the pickup tube/sending unit and found that the sock had broken apart and plugged the pickup line.

Got the line all cleared out and away we went, it got home ok.

CMH77 · 11-24-2012, 01:04 AM

Today I yanked the old, dead I6 250 out of the engine bay. Tomorrow I hope I will be posting that the new, healthy I6 250 is put together from breather to oilpan and back in the truck.

**allchevy58** · 11-24-2012, 01:17 AM

Got dash back together, new ac vent hoses, new vacuum hoses on heater/ac control, new fan switch, new speaker, installed underdash lights and glovebox light purchased from forum member, new glovebox cardboard, installed blue leds in cluster, radio and heater/ac control unit. Installed new fan shroud also purchased from forum member.

*bk2life* · 11-24-2012, 04:28 AM

got more parts in the mail!! woohooo

kaycee · 11-24-2012, 01:19 PM

Heres the seats 60/40 split 99 Tahoe seats ,good junkyard find ($100)

sumtercleaner · 11-25-2012, 04:05 PM

Quote:

Originally Posted by kaycee

Heres the seats 60/40 split 99 Tahoe seats ,good junkyard find ($100)

Many mods to make tahoe seats work? Any more leg room under sterring wheel?
Posted via Mobile Device

UNEASYRIDER · 11-25-2012, 09:43 PM

Used left over seat material for my sub box

Trsmotrhed · 11-25-2012, 10:09 PM

Uneasy, I don't see the beer. Lol. I'm having a beer for ya now. Looks good. Keep up the good work.
Posted via Mobile Device

69GWC · 11-24-2012, 01:34 PM

Wow $100 bucks :O man crazy good price and looks great.
Posted via Mobile Device

Mayo · 11-25-2012, 12:11 AM

Finally wired up the reverse lights to my LED lightbar
Posted via Mobile Device
Posted via Mobile Device

romeer1 · 11-25-2012, 12:42 AM

Painted my frame and re-installed brake booster.

*bk2life* · 11-26-2012, 07:17 AM

more parts!!! woohooooo

Mayo · 11-26-2012, 06:17 PM

I sanded the paint off my door locks and then polished them up
Posted via Mobile Device
Posted via Mobile Device
Posted via Mobile Device

ItsRandy · 11-26-2012, 09:30 PM

Got an O2 bung welded into the header reducer. Going to put the truck on a chassis dyno and tune the motor, needed the O2 bung for that.

rico7769 · 11-27-2012, 12:09 AM

finally ordered carpet and kick panel sets after 4 years of fixing her up. Installed the new door panels, armrests, j channel, etc last week. Ready to order the seat cover next payday and she will be almost done...well, on the inside

jonny..2008 · 11-27-2012, 12:28 AM

finally got the trailing arm bushings replaced.
still the panhard bar to go.

tomis blair · 11-27-2012, 10:48 AM

Replaced my cracked and dryrotted 31x10.50x15s with some new 275/60/15 primewells. Shes much more happy now!

dhaymaker · 11-27-2012, 11:00 AM

Quote:

Originally Posted by tomis blair

Replaced my cracked and dryrotted 31x10.50x15s with some new 275/60/15 primewells. Shes much more happy now!

Any "before" and "after" pictures for us?

11-23-2012, 11:48 PM	#4
midniteblues Registered User Join Date: Jul 2011 Location: strausstown pa Posts: 3,394	Re: What did you do to your truck today! got my cm prepped for running the exhaust through it. I gotta cut the tubes a lil' shorter before welding them in. I just might cut one in half and use the two halves. Attached Images __________________ 81 camaro 355 4/spd 342 posi my first love. 67 swb step 454/4spd ott 373 posi 4/7 drop. 2000 s10 zr2 little blue truck that never gets stuck. '74 heald super bronc vt8. tecumseh powered moon rover.

11-22-2012, 11:34 PM	#7
ChillWinstonC20 Registered User Join Date: Aug 2012 Location: Cbus, OH Posts: 48	Re: What did you do to your truck today! Went shopping yesterday. New wires, plugs and guides tomorrow.

11-24-2012, 12:55 AM	#8
Shyguy Junior Member Join Date: Dec 2006 Location: Southeast Missouri Posts: 2,436	Re: What did you do to your truck today! My son drove my '67 swb steeper out to my house in the country today, first time on the road since we just finished building it. Just one slight problem, it died and would not start about 3 blocks from my son's house. We went back to my son's and got some supplies and tools. He checked for spark-ok, checked for fuel at carb, none. He finally isolated it to the tank as being why there was no fuel getting to the carb. He removed the pickup tube/sending unit and found that the sock had broken apart and plugged the pickup line. Got the line all cleared out and away we went, it got home ok. __________________ '67 Chevy C-20 short stepper - build complete, 454/SM-465. '75 C-30 Single Cab DRW-350 small block/NP-435. '77 GMC-6500 Dump Truck, 427 Tall Deck. '92 GMC K-3500 Duallie, 454/4L80E.

11-24-2012, 01:04 AM	#9
CMH77 Registered User Join Date: Sep 2012 Location: Springfield, IL Posts: 71	Re: What did you do to your truck today! Today I yanked the old, dead I6 250 out of the engine bay. Tomorrow I hope I will be posting that the new, healthy I6 250 is put together from breather to oilpan and back in the truck. Last edited by CMH77; 11-24-2012 at 01:21 AM.

11-24-2012, 01:17 AM	#10
allchevy58 Senior Member Join Date: Aug 2011 Location: Reno, Nv. Posts: 1,430	Re: What did you do to your truck today! Got dash back together, new ac vent hoses, new vacuum hoses on heater/ac control, new fan switch, new speaker, installed underdash lights and glovebox light purchased from forum member, new glovebox cardboard, installed blue leds in cluster, radio and heater/ac control unit. Installed new fan shroud also purchased from forum member. __________________ 1927 Willy's Knight 24,000 original miles, 1958 Impala 283/Powerglide, 1964 C-30 383/4 speed, 1971 Monte Carlo 350/350, 1972 GMC K2500 350/350, 1976 Chev. K10 350/350, 2006 GMC Sierra 2500HD LBZ Duramax/Allison, 2006 Chev. Silverado K3500 LBZ Duramax/Allison

11-24-2012, 04:28 AM	#11
bk2life Account Suspended Join Date: Oct 2012 Location: phx, az Posts: 868	Re: What did you do to your truck today! got more parts in the mail!! woohooo

11-24-2012, 01:19 PM	#12
kaycee Registered User Join Date: Jan 2000 Location: Wyoming USA Posts: 2,445	Re: What did you do to your truck today! Heres the seats 60/40 split 99 Tahoe seats ,good junkyard find ($100) Attached Images __________________ 2001 Silverado K-1500 2005 FXDWG stage3 69 CHEVY Short/Step 327/4L60 373 posi 63 IMPALA 327

11-25-2012, 09:43 PM	#14
UNEASYRIDER Registered User Join Date: Apr 2009 Location: PHOENIX,ARIZONA Posts: 91	Re: What did you do to your truck today! Used left over seat material for my sub box __________________ DON'T BUILD IT IF YOUR NOT GONA DRIVE IT!!

11-25-2012, 10:09 PM	#15
Trsmotrhed Registered User Join Date: Mar 2012 Location: Pueblo West, Colorado Posts: 430	Re: What did you do to your truck today! Uneasy, I don't see the beer. Lol. I'm having a beer for ya now. Looks good. Keep up the good work. Posted via Mobile Device __________________ Sold the 63 and have a 68 now. 63 SWB C10 LT1/4L60E, PS, PB, Disk Brakes, CPP 4" drop coil rear, 2.5" drop spindle w/ 1" drop coil. slotted rotors, front and rear sway bars. 18"x8" Cragar SS w/ 245/45R18 http://67-72chevytrucks.com/vboard/s...d.php?t=544174

11-24-2012, 01:34 PM	#16
69GWC Registered User Join Date: Jun 2012 Posts: 1,089	Re: What did you do to your truck today! Wow $100 bucks :O man crazy good price and looks great. Posted via Mobile Device

11-25-2012, 12:11 AM	#17
Mayo Cool Truck Join Date: Dec 2008 Location: Bowie,MD Posts: 1,869	Re: What did you do to your truck today! Finally wired up the reverse lights to my LED lightbar Posted via Mobile Device Posted via Mobile Device Attached Images __________________ 1968 Chevrolet C20 Longhorn "Cool Truck" 1937 Chevrolet Pickup - Project Looking for a patina'd 68 50th Anniversary longbed

11-25-2012, 12:42 AM	#18
romeer1 Registered User Join Date: May 2011 Location: Georgia Posts: 72	Re: What did you do to your truck today! Painted my frame and re-installed brake booster. Attached Images __________________ Superman

11-26-2012, 07:17 AM	#19
bk2life Account Suspended Join Date: Oct 2012 Location: phx, az Posts: 868	Re: What did you do to your truck today! more parts!!! woohooooo

11-26-2012, 06:17 PM	#20
Mayo Cool Truck Join Date: Dec 2008 Location: Bowie,MD Posts: 1,869	Re: What did you do to your truck today! I sanded the paint off my door locks and then polished them up Posted via Mobile Device Posted via Mobile Device Posted via Mobile Device Attached Images __________________ 1968 Chevrolet C20 Longhorn "Cool Truck" 1937 Chevrolet Pickup - Project Looking for a patina'd 68 50th Anniversary longbed

11-26-2012, 09:30 PM	#21
ItsRandy Registered User Join Date: Nov 2010 Location: Grand Terrace, Ca. Posts: 1,607	Re: What did you do to your truck today! Got an O2 bung welded into the header reducer. Going to put the truck on a chassis dyno and tune the motor, needed the O2 bung for that.



Register or Log In To remove these advertisements.

11-27-2012, 12:09 AM	#22
rico7769 Hybrid67 Join Date: Jan 2009 Location: Martinez, GA Posts: 195	Re: What did you do to your truck today! finally ordered carpet and kick panel sets after 4 years of fixing her up. Installed the new door panels, armrests, j channel, etc last week. Ready to order the seat cover next payday and she will be almost done...well, on the inside __________________ Keep em' Running! All show.....no go

11-27-2012, 12:28 AM	#23
jonny..2008 Registered User Join Date: Sep 2012 Location: oregon coast Posts: 248	Re: What did you do to your truck today! finally got the trailing arm bushings replaced. still the panhard bar to go. __________________ i love every machine. even the ones i hate. Current project (1959) fifty niner gmc fleetside: http://67-72chevytrucks.com/vboard/s...70#post6514670 MY daily driver truck thread : http://67-72chevytrucks.com/vboard/s...d.php?t=544460

11-27-2012, 10:48 AM	#24
tomis blair Registered User Join Date: Apr 2012 Location: grants pass oregon Posts: 40	Re: What did you do to your truck today! Replaced my cracked and dryrotted 31x10.50x15s with some new 275/60/15 primewells. Shes much more happy now!

Register or Log In To remove these advertisements.