CA Parting 71 Custom Camper 20

[jocko]

How much would you like for the raised oil fill tube/screws, etc and cap shipped to 76028?

Also - am interested in the brake distro block/prop valve AND its electrical connection (you can just cut the wire as long as you can, but no need to get fancy). Was the brake light on all the time prior to stripdown? If not, how much shipped to same addr? (you can just snip the lines and leave them attached - i.e. please leave fittings intact if you don't mind). Or did this go with the front disk brakes you already sold?

Thanks!

[cheyenne shortstep]

bluek5, here is what you get. If you need the big bracket that sandwiches the pedal I will throw one in.

B.W., I will gather up what I've got and get back to you.

[cheyenne shortstep]

jocko, I'll do $45 shipped for the oil fill w/ screws & cap. This brake set up is going with the brakes but I probably have what your looking for, 71/72 dist. block, fittings and wire end?

B.W., still working on A.C. stuff, so far I have most of what you need.

[jocko]

Ok, thanks for checking shortstep - I believe I'll just take the oil fill setup. Will pm you for details. Thanks!

[bluek5]

Originally Posted by cheyenne shortstep

bluek5, here is what you get. If you need the big bracket that sandwiches the pedal I will throw one in.

B.W., I will gather up what I've got and get back to you.

Send me your payment information again. It's been a little while.
Thanks, Paul

[johnscab]

Did this have power steering? If so how much for the pump, brackets, pulleys and box. Any pix also appreciated.

[B. W.]

Thanks, I'm in no hurry, truck's in a million pieces (am i restoring it or parting it? Sometimes I forget!)

[tj_1970_k20]

What type of rear axle does it have?

[cheyenne shortstep]

tj 1970 k20, it is a 4:10 Dana 60 for leaf spring suspension [non posi].

[Dimebagdavesc30]

Is the heater switch still available.....thanks

[SIXTY9]

Looking for the steering column bracket and clamp that is on firewall under master cylinder with the bolts,and shipping to 29418

[rcm1958]

What does the tailgate look like?? My current gate is really crusty, bent, etc.. The truck deserves something better!

Let me know-

[tj_1970_k20]

Can you measure the center to center distance between the rear springs for me?

[cheyenne shortstep]

Johnscab, P.S. setup sold locally.

tj 1970 k20, axle measures 42&1/2" center perch to center perch. It will not fit 4x4 if that's what you're after.

Dimebagdavesc30, Do you need a fan switch or complete A.C./heater control?

Sixty9, $20 shipped for column clamp, bracket & screws.

rcm1958, As stated ALL sheetmetal is rusted, the gate is being made into a bench.

[johnscab]

Originally Posted by cheyenne shortstep

Johnscab, P.S. setup sold locally.

tj 1970 k20, axle measures 42&1/2" center perch to center perch. It will not fit 4x4 if that's what you're after.

Dimebagdavesc30, Do you need a fan switch or complete A.C./heater control?

Sixty9, $20 shipped for column clamp, bracket & screws.

rcm1958, As stated ALL sheetmetal is rusted, the gate is being made into a bench.

Thank you, sir!

[SIXTY9]

Will you please pm your information on how you would like payment. Thanks

[Dimebagdavesc30]

I need a complete switch. Thanks

[cheyenne shortstep]

Dimebagdavesc30, I'm a little confused. Do you need a fan blower switch or complete A.C. control unit?

[Dimebagdavesc30]

I need heat control assembly with heat only, my whole dash switch is missing levers, just have face plate. I don't need the ac one but the whole switch assembly.

[cheyenne shortstep]

Dimebagdavesc30, OK so you need this complete heater control unit. It is in good solid condition with a little weathering on the face. $90 shipped

[Dimebagdavesc30]

and it's sold wipe me your stuff and I'll zip the money off.... thanks

[72lady]

Hi I'm interested in the Ac/heat vacuum actuators and brackets if they are good. Cowl one and the one on the passenger kick panel. Shipped to 29360. Thanks

[cheyenne shortstep]

68350, I found the other Custom Camper/20 emblem if you are still interested, not really pitted just need cleaning, all studs intact. $30 shipped

B.W. I am getting another truck that I believe the A.C. boxes are intact. otherwise I have everything. I'll know in a day or 2.

72lady, are these what you are after? If so $25

[72lady]

Originally Posted by cheyenne shortstep

68350, I found the other Custom Camper/20 emblem if you are still interested, not really pitted just need cleaning, all studs intact. $30 shipped

B.W. I am getting another truck that I believe the A.C. boxes are intact. otherwise I have everything. I'll know in a day or 2.

72lady, are these what you are after? If so $25

Posted via Mobile Device

[72lady]

Originally Posted by 72lady

Posted via Mobile Device

Yes those are the ones. Do you know if they will hold a vacuum? If so I'll take them.
Posted via Mobile Device