67 Camaro Build

[7dee2]

Bummer, that looked like it could have been a good'n! I’ll ask around and keep my eyes open for yah Chris, thanks.



Here's a little more jig/cart progress and then a planets are aligning kind of moment! Our new beauty tank has been on fumes and the second it was out our 10lb wire spool ran out also.

[7dee2]

Some poly bushings, tub o’ grease and oil filter adaptor bolts showed up from Summit. Slid the subframe back under the car again with the new bushings prior to repairing the bad LR body mount hole. Toying with the idea of making our jig able to accept the subframe for front clip fitment later (?).

[Dieselwrencher]

Man, using the hoist is cheating, but I really like it. Maybe I could use a drive on to lift bodies off just like you did?

[bryant6]

Big project... what’s been done looks pretty good. I'm so jealous

[7dee2]

Originally Posted by rgunlock

Sucks when that happens! Can you tack a bar across the top to hold your spacing while you reweld the gussets?

Yeah, tacking a brace in place woulda, coulda, shoulda been a better idea. Or maybe leaving the cars weight on em?

Originally Posted by Dieselwrencher

That's just how it goes isn't it? Oh well, you'll get it fixed up.

It’s always something!

Originally Posted by bryant6

Big project... what’s been done looks pretty good. I'm so jealous

Thanks Bryan!



So, after cutting the four tops off, cleaning off all the not so old weld and trueing everything up again. With the weight of the car tacked them in place with lots of tacks then pulled and final welded them onto the uprights again. Once satisfied with the support to body fit again went ahead and welded up the rest of it. Yippy skippy, shell went right on without any drama this time!

[CG]

Im not a big fan of Camaros but when you posted Grumps Camaro that brought back some fun memories. I think a 67/68 Camaro set up with the same stance and tire wheel combo would be really cool to bomb around in.

[7dee2]

Originally Posted by Dieselwrencher

Man, using the hoist is cheating, but I really like it. Maybe I could use a drive on to lift bodies off just like you did?

Ha, you know it, we use this lift as a body/frame elevator, paint booth, project storage, etc. it continues to be a great tool!

Originally Posted by CG

Im not a big fan of Camaros but when you posted Grumps Camaro that brought back some fun memories. I think a 67/68 Camaro set up with the same stance and tire wheel combo would be really cool to bomb around in.

I think so too, that's the plan, a rake with some Cragar SS’s. Pizza cutters up front and some sticky's in tha back!



Building a jig/body cart that won't fall apart and is next up.

[gringoloco]

Nice work on that. Way better than buying new

[Clyde65]

Well done! Always wanted to have a welding talent!

[7dee2]

Originally Posted by gringoloco

Nice work on that. Way better than buying new

Thanks Chris I agree, much better than buying new.

Originally Posted by Clyde65

Well done! Always wanted to have a welding talent!

Thanks Clyde, it's coming along pretty good.




Flipped over for another pass, added some nice ugly weld on the end like the factory welds. Ha, thinking that'll do!

[Dieselwrencher]

Nice work. Much better than the rust hole before.

[7dee2]

Thanks Ryan!

Hole’s been punched and subframe test fitted into the car, giving this particular repair a done stamp.

[rgunlock]

Nice repair Brett. You weren't kidding about leaving the ugly welds on the end

[gringoloco]

Looks factory, nice!

[7dee2]

Originally Posted by rgunlock

Nice repair Brett. You weren't kidding about leaving the ugly welds on the end

Thanks Rick, as a friend likes to say “bigger the glob better the job”!

Originally Posted by gringoloco

Looks factory, nice!

Thanks Chris, since we're only fixing one mount Mr. Picky Pants (me?) wanted to hide the repair.



Back to the jig, mentioned this earlier making both the front and middle supports height adjustable in case we want to add the subframe with its mounts at some point and still level out the body shell. All thread pieces are slotted and cut as long as the tubes so they can be recessed flush but not fall in.

[Dieselwrencher]

That's a very nice body dolly! Can you make one for my Camaro and my 40 Ford so I don't have to?

[7dee2]

Yepper, I’m thinking it’s gonna be nice! Hey Ryan, that is a good idea, but no..


Here’s how we’re anchoring the rear, using the old 2-piece frame bushings with the shoulders cut off for a closer flush mount. Then to the risers using the original shackles, it’s pretty dang snug and a bear to install but will hold the car very solid. Getting ready for a gusset party next!

[7dee2]

1, 2 & 6, gusset parties over, good times… I’m thinking this is gonna work with the subframe!

[7dee2]

Argh! Too much heat, pulled the uprights inward towards the gussets dangnabit! The alignment holes up front don’t line up any more, it just barely fit through the subframe and the center support section was off by a knat’s a** of popping into its alignment holes. Cutting the tops off and am resetting them.

It's another Mr. Bean moment...

[rgunlock]

Sucks when that happens! Can you tack a bar across the top to hold your spacing while you reweld the gussets?

[Dieselwrencher]

That's just how it goes isn't it? Oh well, you'll get it fixed up.

[Dieselwrencher]

Nice! Is the body ready for paint yet?

[7dee2]

No but, Tada we do have a cart/jiggy dealio!

Credit for this design goes to a YouTuber, MrFireman164 and his 68 Camaro build, liked his design the best of what I could find out there. It’s probably overkill but it’ll hold the car from moving really, really well and can be transported for paint, etc. when the time comes.

[gringoloco]

Very, very nice

[mongocanfly]

that turned out good....