1970 c20 l9h 6l90e

[boynton]

This is a complete rework that makes this swap much easier.

http://www.currentperformance.com/sh...-modification/

here is what I bought that helped me with my modified harness

http://www.currentperformance.com/sh...erelay-module/

hope this helps with the wiring decision.

As far as your exhaust manifolds, I used trailblazer SS manifolds and only had to trim a very minor piece from the right side of the frame. You should be able to see it on page 3/4 of my One Owner Short Step build thread.

[boynton]

Do you have any pictures of the LS3 manifolds in place? I really thought these would fit too.

[Hart_Rod]

Originally Posted by boynton

do you have any pictures of the ls3 manifolds in place? I really thought these would fit too.

+1

[1970C20L9H]

When I got home from work last night the hooker manifolds were waiting for me...



Here are a few photos of them installed. They fit perfect with plenty of room to breath. I think they look pretty damn nice too.

[1970C20L9H]

Originally Posted by boynton

Do you have any pictures of the LS3 manifolds in place? I really thought these would fit too.

I did not take any photos. I guess I can do that. I was thinking about maybe relocating the engine 2.5" to the rear by bolting the motor mount perch to what I understand to be the 6 cylinder mounting location and see if that makes any more room for the exhaust manifolds. Either that or I may try out the hooker headers cast iron manifolds. Part number 8501HKR or ceramic coated 8501-4HKR

[bigmone]

The Hooker swap manifolds will work and fit great

[1970C20L9H]

I took a photo and then I removed the heat shield and tested fitment without it and it was closer to fitting but still no luck.

Here are the photos....

This is with the heat shield obviously. I have a loose bolt in the first flange to hold it in place, the rear of the manifold is sitting about 1.5 inches above where it needs to be...


Now here is a photo with no heat shield. It's close, but no cigar. All of the bolts are in, I started to tighten the bolts but the collector flange is binding on the upper frame rail from below.

[Hart_Rod]

those don't look different than the Camaro headers I have (2010+), I wonder if they are Corvette ? Here's some pictures of mine.

[1970C20L9H]

Originally Posted by Hart_Rod

those don't look different than the Camaro headers I have (2010+), I wonder if they are Corvette ? Here's some pictures of mine.

I assume you meant those look different than the camaro headers you have.

You are right, they are different, and from my research I think they are LS2 exhaust manifolds. Those Camaro manifolds you have look like they would work. Are you using the ECE motor mounts?

[Hart_Rod]

Originally Posted by 1970C20L9H

I assume you meant those look different than the camaro headers you have.

You are right, they are different, and from my research I think they are LS2 exhaust manifolds. Those Camaro manifolds you have look like they would work. Are you using the ECE motor mounts?

That's correct. Those picture are of my Son's 68 with a Porterbuilt setup, so the clearance should be similar to yours. I think the 2010+ Camaro manifolds will work.

[1970C20L9H]

I am still trying to decide between 2010+ camaro exhaust manifolds or just buying the hookers. People are just asking too damn much for a pair of used exhaust manifolds ($150-$200) and I figure the hookers probably flow better.

[Hart_Rod]

Originally Posted by 1970C20L9H

I am still trying to decide between 2010+ camaro exhaust manifolds or just buying the hookers. People are just asking too damn much for a pair of used exhaust manifolds ($150-$200) and I figure the hookers probably flow better.

You can usually get them for about a $100 shipped on the Camaro5.com website.

[bigmone]

Go with the Hookers they come in different coatings as well

[1970C20L9H]

So, I spent $141.25 on eBay for the wrong exhaust manifolds (That includes shipping).

I immediately listed them myself when I realized they would not work for me and sold them for $100 + $20 shipping. Paypal took their cut of $3.78, eBay took their cut of $12 the actual ground shipping charge was $44.45 so I recouped $59.77 from my initial $141.25 investment. So I only lost $81.48 on the deal.

[1970C20L9H]

I am ready to move onto fuel now. Is anyone running the stock tank behind the seat with an inline pump?

[Xeen]

Originally Posted by 1970C20L9H

I am ready to move onto fuel now. Is anyone running the stock tank behind the seat with an inline pump?

I have seen several guys do this mod, Holley makes durable reliable fuel pumps, they are a bit pricey but worth it though.
If you go this route you are gonna want to mount the pump inside the frame rail, not in the cab because it would be annoying.
I have also seen several guys do the "in tank" pump mod but unfortunately I can't remember specific builds so I can't point you to them directly.
In the LSX swap section is where you will find them usually in the "budget" builds.

[Xeen]

Very nice, those are the exact exhaust manifolds I would have recommended if I would have seen the clearance issue earlier.

[bigmone]

Yes sir told you man they are great for swaps and they flow great! You can get the O-ring gaskets for the collectors from your local parts store I have the part numbers if u can't find them

[1970C20L9H]

Originally Posted by bigmone

Yes sir told you man they are great for swaps and they flow great! You can get the O-ring gaskets for the collectors from your local parts store I have the part numbers if u can't find them

If its not too much trouble I would love the part numbers.

[1970C20L9H]

I got the part numbers, They were listed on the instructions that came with the manifolds.

Exhaust manifold to cylinder head gasket part # 12617944
Exhaust manifold to cylinder head bolts part # 11518860 or 11547135
Exhaust manifold outlet seal part # 92202326
Exhaust manifold outlet studs 10mmx1.5 part # 11589264
Exhaust manifold stud nuts 10mmx1.5 part # 15032594

All together about $155 from gmpartsdirect but I already have the manifold head bolts so about $120

[bigmone]

Originally Posted by 1970C20L9H

I got the part numbers, They were listed on the instructions that came with the manifolds.

Exhaust manifold to cylinder head gasket part # 12617944
Exhaust manifold to cylinder head bolts part # 11518860 or 11547135
Exhaust manifold outlet seal part # 92202326
Exhaust manifold outlet studs 10mmx1.5 part # 11589264
Exhaust manifold stud nuts 10mmx1.5 part # 15032594

All together about $155 from gmpartsdirect but I already have the manifold head bolts so about $120

All you need is the Oring gaskets and the studs and nuts to hook the pipes up should be under 30$ easily

[1970C20L9H]

Anyone have experience with Holly billet inline fuel pump? Part number 12-700? I am thinking about using this, gravity fed, by stock in cab tank.

[bigmone]

The O ring gaskets actually cross over to Pontiac G8 and a few other cars like the Acadia but not a 2010 Camaro.. The studs are in the help section of most part stores

[kitsbeach]

This is looking pretty cool.! Love the shop truck look. It'll surprise a few people once the LS is up and running.

Thanks for the pics too. I have an LS swap planned in the future.

[1970C20L9H]

Originally Posted by kitsbeach

This is looking pretty cool.! Love the shop truck look. It'll surprise a few people once the LS is up and running.

Thanks for the pics too. I have an LS swap planned in the future.

Thanks, If yours is original paint and I suspect it is I hope you don't paint yours either. It's beautiful just like it is.