Bubba's recycling project - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bubba327 · 12-02-2010, 12:20 AM

Quote:

Originally Posted by 63lemon

What year nova steering coulmns would bolt right up to my 63 c10, i want tilt but i wanna keep my four on the floor

I am not sure if any Nova tilts Will "Bolt right up" But with a little creativity I made the 77 Nova column fit and come out very nice. But I sure put a LOT of time and trial and error fabricating in it.
Probably a Ididit or Flaming river Column might bolt in a little easier but I like a good challenge.

Vernski-- You win with the snow level!! we got 10 inches of it today and it was plenty wet!! Your new shop is looking good. I see one truck made it inside.

Dave --Where did you find those awesome square gray stack-able supports holding up the bed ??? Very useful items. I have a few just like them also.
Your garage is full!!! you need a SHOP and a shop cat to get the mice!

1964C10 · 10-06-2009, 11:00 AM

As far as ebrake is concerned, I am moving mine to the inner side panel where the air vent is. I am covering that up and mounting it there using a pedal assembly from a 80's van if I remember correctly. I also bought an adjustable ebrake cable from Lokar. I know I am losing the airvent but I have really long legs and I am constantly scraping them on the handle.

bubba327 · 10-20-2009, 11:13 PM

Name: IMG_2256.jpg
Views: 11885
Size: 41.5 KB

Finally got all the brackets built. E-brake works great. Wiring harness comes later in the project. Planning a cover for the wiring under the column.
Had to add 1 wire under the dash for a hazard flasher( orange wire to flasher , brown wire up to column switch ) and now all directional lighting works perfect! Everything else wired up color to existing color. The new orange wire comes from the hot side of the brake light switch , using the same circuit so the hazard light quit flashing when the brake lights are on. (as per 1977 Chevy wiring diagram)

Name: IMG_2257.jpg
Views: 17969
Size: 43.2 KB

Name: IMG_2257.jpg
Views: 17969
Size: 43.2 KB

Finished tilt steering column . I removed the lock mechanism and ignition switch and ground off the un-used lock casting, Machined a piece of aluminum for a plug that press fit into the hole left by the lock, epoxied in place and added a roll pin that I drilled in from inside the collar.Press fit piece was sanded smooth to match and painted. Looks great ,no trace that a key ever existed.
Steering wheel was found installed in a Buick 4-door in the local the Pick-A -Part. Maybe a mid 80's Chevy Camaro sport wheel? Dunno what it came from, but it was only $8.00...

Name: IMG_2259.jpg
Views: 13141
Size: 45.6 KB

Name: IMG_2259.jpg
Views: 13141
Size: 45.6 KB

The 64 E-brake highly modified to fit a 77 Tilt column.

Gee-- it is good to be attaching and posting again.. Bubba

daverod · 10-20-2009, 11:18 PM

Getting some stuff done.

Looks nice.

bubba327 · 10-20-2009, 11:30 PM

Quote:

Originally Posted by daverod

Getting some stuff done.

Looks nice.

Now the old three speed transmission has been removed and the automatic Is ready to go in as soon as I borrow a transmission jack.

daverod · 10-20-2009, 11:49 PM

Quote:

Originally Posted by bubba327

Now the old three speed transmission has been removed and the automatic Is ready to go in as soon as I borrow a transmission jack.

Sweet. Still waiting to see how much mines going to cost. Guess it had a few gears messed up.

**Captainfab** · 10-21-2009, 01:05 AM

That has turned out real nice Bubba.

Imperial Kustom · 10-21-2009, 08:00 PM

Dang Bruce! That all looks fantastic! Nice, clean, factory appearing work. Just what I like to see.

Truck Dr. · 10-21-2009, 08:26 PM

Bubba, I can't tell from the pics which 6 is this, 292 ??

Dave

bubba327 · 10-21-2009, 11:44 PM

Quote:

Originally Posted by Truck Dr.

Bubba, I can't tell from the pics which 6 is this, 292 ??

Dave

It is a 230-- the block number says it is a 250, The 230 & 250 pistons both are 3.875 bore,and the crank casting number says it is a 194 crank . The 194 and 230 are both 3.250 stroke and will interchange. So a 194 crank in a 250 block is really a 230 cu. Hey, I did not put it there, but it runs fine!!

Truck Dr. · 10-21-2009, 11:53 PM

Quote:

Originally Posted by bubba327

It is a 230-- the block number says it is a 250, The 230 & 250 pistons both are 3.875 bore,and the crank casting number says it is a 194 crank . The 194 and 230 are both 3.250 stroke and will interchange. So a 194 crank in a 250 block is really a 230 cu. Hey, I did not put it there, but it runs fine!!

The reason I was asking is that looks like the bracket from a 292, I got one from a guy parting out a 75 truck (I think it was) with a 250, ended up it was a 292.... it would not fit the 250 without a lot of mods, so I'm still looking for brackets for PS to fit a 250.

Dave

Vernski · 10-22-2009, 04:31 PM

[QUOTE=Truck Dr.;3580244]The reason I was asking is that looks like the bracket from a 292, I got one from a guy parting out a 75 truck (I think it was) with a 250, ended up it was a 292.... it would not fit the 250 without a lot of mods, so I'm still looking for brackets for PS to fit a 250.

Hey Truck Dr check out this link this where i got my mount from he may still have some or could find you one, give him a PM ---Vernski

http://www.67-72chevytrucks.com/vboa...d.php?t=355548

Vernski · 10-22-2009, 07:47 PM

Bubba I have a link for you if you haven't seen it yet I think you will like it. sorry about posting three times in a row.---Vernski

http://prostores1.carrierzone.com/se...com/StoreFront

bubba327 · 10-21-2009, 11:53 PM

Vernski-- I love your motor pictures. It that really an Offenhauser valve cover AND a Clifford intake??

Dave-Yeah-- I know you were wondering what to get me for Christmas this year...1 Offenhauser intake and three Strombergs please!!!

Vernski · 10-22-2009, 04:15 PM

[QUOTE=bubba327;3580243]Vernski-- I love your motor pictures. It that really an Offenhauser valve cover AND a Clifford intake??

Hi Bubba yeah that's an offy also the side covers match but have no name. I got the cover from Jegs and the side covers from Langdon's stovebolt, The intake is a Clifford, it is hot water heated, the carb is a Edelbrock # 1404 500 cfm w/manual chock. I rebuilt the stock one barrel twice and I could get it to idle the mid range was balky get the mid range right it wouldn't idle. It has a marine cam from Mercruiser but runs smooth from idle on up. The air cleaner came from ebay I can't remember the name right now but I have a slip somewhere. Thanx---Vernski

PS to Cap thanx for the compliment, will bring it by but it may be in the spring right now it has some bare metal I need to get covered up.--Vernski

bubba327 · 10-22-2009, 12:12 AM

Truck dr.--You might have the bracket from an integrated head 250. My bracket came from 250 pre-intregrated head. I do not know if the 292 takes a different mount or not. I looked for a LONG time to find this one.
I found 1 on E-bay last week and told a friend but he missed out on the bidding . It went for $99.00. Watch E-bay! I have seen several since I started but they bring $75-$125 with lots of activity. Good luck Bubba

**Captainfab** · 10-22-2009, 01:22 AM

The 6 cyl power steering setups show up every once in a while here in the '67-'72 classifieds. They might on the '73-'87 classifieds too, but I don't check there much.

That engine is looking sweet Vern! Hope to see it in person one of these days.

Truck Dr. · 10-23-2009, 12:11 AM

Vernski, thanks man for the link I'll shoot him a pm for sure.

Captainfab, thanks for the info, I'll start keeping an eye on the listings.

Bubba yea the truck that I got that brackets from was a 74 not a 5, and it was a 292 as I ended up buying it and put it in my 65 burb.

Seeing all these engine pics sure makes me want to get back working on my 67.

What a great bunch folks here and a whole slew of awesome trucks, thanks again for all the help.

Dave

bubba327 · 10-24-2009, 01:02 AM

YEAH!!! The turbo 350 transmission is in place. Then it rained and I had to stop. Maybe tomorrow I can get the rear tranny brace tightened and the starter installed.

daverod · 10-24-2009, 10:05 AM

Quote:

Originally Posted by bubba327

YEAH!!! The turbo 350 transmission is in place. Then it rained and I had to stop. Maybe tomorrow I can get the rear tranny brace tightened and the starter installed.

They do have these things called garages. You better hurry winter coming.

I know you have a garage but it ether full of yard sale stuff or thats where the old lady parks her car.

bubba327 · 10-24-2009, 10:36 AM

Name: IMG_1727.jpg
Views: 1818
Size: 52.3 KB

It will fit in there -but the chevelle is like a cat... It doesn't get wet!!

1964C10 · 10-24-2009, 11:46 AM

Quote:

Originally Posted by bubba327

Attachment 507451
It will fit in there -but the chevelle is like a cat... It doesn't get wet!!

Hahahaha...classic! Nice Chevelle btw!

daverod · 10-24-2009, 03:33 PM

Ok, I was feeling sorry for ya, but no more.

ol Curt · 10-24-2009, 08:34 PM

Bubba,

Is that a factory color on the truck in the garage?

bubba327 · 10-24-2009, 11:12 PM

Name: IMG_1831.jpg
Views: 1672
Size: 45.6 KB

Paint code says light blue- A 1964 standard color It has been repainted once but is very close to original. It appears washed out in the florescent lights in the garage. This is a summer picture when the front end was out. Do a google search for www.autocolorlibrary.com It has all the old paint colors from the old days

10-06-2009, 11:00 AM	#2
1964C10 Registered User Join Date: Mar 2008 Location: San Marcos, CA Posts: 578	Re: At Last- Power steering in a I-6 As far as ebrake is concerned, I am moving mine to the inner side panel where the air vent is. I am covering that up and mounting it there using a pedal assembly from a 80's van if I remember correctly. I also bought an adjustable ebrake cable from Lokar. I know I am losing the airvent but I have really long legs and I am constantly scraping them on the handle. __________________ 1964 Fleetside LWB 1995 Yellow Mustang convertible 1996 Camaro Z28 My build thread Looking for help on completing the Disc Brake Upgrade Reference Thread If you didn't build it, you don't really own it

10-20-2009, 11:13 PM	#3
bubba327 HOW long until spring?? Join Date: Mar 2009 Location: Star Idaho Posts: 1,413	Re: At Last- Power steering in a I-6 Finally got all the brackets built. E-brake works great. Wiring harness comes later in the project. Planning a cover for the wiring under the column. Had to add 1 wire under the dash for a hazard flasher( orange wire to flasher , brown wire up to column switch ) and now all directional lighting works perfect! Everything else wired up color to existing color. The new orange wire comes from the hot side of the brake light switch , using the same circuit so the hazard light quit flashing when the brake lights are on. (as per 1977 Chevy wiring diagram) Finished tilt steering column . I removed the lock mechanism and ignition switch and ground off the un-used lock casting, Machined a piece of aluminum for a plug that press fit into the hole left by the lock, epoxied in place and added a roll pin that I drilled in from inside the collar.Press fit piece was sanded smooth to match and painted. Looks great ,no trace that a key ever existed. Steering wheel was found installed in a Buick 4-door in the local the Pick-A -Part. Maybe a mid 80's Chevy Camaro sport wheel? Dunno what it came from, but it was only $8.00... The 64 E-brake highly modified to fit a 77 Tilt column. Gee-- it is good to be attaching and posting again.. Bubba __________________ 69 chevelle convertible 71-C-10 short-wide and low 64 C-10 custom shortbox "Bubba"s Recycling project"

10-20-2009, 11:18 PM	#4
daverod SSN 706 Join Date: Mar 2009 Location: Pocatello Idaho Posts: 3,821	Re: At Last- Power steering in a I-6 Getting some stuff done. Looks nice. __________________ Daverods 64 C10 Daily driver 292 3 speed "Driver" Daverods 66 Build C10 Bags 350/350(On Hold) Daverods 52 Build 3100 S10 chassis,Bags, 350/700r4 "Click it"

10-21-2009, 01:05 AM	#7
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,246	Re: At Last- Power steering in a I-6 That has turned out real nice Bubba. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

10-21-2009, 08:00 PM	#8
Imperial Kustom 100% gearhead Join Date: Apr 2007 Location: Boise, Idaho Posts: 313	Re: At Last- Power steering in a I-6 Dang Bruce! That all looks fantastic! Nice, clean, factory appearing work. Just what I like to see. __________________ Imperial Kustom LLC Meridian Idaho. I never stopped playing with cars, they just got bigger.

10-21-2009, 08:26 PM	#9
Truck Dr. Registered User Join Date: Oct 2009 Location: Rio Rancho NM Posts: 74	Re: At Last- Power steering in a I-6 Bubba, I can't tell from the pics which 6 is this, 292 ?? Dave __________________ Dave & Marilyn in Rio Rancho NM....1967 Chevrolet C-10 long step side.....250 3 spd. ..... 1968 Chevrolet C-10 long step side.....325 hp 350 4spd.....3" Exhaust....etc. 1965 Chevrolet Suburban K-10....292 4spd....cam....etc. Bow Tie Baby

10-22-2009, 04:31 PM	#12
Vernski Registered User Join Date: May 2009 Location: Rathdrum, Idaho Posts: 1,135	Re: At Last- Power steering in a I-6 [QUOTE=Truck Dr.;3580244]The reason I was asking is that looks like the bracket from a 292, I got one from a guy parting out a 75 truck (I think it was) with a 250, ended up it was a 292.... it would not fit the 250 without a lot of mods, so I'm still looking for brackets for PS to fit a 250. Hey Truck Dr check out this link this where i got my mount from he may still have some or could find you one, give him a PM ---Vernski http://www.67-72chevytrucks.com/vboa...d.php?t=355548

10-22-2009, 07:47 PM	#13
Vernski Registered User Join Date: May 2009 Location: Rathdrum, Idaho Posts: 1,135	Re: At Last- Power steering in a I-6 Bubba I have a link for you if you haven't seen it yet I think you will like it. sorry about posting three times in a row.---Vernski http://prostores1.carrierzone.com/se...com/StoreFront

10-21-2009, 11:53 PM	#14
bubba327 HOW long until spring?? Join Date: Mar 2009 Location: Star Idaho Posts: 1,413	Re: At Last- Power steering in a I-6 Vernski-- I love your motor pictures. It that really an Offenhauser valve cover AND a Clifford intake?? Dave-Yeah-- I know you were wondering what to get me for Christmas this year...1 Offenhauser intake and three Strombergs please!!! __________________ 69 chevelle convertible 71-C-10 short-wide and low 64 C-10 custom shortbox "Bubba"s Recycling project"

10-22-2009, 04:15 PM	#15
Vernski Registered User Join Date: May 2009 Location: Rathdrum, Idaho Posts: 1,135	Re: At Last- Power steering in a I-6 [QUOTE=bubba327;3580243]Vernski-- I love your motor pictures. It that really an Offenhauser valve cover AND a Clifford intake?? Hi Bubba yeah that's an offy also the side covers match but have no name. I got the cover from Jegs and the side covers from Langdon's stovebolt, The intake is a Clifford, it is hot water heated, the carb is a Edelbrock # 1404 500 cfm w/manual chock. I rebuilt the stock one barrel twice and I could get it to idle the mid range was balky get the mid range right it wouldn't idle. It has a marine cam from Mercruiser but runs smooth from idle on up. The air cleaner came from ebay I can't remember the name right now but I have a slip somewhere. Thanx---Vernski PS to Cap thanx for the compliment, will bring it by but it may be in the spring right now it has some bare metal I need to get covered up.--Vernski

10-22-2009, 12:12 AM	#16
bubba327 HOW long until spring?? Join Date: Mar 2009 Location: Star Idaho Posts: 1,413	Re: At Last- Power steering in a I-6 Truck dr.--You might have the bracket from an integrated head 250. My bracket came from 250 pre-intregrated head. I do not know if the 292 takes a different mount or not. I looked for a LONG time to find this one. I found 1 on E-bay last week and told a friend but he missed out on the bidding . It went for $99.00. Watch E-bay! I have seen several since I started but they bring $75-$125 with lots of activity. Good luck Bubba __________________ 69 chevelle convertible 71-C-10 short-wide and low 64 C-10 custom shortbox "Bubba"s Recycling project"

10-22-2009, 01:22 AM	#17
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,246	Re: At Last- Power steering in a I-6 The 6 cyl power steering setups show up every once in a while here in the '67-'72 classifieds. They might on the '73-'87 classifieds too, but I don't check there much. That engine is looking sweet Vern! Hope to see it in person one of these days. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE Last edited by Captainfab; 10-22-2009 at 01:23 AM.

10-23-2009, 12:11 AM	#18
Truck Dr. Registered User Join Date: Oct 2009 Location: Rio Rancho NM Posts: 74	Re: At Last- Power steering in a I-6 Vernski, thanks man for the link I'll shoot him a pm for sure. Captainfab, thanks for the info, I'll start keeping an eye on the listings. Bubba yea the truck that I got that brackets from was a 74 not a 5, and it was a 292 as I ended up buying it and put it in my 65 burb. Seeing all these engine pics sure makes me want to get back working on my 67. What a great bunch folks here and a whole slew of awesome trucks, thanks again for all the help. Dave __________________ Dave & Marilyn in Rio Rancho NM....1967 Chevrolet C-10 long step side.....250 3 spd. ..... 1968 Chevrolet C-10 long step side.....325 hp 350 4spd.....3" Exhaust....etc. 1965 Chevrolet Suburban K-10....292 4spd....cam....etc. Bow Tie Baby

10-24-2009, 01:02 AM	#19
bubba327 HOW long until spring?? Join Date: Mar 2009 Location: Star Idaho Posts: 1,413	Re: At Last- Power steering in a I-6 YEAH!!! The turbo 350 transmission is in place. Then it rained and I had to stop. Maybe tomorrow I can get the rear tranny brace tightened and the starter installed. __________________ 69 chevelle convertible 71-C-10 short-wide and low 64 C-10 custom shortbox "Bubba"s Recycling project"

10-24-2009, 10:36 AM	#21
bubba327 HOW long until spring?? Join Date: Mar 2009 Location: Star Idaho Posts: 1,413	Re: At Last- Power steering in a I-6 It will fit in there -but the chevelle is like a cat... It doesn't get wet!! __________________ 69 chevelle convertible 71-C-10 short-wide and low 64 C-10 custom shortbox "Bubba"s Recycling project"



Register or Log In To remove these advertisements.

10-24-2009, 03:33 PM	#23
daverod SSN 706 Join Date: Mar 2009 Location: Pocatello Idaho Posts: 3,821	Re: At Last- Power steering in a I-6 Ok, I was feeling sorry for ya, but no more. __________________ Daverods 64 C10 Daily driver 292 3 speed "Driver" Daverods 66 Build C10 Bags 350/350(On Hold) Daverods 52 Build 3100 S10 chassis,Bags, 350/700r4 "Click it"

10-24-2009, 08:34 PM	#24
ol Curt Junior Member Join Date: Dec 2006 Location: Newburgh, IN Posts: 1,247	Re: At Last- Power steering in a I-6 Bubba, Is that a factory color on the truck in the garage? __________________ 1966 Chevy C10 Longbed I'm Bob....ol Curt was my Grandpa The truck was his and he sure as heck wouldn't understand why I took a perfectly good truck and tore it down!

10-24-2009, 11:12 PM	#25
bubba327 HOW long until spring?? Join Date: Mar 2009 Location: Star Idaho Posts: 1,413	Re: At Last- Power steering in a I-6 Paint code says light blue- A 1964 standard color It has been repainted once but is very close to original. It appears washed out in the florescent lights in the garage. This is a summer picture when the front end was out. Do a google search for www.autocolorlibrary.com It has all the old paint colors from the old days __________________ 69 chevelle convertible 71-C-10 short-wide and low 64 C-10 custom shortbox "Bubba"s Recycling project"

Register or Log In To remove these advertisements.