|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
06-23-2016, 04:39 PM
|
#26 |
|
Registered User
Join Date: Apr 2010
Location: Boise, ID
Posts: 1,280
|
Re: Can I add a pusher fan to stock set-up?
I do. I am going to have to find the right spacer, it is cheaper to try that first.
|
|
|
|
06-23-2016, 05:36 PM
|
#27 | ||
|
20' Daredevil (Ret)
 
Join Date: May 2003
Location: Jefferson State
Posts: 13,655
|
Re: Can I add a pusher fan to stock set-up?
Quote:
Quote:
 You should not need any spacer -- the clutch unit should have a flange that bolts directly to the WP, no additional spacer needed or desired. Yours may be different if non-stock parts have been swapped in.
__________________
- Mike - 1972 K20 LWB 350/350/205 RIP El Jay |
||
|
|
|
|
06-24-2016, 09:41 AM
|
#28 |
|
Registered User
Join Date: Apr 2010
Location: Boise, ID
Posts: 1,280
|
Re: Can I add a pusher fan to stock set-up?
Ok, I think I tried that and the bolts were too long, then bought shorter bolts that were too short =) Will look at it again.
|
|
|
|
|
06-24-2016, 10:24 AM
|
#29 |
|
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,943
|
Re: Can I add a pusher fan to stock set-up?
This is how you want a stock clutch fan to look in the stock shroud.
  
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
|
|
|
|
06-24-2016, 02:28 PM
|
#30 | |
|
20' Daredevil (Ret)
Join Date: May 2003
Location: Jefferson State
Posts: 13,655
|
Re: Can I add a pusher fan to stock set-up?
Quote:
__________________
- Mike - 1972 K20 LWB 350/350/205 RIP El Jay |
|
|
|
|
|
06-24-2016, 03:50 PM
|
#31 |
|
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,943
|
Re: Can I add a pusher fan to stock set-up?
That setup work perfect for about 20 years in my truck. I never once had a over heating issue with it.
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
|
|
|
|
06-26-2016, 10:32 AM
|
#32 |
|
Registered User
Join Date: Apr 2010
Location: Boise, ID
Posts: 1,280
|
Re: Can I add a pusher fan to stock set-up?
Good Advice, am working on it this morning. Thanks.
|
|
|
|
|
07-02-2016, 11:47 PM
|
#33 |
|
20' Daredevil (Ret)
Join Date: May 2003
Location: Jefferson State
Posts: 13,655
|
Re: Can I add a pusher fan to stock set-up?
Any follow-up on this?
__________________
- Mike - 1972 K20 LWB 350/350/205 RIP El Jay |
|
|
|
|
07-03-2016, 01:46 AM
|
#34 |
|
Registered User
Join Date: Jan 2014
Location: Wasilla Alaska
Posts: 537
|
Re: Can I add a pusher fan to stock set-up?
Another idea. You said you put a" new long nose water pump on. Is that why the fan is so close to the Rad.?
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
