The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board > Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 06-26-2020, 10:23 AM   #1
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

Quote:
Originally Posted by joedoh View Post
man those pointy frame ends have claimed almost every pair of my work shorts, they all have the same tear in the right leg.

nice work, nice your daughter made it work safe too. you need a "__ days since workplace accident" sign now.
, that's a great idea...
csmeutah is offline   Reply With Quote
Old 07-12-2020, 12:01 PM   #2
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

I've spent several weeks cleaning up the front suspension components and replacing the bushings. No small feat on an independent suspension system.

Name:  suspension1.jpg
Views: 1235
Size:  54.8 KB

Now on to the rear end
csmeutah is offline   Reply With Quote
Old 07-12-2020, 12:02 PM   #3
8man
Senior Member
 
Join Date: Sep 2017
Location: Bryan, Texas
Posts: 2,357
Re: 1952 Pickup Street Rod project

Looks nice!
__________________
8man-aka Robert
1948 on a S10 Frame, small block with a carb
1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD
Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL]
[/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204
8man is offline   Reply With Quote
Old 08-25-2020, 10:18 AM   #4
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

Been working on the rear end, lots of u-joints and brake parts to clean up not to mention the oil seals.

Oh and I've been building a pizza oven at the same time...Name:  pizza oven.jpg
Views: 1169
Size:  73.9 KB
csmeutah is offline   Reply With Quote
Old 08-25-2020, 08:00 PM   #5
joedoh
Senior Member
 
joedoh's Avatar
 
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
Re: 1952 Pickup Street Rod project

if I tell you how clean this work is, will you invite me over for some pizza?

(its clean work even if you dont invite me for pizza)
__________________
the mass of men live lives of quiet desperation


if there is a problem, I can have it.

new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393
joedoh is offline   Reply With Quote
Old 08-25-2020, 09:16 PM   #6
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Wink Re: 1952 Pickup Street Rod project

Quote:
Originally Posted by joedoh View Post
if I tell you how clean this work is, will you invite me over for some pizza?

(its clean work even if you dont invite me for pizza)
The invite is the easy part, the drive from Kansas to Utah not so much.��
csmeutah is offline   Reply With Quote
Old 09-25-2020, 04:33 PM   #7
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

Finally got the rear end reassembled and finishing off the installation:

Name:  TruckRearEnd.jpg
Views: 1009
Size:  66.2 KB

I will be switching over to the body work as I wait for a donor for the driveline.

Last edited by csmeutah; 10-01-2020 at 06:32 PM.
csmeutah is offline   Reply With Quote
Old 12-09-2020, 03:08 PM   #8
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

Hi all, I know you have been worried sick waiting for my next post, well I can say that I have good news. I just brought home a 2000 convertible corvette that will be the donor for my driveline and other misc. parts. I'm also hoping to modify the convertible top frame for use on the truck, stay tuned:

Name:  20201209_110006.jpg
Views: 916
Size:  46.6 KB
csmeutah is offline   Reply With Quote
Old 12-09-2020, 03:15 PM   #9
8man
Senior Member
 
Join Date: Sep 2017
Location: Bryan, Texas
Posts: 2,357
Re: 1952 Pickup Street Rod project

Interesting! I'm in for the build.
__________________
8man-aka Robert
1948 on a S10 Frame, small block with a carb
1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD
Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL]
[/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204
8man is offline   Reply With Quote
Old 12-10-2020, 12:32 AM   #10
oldman3
Senior Member
 
oldman3's Avatar
 
Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,559
Re: 1952 Pickup Street Rod project

Sounds like we may be in for another roadster pickup...Jim
oldman3 is offline   Reply With Quote
Old 07-06-2021, 03:40 PM   #11
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

So my cousin-in-law spent a long morning helping me drop the LS1, now I get to strip it down and get the Vette carcass out of the way so I can start placing the engine in the truck. I am poring over similar blogs for LS engine orientation but any suggestions would be appreciated.
Attached Images
 
csmeutah is offline   Reply With Quote
Old 04-10-2022, 07:30 PM   #12
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

We placed the engine with some aftermarket weld in engine mounts. I have the engine angled 4 degrees down in the back, it is aligned 3/4" above the clocked rack and pinion in the front. Any concerns before I weld this in place? I will now plan to place the transmission and then the cab to determine fitment of the sheet metal and the exhaust.

Any feed back would be appreciated.
Attached Images
    
csmeutah is offline   Reply With Quote
Old 04-10-2022, 07:57 PM   #13
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,197
Re: 1952 Pickup Street Rod project

Maybe throw some manifolds, or headers or whatever you plan, on there just to ensure clearance.
On 1 build I did I reshaped the steel tube on the rack for a little more clearance.
dsraven is offline   Reply With Quote
Old 04-11-2022, 11:40 AM   #14
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

Quote:
Originally Posted by dsraven View Post
Maybe throw some manifolds, or headers or whatever you plan, on there just to ensure clearance.
On 1 build I did I reshaped the steel tube on the rack for a little more clearance.
Thanks DSRAVEN, is 3/4" clearance enough? How about front to back clearance, that's about as forward as I can go...
csmeutah is offline   Reply With Quote
Old 04-11-2022, 01:10 PM   #15
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,197
Re: 1952 Pickup Street Rod project

3/4 is probably enough on the rack. since you are running urethane mounts I would see what you have for clearance from the hot exhaust, maybe run a heat shield there and on the starter if it is close. there are some factory starter shields out there if you peruse the wrecking yards. one of those under floor exhaust shields from a car may also be reshaped if you need something for the mounts. maybe reshape the steel line on the rack and see where you're at there for clearance. on one of my builds I welded some flat bar to the frame and then bolted the engine mounts (frame side) onto those. then they could be unbolted easily for quick engine removal and also new holes could be drilled should there be a height adjustment needed or an engine swap to a different engine block style, etc. just a thought.
for engine height, I usually try to keep the oil pan above the frame in the same area. if going over one of those crazy high speed bumps or trying to miss that garbage in the middle of your lane the frame will hit rather than your oil pan. do you have room to go up more or you'd rather not? what about the driveline bellhousing, will it interfere with the floor if the engine raises?
dsraven is offline   Reply With Quote
Old 04-11-2022, 02:01 PM   #16
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

Quote:
Originally Posted by dsraven View Post
3/4 is probably enough on the rack. since you are running urethane mounts I would see what you have for clearance from the hot exhaust, maybe run a heat shield there and on the starter if it is close. there are some factory starter shields out there if you peruse the wrecking yards. one of those under floor exhaust shields from a car may also be reshaped if you need something for the mounts. maybe reshape the steel line on the rack and see where you're at there for clearance. on one of my builds I welded some flat bar to the frame and then bolted the engine mounts (frame side) onto those. then they could be unbolted easily for quick engine removal and also new holes could be drilled should there be a height adjustment needed or an engine swap to a different engine block style, etc. just a thought.
for engine height, I usually try to keep the oil pan above the frame in the same area. if going over one of those crazy high speed bumps or trying to miss that garbage in the middle of your lane the frame will hit rather than your oil pan. do you have room to go up more or you'd rather not? what about the driveline bellhousing, will it interfere with the floor if the engine raises?
All good points, thanks. I added the starter so I can account for clearance as I add the tranny/cab/exhaust. The crossmember on the front suspension hangs down 3/4" below the oilpan so that should catch any road issues first. I'm trying to keep the engine as low as possible for added cab/tranny/clearance and weight center of gravity but at this point I think I will add the components as you mention before the final motor mount weld. Thanks again.
Attached Images
 
csmeutah is offline   Reply With Quote
Old 08-22-2022, 02:17 PM   #17
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

Name:  Tranny.jpg
Views: 535
Size:  69.6 KB

I found a Tranny that looks like it will work, the mount fits nicely on a piece of C-channel. I am working on the exhaust next before I finalized the Transmission mount.

Meanwhile I'm also finishing up the electric Vespa project I've been working on with my daughter:

Name:  Scooter.jpg
Views: 536
Size:  56.4 KB

Name:  Estee.jpg
Views: 538
Size:  42.1 KB

As always, any suggestions are welcome as I finalize the driveline.
csmeutah is offline   Reply With Quote
Old 08-25-2022, 11:40 PM   #18
e015475
Registered User
 
e015475's Avatar
 
Join Date: Nov 2013
Location: Show Low, Arizona
Posts: 775
Re: 1952 Pickup Street Rod project

I'd think with a Corvette bat-wing oil pan you could drop the engine pretty low in the frame.

Have you put the accessory drive on the engine yet to check fit? With the engine low in the frame you might have problems with the Corvette's low mount alternator getting it between the frame rails. The narrowest LS accessory drive is from the trucks and you can still run the Corvette intake with a pulley relocation kit, but even with the truck accessories you can't mount a stock AC compressor down low and clear the frame rails.

I modified my firewall to allow my LS motor's valve covers to fit about an inch and a half in back of the sheet metal, but I was still surprised how little room I had for an intake tract between the TB and the fan shroud. If I ever do a LS in one of these trucks again, I'll make sure I can get the intake/MAF and filter to fit well before I weld in the motor mounts by mounting the radiator/shroud and support for mockup too
e015475 is offline   Reply With Quote
Old 09-22-2022, 05:51 PM   #19
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

Quote:
Originally Posted by e015475 View Post
I'd think with a Corvette bat-wing oil pan you could drop the engine pretty low in the frame.

Have you put the accessory drive on the engine yet to check fit? With the engine low in the frame you might have problems with the Corvette's low mount alternator getting it between the frame rails. The narrowest LS accessory drive is from the trucks and you can still run the Corvette intake with a pulley relocation kit, but even with the truck accessories you can't mount a stock AC compressor down low and clear the frame rails.

I modified my firewall to allow my LS motor's valve covers to fit about an inch and a half in back of the sheet metal, but I was still surprised how little room I had for an intake tract between the TB and the fan shroud. If I ever do a LS in one of these trucks again, I'll make sure I can get the intake/MAF and filter to fit well before I weld in the motor mounts by mounting the radiator/shroud and support for mockup too
All good points, I need to drop the cab on and look at the accessories thanks
csmeutah is offline   Reply With Quote
Old 07-01-2024, 12:17 PM   #20
csmeutah
Registered User
 
Join Date: Jun 2013
Location: American Fork, Utah
Posts: 33
Re: 1952 Pickup Street Rod project

So, I know I have been negligent in my progress but in the last two years I've had to remodel (new wiring/plumbing kitchen) two apartments, built an electric Vespa conversion, built a smoker and acquired a '50 Chevy COE which I'm switching to so I can haul this truck around. Would this forum be willing to let me post the COE build here?
csmeutah is offline   Reply With Quote
Old 07-01-2024, 08:19 PM   #21
Rickysnickers
Senior Member

 
Join Date: Oct 2014
Location: Eagle, ID
Posts: 3,025
Re: 1952 Pickup Street Rod project

Quote:
Originally Posted by csmeutah View Post
So, I know I have been negligent in my progress but in the last two years I've had to remodel (new wiring/plumbing kitchen) two apartments, built an electric Vespa conversion, built a smoker and acquired a '50 Chevy COE which I'm switching to so I can haul this truck around. Would this forum be willing to let me post the COE build here?
Yes. Start a new build thread here, https://67-72chevytrucks.com/vboard/...play.php?f=205
Rickysnickers is offline   Reply With Quote
Old 07-01-2024, 12:21 PM   #22
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,197
Re: 1952 Pickup Street Rod project

I think you just start a new thread with that title.
dsraven is offline   Reply With Quote
Old 07-01-2024, 08:23 PM   #23
nvrdone
Registered User
 
Join Date: Dec 2011
Location: Moxee WA
Posts: 1,479
Re: 1952 Pickup Street Rod project

There have been a number of COE's posted on here.
__________________
49 chevy 3100 3 window. 327 / m21 4 spd, 12 bolt w/ 3:55's
Bought in 1973 for $235.00. Had it longer than my wife & Kids!!
nvrdone is offline   Reply With Quote
Reply

Bookmarks

Tags
1953, corvette, flatout, ls1, streetrod


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:41 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com