Budget Build 1985 K20 - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

JJH Jimmy · 02-14-2021, 07:20 PM

Quote:

Originally Posted by Katrina/10

I just did the same thing with a speaker hole and got lots of warpage. Had to cut it out and do it over.

Silicon bronze filler wire helps but it is not fool proof. It still takes a fair amount of hammer, dolly and a shrinking disk to get them some what straight.

LT7A · 02-13-2021, 06:23 PM

Wow, you really are taking the time to make it nice. Great work saving on that rig. Glad to see the progress.

JJH Jimmy · 02-14-2021, 07:21 PM

Quote:

Originally Posted by Greenlee

Nice work!

Quote:

Originally Posted by LT7A

Wow, you really are taking the time to make it nice. Great work saving on that rig. Glad to see the progress.

Thanks guys!

JJH Jimmy · 02-14-2021, 07:27 PM

I built a cart for the cab and I made it so it will roll over my motorcycle lift to save my back! I also made removable arms for it so I can flip it on its back for all the work on the bottom side.

JJH Jimmy · 02-14-2021, 07:32 PM

I ordered some GMT400 cab lights and drilled some holes. I will be using rubber well nuts to hold them on.

JJH Jimmy · 02-14-2021, 07:39 PM

Patched a antenna hole in the roof and the clutch master cylinder hole in the firewall.

legendman · 02-22-2021, 07:07 AM

Nice work on this truck !!

JJH Jimmy · 02-22-2021, 12:06 PM

Quote:

Originally Posted by legendman

Nice work on this truck !!

Thank you!

JJH Jimmy · 02-22-2021, 12:31 PM

My OCD kicked in and i had to redo the passenger side cab corner. I replaced the cab corners in the fall when the cab was still on the frame and the drivers side fit like a glove. But the passenger side it was almost like the cab corner was too wide so I just re bent the edge where it meets the door frame. I wasn't happy with it because the edge i bent didn't have the same radius and was going to need filler. So what the hell $20.00 and a weekend of work!

I first cut the new patch to size and measured how much needed to come off. I then cut about 1 /4" off it and welded it back together and metal finished it.

JJH Jimmy · 02-22-2021, 12:36 PM

I then blasted and epoxied the inside of the cab corner and inner cab corner.

JJH Jimmy · 02-22-2021, 12:43 PM

The only thing left is to weld it on and metal finish the welds. It turned out great but what a pain in the butt.

LT7A · 04-06-2021, 04:15 AM

Good progress. It looks like the raptor liner layer out nicely.

JJH Jimmy · 04-16-2021, 08:48 PM

Quote:

Originally Posted by LT7A

Good progress. It looks like the raptor liner layer out nicely.

Yea it did. Thanks. I am afraid that progress is going to slow down. I got a ton of spring cores around the house to get done.

JJH Jimmy · 04-16-2021, 08:55 PM

I did get all the body work on the cab done and into 2k primer. Like everything on this truck way more small dents than anticipated. It appeared someone sat on the roof at some point!

JJH Jimmy · 04-16-2021, 09:01 PM

I also ordered my clear coat and base. It took me forever to decide what SPI clear coat to go with but I finally settled on the Euro over the universal. This is what $1,200 looks like and I’m not sure if it will be enough for the whole truck!

Greenlee · 04-16-2021, 09:11 PM

Nice work! Yep, looks like a butt size dent.

OutlawDrifter · 04-22-2021, 01:11 PM

Awesome work, just joining the build!

This K20 is going to be too nice to drive when you're done!

I'm a big fan of Raptor Liner, I've been using it for about 10 years.

JJH Jimmy · 04-24-2021, 07:45 PM

Quote:

Originally Posted by Greenlee

Nice work! Yep, looks like a butt size dent.

Thanks!

Quote:

Originally Posted by OutlawDrifter

Awesome work, just joining the build!

This K20 is going to be too nice to drive when you're done!

I'm a big fan of Raptor Liner, I've been using it for about 10 years.

Thank you! I hope it not to nice to drive but it’s heading in that direction.

JJH Jimmy · 04-24-2021, 07:56 PM

I tested out the base and clear on the glove box door, ash tray, lower column cover, door have hinges, tailgate hardware and bolts. Everything turned out great. Now it’s time for some bigger pieces.

Greenlee · 04-24-2021, 11:17 PM

Looks great!

OutlawDrifter · 04-24-2021, 11:23 PM

Nice work!

JJH Jimmy · 04-27-2021, 09:11 PM

Fenders, cowl and bumper filler block to 400, washed masked then sealer.

JJH Jimmy · 04-27-2021, 09:22 PM

3 coats of 029 midnight blue base and 4 coats of euro clear. Turned out really nice. A little bit of dust nibs in the clear that I will need to sand out and just a touch of orange peel. I think a quick buff and onto the doors!

OutlawDrifter · 04-27-2021, 09:39 PM

Looks good!

**LEEVON** · 04-28-2021, 03:00 PM

Love the midnight blue, glad you went that route!

02-13-2021, 06:23 PM	#2
LT7A Registered User Join Date: Oct 2015 Location: PNW Posts: 3,615	Re: Budget Build 1985 K20 Wow, you really are taking the time to make it nice. Great work saving on that rig. Glad to see the progress.

02-14-2021, 07:27 PM	#4
JJH Jimmy Registered User Join Date: Jun 2012 Location: Schoolcraft, Michigan Posts: 928	Re: Budget Build 1985 K20 I built a cart for the cab and I made it so it will roll over my motorcycle lift to save my back! I also made removable arms for it so I can flip it on its back for all the work on the bottom side. Attached Images __________________ 1972 GMC Jimmy 4x4 LS Swap 1985 Chevy K20 1994 GMC Yukon 2021 GMC 2500HD Duramax AT4 My "It's a Jimmy Thing" Build http://67-72chevytrucks.com/vboard/s...d.php?t=583528 Budget Build 1985 K20 http://67-72chevytrucks.com/vboard/s...d.php?t=801565

02-14-2021, 07:32 PM	#5
JJH Jimmy Registered User Join Date: Jun 2012 Location: Schoolcraft, Michigan Posts: 928	Re: Budget Build 1985 K20 I ordered some GMT400 cab lights and drilled some holes. I will be using rubber well nuts to hold them on. Attached Images __________________ 1972 GMC Jimmy 4x4 LS Swap 1985 Chevy K20 1994 GMC Yukon 2021 GMC 2500HD Duramax AT4 My "It's a Jimmy Thing" Build http://67-72chevytrucks.com/vboard/s...d.php?t=583528 Budget Build 1985 K20 http://67-72chevytrucks.com/vboard/s...d.php?t=801565

02-14-2021, 07:39 PM	#6
JJH Jimmy Registered User Join Date: Jun 2012 Location: Schoolcraft, Michigan Posts: 928	Re: Budget Build 1985 K20 Patched a antenna hole in the roof and the clutch master cylinder hole in the firewall. Attached Images __________________ 1972 GMC Jimmy 4x4 LS Swap 1985 Chevy K20 1994 GMC Yukon 2021 GMC 2500HD Duramax AT4 My "It's a Jimmy Thing" Build http://67-72chevytrucks.com/vboard/s...d.php?t=583528 Budget Build 1985 K20 http://67-72chevytrucks.com/vboard/s...d.php?t=801565

02-22-2021, 12:31 PM	#9
JJH Jimmy Registered User Join Date: Jun 2012 Location: Schoolcraft, Michigan Posts: 928	Re: Budget Build 1985 K20 My OCD kicked in and i had to redo the passenger side cab corner. I replaced the cab corners in the fall when the cab was still on the frame and the drivers side fit like a glove. But the passenger side it was almost like the cab corner was too wide so I just re bent the edge where it meets the door frame. I wasn't happy with it because the edge i bent didn't have the same radius and was going to need filler. So what the hell $20.00 and a weekend of work! I first cut the new patch to size and measured how much needed to come off. I then cut about 1 /4" off it and welded it back together and metal finished it. Attached Images __________________ 1972 GMC Jimmy 4x4 LS Swap 1985 Chevy K20 1994 GMC Yukon 2021 GMC 2500HD Duramax AT4 My "It's a Jimmy Thing" Build http://67-72chevytrucks.com/vboard/s...d.php?t=583528 Budget Build 1985 K20 http://67-72chevytrucks.com/vboard/s...d.php?t=801565

02-22-2021, 12:36 PM	#10
JJH Jimmy Registered User Join Date: Jun 2012 Location: Schoolcraft, Michigan Posts: 928	Re: Budget Build 1985 K20 I then blasted and epoxied the inside of the cab corner and inner cab corner. Attached Images __________________ 1972 GMC Jimmy 4x4 LS Swap 1985 Chevy K20 1994 GMC Yukon 2021 GMC 2500HD Duramax AT4 My "It's a Jimmy Thing" Build http://67-72chevytrucks.com/vboard/s...d.php?t=583528 Budget Build 1985 K20 http://67-72chevytrucks.com/vboard/s...d.php?t=801565

02-22-2021, 12:43 PM	#11
JJH Jimmy Registered User Join Date: Jun 2012 Location: Schoolcraft, Michigan Posts: 928	Re: Budget Build 1985 K20 The only thing left is to weld it on and metal finish the welds. It turned out great but what a pain in the butt. Attached Images __________________ 1972 GMC Jimmy 4x4 LS Swap 1985 Chevy K20 1994 GMC Yukon 2021 GMC 2500HD Duramax AT4 My "It's a Jimmy Thing" Build http://67-72chevytrucks.com/vboard/s...d.php?t=583528 Budget Build 1985 K20 http://67-72chevytrucks.com/vboard/s...d.php?t=801565

04-06-2021, 04:15 AM	#12
LT7A Registered User Join Date: Oct 2015 Location: PNW Posts: 3,615	Re: Budget Build 1985 K20 Good progress. It looks like the raptor liner layer out nicely.

04-16-2021, 08:55 PM	#14
JJH Jimmy Registered User Join Date: Jun 2012 Location: Schoolcraft, Michigan Posts: 928	Re: Budget Build 1985 K20 I did get all the body work on the cab done and into 2k primer. Like everything on this truck way more small dents than anticipated. It appeared someone sat on the roof at some point! Attached Images __________________ 1972 GMC Jimmy 4x4 LS Swap 1985 Chevy K20 1994 GMC Yukon 2021 GMC 2500HD Duramax AT4 My "It's a Jimmy Thing" Build http://67-72chevytrucks.com/vboard/s...d.php?t=583528 Budget Build 1985 K20 http://67-72chevytrucks.com/vboard/s...d.php?t=801565

04-16-2021, 09:01 PM	#15
JJH Jimmy Registered User Join Date: Jun 2012 Location: Schoolcraft, Michigan Posts: 928	Re: Budget Build 1985 K20 I also ordered my clear coat and base. It took me forever to decide what SPI clear coat to go with but I finally settled on the Euro over the universal. This is what $1,200 looks like and I’m not sure if it will be enough for the whole truck! Attached Images __________________ 1972 GMC Jimmy 4x4 LS Swap 1985 Chevy K20 1994 GMC Yukon 2021 GMC 2500HD Duramax AT4 My "It's a Jimmy Thing" Build http://67-72chevytrucks.com/vboard/s...d.php?t=583528 Budget Build 1985 K20 http://67-72chevytrucks.com/vboard/s...d.php?t=801565

04-16-2021, 09:11 PM	#16
Greenlee Registered User Join Date: Jun 2004 Location: El Lago, TX Posts: 1,668	Re: Budget Build 1985 K20 Nice work! Yep, looks like a butt size dent.

04-22-2021, 01:11 PM	#17
OutlawDrifter Registered User Join Date: Aug 2012 Location: Northeast KS Posts: 1,783	Re: Budget Build 1985 K20 Awesome work, just joining the build! This K20 is going to be too nice to drive when you're done! I'm a big fan of Raptor Liner, I've been using it for about 10 years. __________________ 1999 GMC Suburban K2500 SLT, 454/4L80E 1991 Z/28, 6.0L/T56 1949 GMC 250, S10 Frame, 6.0L/4L80E Instagram @aceshighspeedshop

04-24-2021, 07:56 PM	#19
JJH Jimmy Registered User Join Date: Jun 2012 Location: Schoolcraft, Michigan Posts: 928	Re: Budget Build 1985 K20 I tested out the base and clear on the glove box door, ash tray, lower column cover, door have hinges, tailgate hardware and bolts. Everything turned out great. Now it’s time for some bigger pieces. Attached Images __________________ 1972 GMC Jimmy 4x4 LS Swap 1985 Chevy K20 1994 GMC Yukon 2021 GMC 2500HD Duramax AT4 My "It's a Jimmy Thing" Build http://67-72chevytrucks.com/vboard/s...d.php?t=583528 Budget Build 1985 K20 http://67-72chevytrucks.com/vboard/s...d.php?t=801565

04-24-2021, 11:17 PM	#20
Greenlee Registered User Join Date: Jun 2004 Location: El Lago, TX Posts: 1,668	Re: Budget Build 1985 K20 Looks great!

04-24-2021, 11:23 PM	#21
OutlawDrifter Registered User Join Date: Aug 2012 Location: Northeast KS Posts: 1,783	Re: Budget Build 1985 K20 Nice work! __________________ 1999 GMC Suburban K2500 SLT, 454/4L80E 1991 Z/28, 6.0L/T56 1949 GMC 250, S10 Frame, 6.0L/4L80E Instagram @aceshighspeedshop



Register or Log In To remove these advertisements.

04-27-2021, 09:11 PM	#22
JJH Jimmy Registered User Join Date: Jun 2012 Location: Schoolcraft, Michigan Posts: 928	Re: Budget Build 1985 K20 Fenders, cowl and bumper filler block to 400, washed masked then sealer. Attached Images __________________ 1972 GMC Jimmy 4x4 LS Swap 1985 Chevy K20 1994 GMC Yukon 2021 GMC 2500HD Duramax AT4 My "It's a Jimmy Thing" Build http://67-72chevytrucks.com/vboard/s...d.php?t=583528 Budget Build 1985 K20 http://67-72chevytrucks.com/vboard/s...d.php?t=801565

04-27-2021, 09:22 PM	#23
JJH Jimmy Registered User Join Date: Jun 2012 Location: Schoolcraft, Michigan Posts: 928	Re: Budget Build 1985 K20 3 coats of 029 midnight blue base and 4 coats of euro clear. Turned out really nice. A little bit of dust nibs in the clear that I will need to sand out and just a touch of orange peel. I think a quick buff and onto the doors! Attached Images __________________ 1972 GMC Jimmy 4x4 LS Swap 1985 Chevy K20 1994 GMC Yukon 2021 GMC 2500HD Duramax AT4 My "It's a Jimmy Thing" Build http://67-72chevytrucks.com/vboard/s...d.php?t=583528 Budget Build 1985 K20 http://67-72chevytrucks.com/vboard/s...d.php?t=801565

04-27-2021, 09:39 PM	#24
OutlawDrifter Registered User Join Date: Aug 2012 Location: Northeast KS Posts: 1,783	Re: Budget Build 1985 K20 Looks good! __________________ 1999 GMC Suburban K2500 SLT, 454/4L80E 1991 Z/28, 6.0L/T56 1949 GMC 250, S10 Frame, 6.0L/4L80E Instagram @aceshighspeedshop

04-28-2021, 03:00 PM	#25
LEEVON Moderator Join Date: Jul 2006 Location: Ozark, MO Posts: 4,888	Re: Budget Build 1985 K20 Love the midnight blue, glad you went that route! __________________ '20 Silverado Trail Boss ~ '17 Tahoe ~ '79 K15 Sierra Grande ~ '76 Blazer 2wd ~ '71 Cheyenne swb ~ '55 Pontiac Safari ~'50 3100 bagged ~ '80 Wife ~ Late model kids

Register or Log In To remove these advertisements.