The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-20-2018, 11:27 PM   #1
tommy3horse
Registered User
 
tommy3horse's Avatar
 
Join Date: Feb 2015
Location: St. Clair, Missouri
Posts: 124
Re: What did you do to your truck today.The 3rd chapter

Took my 17yr old out for a cruise around town. JJDa Boss and his his gang are here and all the po-po are there. I think i surprised the boy by laying rubber and making a lil too much noise...in the middle of town, sounded great.
Tom
__________________
1972 GMC C1500 350/350

1965 Mustang 2+2 289 4spd, show-car
1965 Mustang Coupe 289 4spd, stoplight racer
1/2 dozen Wheelhorse Tractors
tommy3horse is online now   Reply With Quote
Old 10-22-2018, 09:59 PM   #2
Steeveedee
Who Changed This?
 
Steeveedee's Avatar
 
Join Date: Jan 2013
Location: Simi Valley, CA
Posts: 10,598
Re: What did you do to your truck today.The 3rd chapter

Put the new Cold Case radiator in. I've had heating problems with the 4-row brass radiator, even after flushing the snot out of it. I put the thing in and couldn't get the lower trans cooler line fitting installed to save my life. Took it back out and realized that the threads on those internal fittings were scrofulous. Brushed all the crud out, put the thing back in and the fittings threaded right in. Finished up, and went to buy a new burp bottle. Once I get it all sealed up, I'll drive it and make sure there are no leaks. Then...put in new coolant. Replaced the old heater control valve while I was at it. My FiL had installed shutoff valves like you see under the sink in one of the lines. I removed it for the flushing process, and was happy to see that the heater core didn't leak. I don't think that it is original. At least I hope not.

Next, I'll be rebuilding the alternator. The front bearing is chuckling, and I don't know if it has ever been rebuilt.

ETA- Took the truck to a steep hill and ran it up to 75 MPH. It's only 78º out, but the gauge stayed right at 190º, which is what the thermostat is rated at. Shut it off, let the temp climb while I was in buying Lottery tickets. Fired it up and it dropped right back down to 190º within a block. Problem fixed. Of course, this doesn't prove it will run cooler when towing the trailer in 100º weather. This truck always ran hot even with a new 4-row brass radiator. Anyone want to buy a used 4-row brass radiator cheap?
__________________
~Steven

'70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper

Simi Valley, CA

Last edited by Steeveedee; 10-23-2018 at 06:22 PM. Reason: info about better cooling
Steeveedee is offline   Reply With Quote
Old 10-27-2018, 03:47 PM   #3
RodnRudy
Senior Member
 
RodnRudy's Avatar
 
Join Date: Oct 2014
Location: New Palestine In
Posts: 931
Re: What did you do to your truck today.The 3rd chapter

I replaced the drivers side valve cover gasket. It was leaking at the bottom rear and the oil tracked down to the flex plate cover and dripped on the floor. I used Fel Pro gasket and Permatex Ultra Gray sealer. Hope this did the trick, I'll know tomorrow when I test drive her.
Attached Images
  
__________________
Phil
"Money is only a tool to create and achieve what you want most in life"
PayPal: rodnrudy@comcast.net
RodnRudy is offline   Reply With Quote
Old 10-28-2018, 06:32 PM   #4
NoStopN
Registered User
 
NoStopN's Avatar
 
Join Date: Jul 2016
Location: Murfreesboro, TN
Posts: 229
Re: What did you do to your truck today.The 3rd chapter

I planned to put the tail lights & reverse light in my donor bed, but I realized that I didn't have the screws needed to hold them to the bed. Does anyone know the thread pitch of screws that I'll need?

With the first item on hold, I moved back to the last unfinished step. I got the bed lined up & bolted down, followed by the bed side to floor bolts that I could get in. Surprisingly, only 1 had to be left out. So, at least the bed won't rattle or fly off. But there won't be enough speed to make that happen if I don't have brake lights, turn signals, etc. Today was still progress, so it's all good.
__________________
1969 GMC 2500. 250 I6, 4-speed w/ granny low
NoStopN is offline   Reply With Quote
Old 10-28-2018, 06:53 PM   #5
yuccales
Registered User
 
yuccales's Avatar
 
Join Date: May 2011
Location: Northern Calif.
Posts: 3,751
Re: What did you do to your truck today.The 3rd chapter

Dump trip this morning. Wash and vacuum, tire rotate afterwards.
yuccales is offline   Reply With Quote
Old 10-28-2018, 07:35 PM   #6
CarolinaHD
Moderator
 
CarolinaHD's Avatar
 
Join Date: Aug 2017
Location: Cabarrus
Posts: 417
Re: What did you do to your truck today.The 3rd chapter

Got the 67 running and moving! Ran it up and down the driveway a few times and it should make the 10 mile trip to the new house this week.

Slid the rear axle under the 06 to move onto the trailer

Oil change and tire rotation for the Tahoe
Attached Images
 
__________________
Alex
1967 C50 292ci Lumber truck
1967 C50 292ci Dump truck
1967 C60 366ci Fire truck
CarolinaHD is offline   Reply With Quote
Old 10-28-2018, 08:02 PM   #7
Steeveedee
Who Changed This?
 
Steeveedee's Avatar
 
Join Date: Jan 2013
Location: Simi Valley, CA
Posts: 10,598
Re: What did you do to your truck today.The 3rd chapter

Pulled the alternator because the front bearing is noisy. It's been on there for a donkey's years. I couldn't get the rotor out of the front bearing. I'll just get a rebuilt one tomorrow. Turns out that it isn't the original, anyway. I wanted to rebuild it, they're easy (if you can get them apart).
__________________
~Steven

'70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper

Simi Valley, CA
Steeveedee is offline   Reply With Quote
Old 11-05-2018, 06:39 AM   #8
72freak
Rottenwood Garage Member
 
72freak's Avatar
 
Join Date: May 2005
Location: Marietta, Georgia
Posts: 4,321
Re: What did you do to your truck today.The 3rd chapter

Drove it!
Attached Images
  
__________________
2004 Chevrolet Suburban C1500
2001 Chevrolet 2500HD Crew 6.0
1999 Harley Davidson Electra Glide
1972 Chevrolet C-20 Custom Camper "Dump Truck"
1972 Chevrolet C-20 Suburban "Big Green"
1969 Chevrolet C-50 Wedge Hauler "Leonidis"
1966 C-10 2x4 short fleet 327 4 speed "Race Truck"
1952 Plymouth Cranbrook "Rican" (my grandfathers)
1931 Ford Model A Coupe "Black Beauty"
1930 Ford Model A truck "Club Cab" 4x4


Rottenwood Garage and Speed Shop.....where everything must be racy!

It's not just a hobby..It's a LIFESTYLE!!!

Thanks for nothing Barrett-Jackson

You cant fix stupid or teach accountability!


Time wasters, looky Lous and tire kickers are everywhere!
72freak is offline   Reply With Quote
Old 11-29-2018, 11:02 PM   #9
j286
Registered User
 
Join Date: Jul 2017
Location: oakdale
Posts: 26
Re: What did you do to your truck today.The 3rd chapter

Working on filler panels!
Attached Images
 
j286 is offline   Reply With Quote
Old 01-06-2019, 07:22 AM   #10
88Stanger
Registered User
 
88Stanger's Avatar
 
Join Date: Mar 2015
Location: Washington State
Posts: 1,651
Re: What did you do to your truck today.The 3rd chapter

moved the coil packs
Attached Images
  
88Stanger is offline   Reply With Quote
Old 01-06-2019, 04:28 PM   #11
JerryIndy2112
Registered User
 
JerryIndy2112's Avatar
 
Join Date: Nov 2018
Location: Indianapolis
Posts: 130
Re: What did you do to your truck today.The 3rd chapter

I pulled my bench seat, removed last of the green shag carpet. So glad that is gone. I vacuumed floorboards. Installed new dome light I got for Christmas. Removed lower part of old door gaskets, they were holding moisture. Removed old stereo amp under the seat.
Attached Images
  
JerryIndy2112 is offline   Reply With Quote
Old 01-06-2019, 07:06 PM   #12
RodnRudy
Senior Member
 
RodnRudy's Avatar
 
Join Date: Oct 2014
Location: New Palestine In
Posts: 931
Re: What did you do to your truck today.The 3rd chapter

I finished up welding up the patch for the ugly speaker hole in the door this afternoon Also I picked up this nice E brake cover at the swap meet this morning. Thanks Todd, nice meeting you.
Attached Images
     
__________________
Phil
"Money is only a tool to create and achieve what you want most in life"
PayPal: rodnrudy@comcast.net
RodnRudy is offline   Reply With Quote
Old 06-30-2019, 08:27 AM   #13
WorkinLonghorn
Senior Member
 
WorkinLonghorn's Avatar
 
Join Date: Dec 2006
Location: Studio City, Calif.
Posts: 2,883
Re: What did you do to your truck today.The 3rd chapter

Got one of my saddle tanks back on-line.



"Fixed" my ancient exhaust system replacing the manifold to pipe brass nuts and changing out the coffee cans that hold the muffler together.

Replaced windshield washer hose but there is not enough pressure to squirt more than a few inches, still not bad for not having worked for 30 years.

Fixed charging system (wire to Ign. Switch came loose). -BA
Attached Images
  
__________________
'69 GMC C2500 Custom Camper, 8 1/2' bed, New GM 350, NP 435 Close Ratio 4spd. Trans., 3.73 Dana-60 open.Camper and Trailer wiring, PS, PB, AC, tach , three gas tanks, stereo speakers, 2nd owner, Work-Truck supreme.
WorkinLonghorn is offline   Reply With Quote
Old 07-02-2019, 12:08 AM   #14
Metaldoc
Registered User
 
Metaldoc's Avatar
 
Join Date: Apr 2015
Location: Ayr Ontario
Posts: 1,122
Re: What did you do to your truck today.The 3rd chapter

Quote:
Originally Posted by WorkinLonghorn View Post
Got one of my saddle tanks back on-line.



"Fixed" my ancient exhaust system replacing the manifold to pipe brass nuts and changing out the coffee cans that hold the muffler together.

Replaced windshield washer hose but there is not enough pressure to squirt more than a few inches, still not bad for not having worked for 30 years.

Fixed charging system (wire to Ign. Switch came loose). -BA
How does the chain saw blade work as a structural support?
__________________
Do it, Do it right, Do it right the first time
Metaldoc is offline   Reply With Quote
Old 07-02-2019, 09:03 AM   #15
WorkinLonghorn
Senior Member
 
WorkinLonghorn's Avatar
 
Join Date: Dec 2006
Location: Studio City, Calif.
Posts: 2,883
Re: What did you do to your truck today.The 3rd chapter

Quote:
Originally Posted by Metaldoc View Post
How does the chain saw blade work as a structural support?
Works great. Was way out in bumfuc and saw that my tank was being supported by the exhaust pipe after the support dropped through the bed wood. So I did what I could. Right now I'm too busy to worry about fixing it the right way (new bed wood). I thought you guys would get a laugh.

Oh, that other "structural support" is a section of 4" plastic bender-board that i sawed a notch in with a carpenters saw.
__________________
'69 GMC C2500 Custom Camper, 8 1/2' bed, New GM 350, NP 435 Close Ratio 4spd. Trans., 3.73 Dana-60 open.Camper and Trailer wiring, PS, PB, AC, tach , three gas tanks, stereo speakers, 2nd owner, Work-Truck supreme.
WorkinLonghorn is offline   Reply With Quote
Old 08-26-2019, 11:31 PM   #16
lintcollector
Registered User
 
Join Date: Sep 2018
Location: West Jordan, UT
Posts: 71
Talking Re: What did you do to your truck today.The 3rd chapter

Took it around the block for the first time ever. Felt GREAT!
__________________
Thx, Lintcollector
'72 C10 Fleetside Big Block

See my build thread here:
http://67-72chevytrucks.com/vboard/s...d.php?t=771552
lintcollector is offline   Reply With Quote
Old 10-02-2019, 09:05 PM   #17
rechinca
Senior Member
 
rechinca's Avatar
 
Join Date: Jul 2018
Location: Vacaville, CA
Posts: 529
Re: What did you do to your truck today.The 3rd chapter

Yep, it just got real, real fun. Half a day of drilling out spotwelds and pulling sheet metal by myself. MIG gas cylinder (75/25) picked up, and just so happened my cab/radiator mounts came in too. I also ordered up the Brother’s radiator support patch. A little pricey, but that thing is really well made and stout. Tomorrow I’ll finish the cuts on the underside of the cowl/dash area and possibly start tacking in my patch pieces.
Attached Images
   
__________________
1971 Custom/10 - 350/3 speed, Orange/White roof
rechinca is offline   Reply With Quote
Old 04-03-2020, 05:19 PM   #18
Daron65
Registered User
 
Join Date: Oct 2019
Location: Monaca, PA Western PA
Posts: 93
Re: What did you do to your truck today.The 3rd chapter

Installed new tarp, finished the duel exhaust. Now relaxing.
Attached Images
 
__________________
1971 Chevrolet C20, Blueprint 355. Holly Street Avenger 430HP. Turbo 350

1952 Chevrolet Deluxe. Stock. True survivor with 1 paint job

1953 Buick Special. GM 355. Just a good smooth engine.
Daron65 is offline   Reply With Quote
Old 06-07-2020, 01:54 PM   #19
BC10
Senior Member
 
BC10's Avatar
 
Join Date: Oct 2013
Location: Bay Area, CA
Posts: 493
Re: What did you do to your truck today.The 3rd chapter

Sand primer, sand primer, sand primer, repeat...
Attached Images
  
BC10 is offline   Reply With Quote
Old 11-11-2020, 02:25 AM   #20
BC10
Senior Member
 
BC10's Avatar
 
Join Date: Oct 2013
Location: Bay Area, CA
Posts: 493
Re: What did you do to your truck today.The 3rd chapter

Finally got to test drive the truck, after installing Redhead steering box. Man, what a difference! Sucker turns quick now.
BC10 is offline   Reply With Quote
Old 01-24-2021, 07:02 PM   #21
BC10
Senior Member
 
BC10's Avatar
 
Join Date: Oct 2013
Location: Bay Area, CA
Posts: 493
Re: What did you do to your truck today.The 3rd chapter

New mufflers installed
Attached Images
 
BC10 is offline   Reply With Quote
Old 01-24-2021, 08:48 PM   #22
Ol Blue K20
Proprietor of Dale's Corner
 
Ol Blue K20's Avatar
 
Join Date: Nov 2012
Location: Vacaville , CA
Posts: 16,243
Re: What did you do to your truck today.The 3rd chapter

Quote:
Originally Posted by BC10 View Post
New mufflers installed
It's gonna have a nice rumble...
__________________
"Some Days Chickens And Some Days Feathers"

Dale
XNGH ECV Sam Brannan 1004

R.I.P. 67ChevyRedneck
R.I.P. Grumpy Old Man
R.I.P. FleetsidePaul
Ol Blue K20 is offline   Reply With Quote
Old 12-27-2022, 01:07 AM   #23
towbar
Registered User
 
towbar's Avatar
 
Join Date: Jul 2012
Location: Marshall, NC....heart of the Appalachians.....aka, Gods country!!
Posts: 537
Re: What did you do to your truck today.The 3rd chapter

inner rocker panel replaced, kick panel replaced, A post repaired , cab corner cut out, new one fitted and ready to weld, inner door bottom replaced, outer lower door skin replaced...still need to fit the outer rocker, replace door to align rocker and cab corner before final welding. Gap the door, then ready for body work. Hopefully will get some of that finished this week
Attached Images
   
towbar is offline   Reply With Quote
Old 10-29-2018, 06:57 PM   #24
66clow
Registered User
 
66clow's Avatar
 
Join Date: Jun 2012
Location: Clearwater Beach Florida
Posts: 872
Re: What did you do to your truck today.The 3rd chapter

Close to having it in one color. And plan to do it in red and white like this one. But my color choices changes day to day.
Attached Images
    

Last edited by 66clow; 10-29-2018 at 07:47 PM.
66clow is offline   Reply With Quote
Old 11-01-2018, 02:53 PM   #25
elorenzof
Registered User
 
Join Date: Nov 2017
Location: Anthem AZ
Posts: 281
Re: What did you do to your truck today.The 3rd chapter

This past weekend I took of the Engine Crossmember and Installed a new freshly coated Crossmember, Upper and Lower Control Arms, New Steering Stuff ie: tie rods, pitman arm, etc... New Drop Spindles with Disc Brake Conversion kit.
Attached Images
  
elorenzof is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:01 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com