IN Fleetside bed floor patch panels

[70STOVEBOLT]

Here are pics of the other 2 pieces.

[70STOVEBOLT]

Originally Posted by DA68

In regard to the patch, a 12"x12" or slightly larger will work.

How many raised ribs do you need? Also, what is your zip code?

[davem815]

Originally Posted by 70STOVEBOLT

Dave, did you get a pic?

I was looking for the end of one rib at the rear of the bed. like this. I'm not sure if there is enough flat around the rib. I will try to get an exact picture of what I need tonight.

[70STOVEBOLT]

Ok, just let me know.

[tallbob]

I could make work a couple of 12"x24" pieces. Size can be approximate,a little wider or longer is fine. Let me know what overall cost looks like with shipping to Greensburg, Pa 15601. Thanks much

[tallbob]

Bigger size patch panels like whats in your pics are fine also,just didnt want to get into oversize shipping charges. Let me know. Thanks again.

[70STOVEBOLT]

tallbob, I can ship you a couple 12 x 24 pieces for $78 shipped via PayPal or $75 shipped with postal money order.

Thanks,
Mark

[tallbob]

OK I will take them. I would prefer to do PayPal. How about sending me a PM with your info and I will follow thru. Thanks much.

[70STOVEBOLT]

Ok, PM sent

[70STOVEBOLT]

Still have some good patches left.

[DA68]

I just need a good, straight 12" x 12" or so patch. Zip code is 44011. Thanks.

[70STOVEBOLT]

$31 shipped, I can cut one tonight and ship it tomorrow. PM sent with payment info.

Thanks,
Mark

[tallbob]

Mark,
I recieved the two panels you sent. I may need another piece or two. I should know over the weekend. Keep me in mind. What do you have left?
Thanks much,
Bob

[70STOVEBOLT]

Bob, I still have 2 of the larger pieces and some smaller (approx 12 x 12) pieces as well. Let me know what you need. I need to get some better blades for the sawzall. The ones I used were not made for sheet metal and they made it hard to cut a straight line. I am going to pick up some sheet metal cutting blades and I should be able to make better cuts.

[tallbob]

Mark,
Looks like I could use 2 more floor pieces, Same size as before if you have them, approximately 12"x24". Let me know what you have? Thanks again,
Bob

[70STOVEBOLT]

Bob, I will take a look tonight and let you know. I think I have two more.

[70STOVEBOLT]

Bob, I should be able to come up with 2 more panels.

[tallbob]

Mark,
Thats great. Are they both about the same size as the previous two + or - ?
Let me know when you are ready to ship? Thanks, Bob

[70STOVEBOLT]

Bob, I will get them cut tomorrow and can ship on Monday. Don't send money yet as I did not measure the pieces I have left but I am confident I can come up with about the same sizes.

[70STOVEBOLT]

Bob will this piece work for you? I only have one good middle floor section in the size you need. This is the rear of the floor.

[tallbob]

Mark,
Yes they will work for my needs. Especially the rear section. Let me know when you are good on your end and I will go from there. Thanks

[70STOVEBOLT]

Bob, after looking closer at this one section, I noticed it has some pitting. It is solid metal but it has some pits. Let me know if you still want it, here is a close up pic. This would be about a 6" x 6" area at the corner of one panel.

[tallbob]

Mark,
I don't think the small pits will be to big a deal. How about sending me a PM on what you are thinking price wise and we can go from there? Thanks much,
Bob

[70STOVEBOLT]

PM sent

[jessemthompson]

I missed your reply to my post and haven’t been active as of late. Looking for around an 8X8 piece. Just need it to run across 3 ribs evenly shipped to 28376. Thanks