![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#26 |
Registered User
Join Date: Jan 2013
Location: Las Vegas, NV
Posts: 1,853
|
Re: 62' c10 V8 motor mount help
I didn't have to. But seams alot did.
__________________
1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081 |
![]() |
![]() |
![]() |
#27 |
60-66 Nut
![]() ![]() Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 23,248
|
Re: 62' c10 V8 motor mount help
I agree that you shouldn't have to. Worst case, I don't see the need for a spacer more than say 1/4". The reason that I recommend the '67-'72 small block frame brackets is that they fit the '60-'62 frames quite nicely. Much better than the '63-'66 or '67-'72 230/250 I6 brackets.
__________________
Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE |
![]() |
![]() |
![]() |
#28 |
Senior Enthusiast
Join Date: Feb 2007
Location: Spokane Valley, WA
Posts: 8,356
|
Re: 62' c10 V8 motor mount help
I needed the 1" spacers on mine. They are shown in the following thread:
http://67-72chevytrucks.com/vboard/s...d.php?t=369663
__________________
My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=444502 |
![]() |
![]() |
![]() |
#29 |
Registered User
Join Date: Aug 2006
Location: Athens, Georgia
Posts: 1,456
|
Re: 62' c10 V8 motor mount help
So if I'm reading all this correctly, it breaks down like this:
'60-'62 Frame w/ Original torsion bar crossmember: factory '67-'72 small block mounts, bolt-on, no spacers needed. '60-'62 Frame w/ Later '63-up coil spring crossmember: '67-'72 small block mounts, require spacer blocks between top of frame and engine mount stand. Is that correct?
__________________
'61 Suburban daily driver: off the road due to 180-pound 8-pt buck! '62 K-10 long-step project '61 C30 Camper, aka "Valdez" There's no cool like Old School |
![]() |
![]() |
![]() |
#30 |
Senior Enthusiast
Join Date: Feb 2007
Location: Spokane Valley, WA
Posts: 8,356
|
Re: 62' c10 V8 motor mount help
I can only speak for my own truck, and I needed the spacers both for the original crossmember and again when I swapped in the 1973 front suspension.
__________________
My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=444502 |
![]() |
![]() |
![]() |
#31 |
Registered User
Join Date: Feb 2008
Location: Sidney,b.c.
Posts: 4,425
|
Re: 62' c10 V8 motor mount help
http://www.persh.org/pickup/perches.htm
this even shows some orig sbc side mounts for 60/62 and the next link is for rear trans c/member http://www.persh.org/pickup/700R4.htm ron |
![]() |
![]() |
![]() |
#32 |
Registered User
Join Date: Jan 2014
Location: Rock Hill SC
Posts: 156
|
Re: 62' c10 V8 motor mount help
Thanks for the info guys! I'm still searching for that other motor mount, but might just buy some new ones, although, I don't think anyone makes a new set do they?
Padresag, I will have to look at those links when I get home since I'm at work, they are blocked ![]() |
![]() |
![]() |
![]() |
Bookmarks |
|
|