![]() |
![]() |
#26 |
Registered User
Join Date: Apr 2011
Location: San Diego CA
Posts: 241
|
Re: What Did You Do With Your Truck Today ?
I finished mounting the new gas tank between the frame rails. Just need to plumb it and decide if I'm going to a electric fuel pump.
![]() |
![]() |
![]() |
#27 |
Registered User
Join Date: Oct 2010
Location: WI
Posts: 347
|
Re: What Did You Do With Your Truck Today ?
Drove it 15 miles to work this morning. Drove it yesterday too.
|
![]() |
![]() |
#28 |
Registered User
Join Date: Jul 2011
Location: Las Vegas - Nev. aka Sin City
Posts: 1,835
|
Re: What Did You Do With Your Truck Today ?
nice work on the repatching
|
![]() |
![]() |
#29 |
Registered User
Join Date: Dec 2009
Location: Melbourne Australia
Posts: 549
|
Re: What Did You Do With Your Truck Today ?
Just got my frame back from the sand blaster, after blowing off the excess sand & a quick prepsol wipe down my work colleague hit it with LIC industrial low gloss 2K.
|
![]() |
![]() |
#30 |
Registered User
Join Date: Oct 2007
Location: kearney nebraska
Posts: 221
|
Re: What Did You Do With Your Truck Today ?
|
![]() |
![]() |
#31 |
Registered User
Join Date: Aug 2011
Location: australia
Posts: 22
|
Re: What Did You Do With Your Truck Today ?
DUWAM, you win, that's what it is it all about, driving your car.
I miss my '37 chev sedan, that was a daily. Oh well, got to get the '48 pickup finished. Bryan |
![]() |
![]() |
#32 |
Registered User
Join Date: Sep 2009
Location: Monroe,Iowa
Posts: 4,370
|
Re: What Did You Do With Your Truck Today ?
Red Foreman,Your frame is looking great!!! Are you going to start a build thread?
|
![]() |
![]() |
#33 |
Registered User
Join Date: Jul 2011
Location: Auburn ca.
Posts: 2,886
|
Re: What Did You Do With Your Truck Today ?
I painted my steering column parts.
|
![]() |
![]() |
#34 |
Registered User
Join Date: Aug 2011
Location: phoenix az
Posts: 723
|
Re: What Did You Do With Your Truck Today ?
I fabricated all but one of my hydroboost lines. The left frame rail is getting really busy. I finally found adapters to install the proportioning valve, and installed clamps for the brake lines.
Now if I can just find a rebuild kit for the master cyl. I can finish assembling that. Bought the firewall paint and talked to the painter about fenders and inner fenders. Looks like I need to get a few parts stripped. |
![]() |
![]() |
#35 |
Registered User
Join Date: Aug 2010
Location: West Kelowna, BC
Posts: 488
|
Re: What Did You Do With Your Truck Today ?
Red Forman: lookin good
![]() |
![]() |
![]() |
#36 |
Registered User
Join Date: Dec 2009
Location: Melbourne Australia
Posts: 549
|
Re: What Did You Do With Your Truck Today ?
|
![]() |
![]() |
#37 |
Registered User
Join Date: Dec 2010
Location: Caddo Oklahoma
Posts: 164
|
Re: What Did You Do With Your Truck Today ?
Did not do anything with my truck today, but I worked on my car hauler so I can take the frame to my buddies shop to put on his rotisserie to finish welding in Malibu clip.
__________________
My Build Thread 51 chevy http://67-72chevytrucks.com/vboard/s...d.php?t=437496 48,49,50 Chevy trucks. 41 Olds |
![]() |
![]() |
#38 |
Registered User
Join Date: Apr 2011
Location: San Diego CA
Posts: 241
|
Re: What Did You Do With Your Truck Today ?
I sourced the cross sill material for the flatbed build. Feeling pretty sure about major progress this weekend.
|
![]() |
![]() |
#39 |
Registered User
Join Date: Jul 2011
Location: Auburn ca.
Posts: 2,886
|
Re: What Did You Do With Your Truck Today ?
I painted the rest of my steering column parts and measured and measured and oh yeah measured again for rear suspension placement.
|
![]() |
![]() |
#40 |
Registered User
Join Date: May 2010
Location: Lawrenceville, Ga
Posts: 2,646
|
Re: What Did You Do With Your Truck Today ?
Got my cluster, new ignition switch, light switch, and electric wipers installed, got most of my under-dash wiring done. I'm not using a late GM steering column like the EZ-Wire harness is designed for so it's going a little slower than I wanted.
What does the "lock" position on the ignition bezel do? New ignition switch, key turns backward to what I thought was accessory position, but bezel says "lock". and no power to accessories in that position. |
![]() |
![]() |
#41 |
Registered User
Join Date: Apr 2010
Location: Granbury ,TX
Posts: 268
|
Re: What Did You Do With Your Truck Today ?
|
![]() |
![]() |
#42 |
Registered User
Join Date: Dec 2002
Location: Cactus Patch So. Az
Posts: 4,749
|
Re: What Did You Do With Your Truck Today ?
Fixed the gas pedel where the rod goes theu the floor and carpet and I think I gained at least 50 more HP at WOT !!
__________________
53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42 |
![]() |
![]() |
#43 |
Registered User
Join Date: Sep 2011
Location: Golden Valley,MN
Posts: 639
|
Re: What Did You Do With Your Truck Today ?
Worked on straightening the right rear fender...loaded right front fender into my suburban to bring to work tomorrow to see if I can "adapt" a BMW HID headlamp to work in my 1951 pick-up!
|
![]() |
![]() |
#44 |
Registered User
Join Date: Sep 2011
Location: Southaven,MS
Posts: 39
|
Re: What Did You Do With Your Truck Today ?
dropped off my new steelies at the powdercoaters
|
![]() |
![]() |
#45 |
Registered User
Join Date: Aug 2011
Location: phoenix az
Posts: 723
|
Re: What Did You Do With Your Truck Today ?
Russell, it usually means that you have a passenger car ignition switch instead of a truck unit.
The problem is that some money grubbing soul determined that they were interchangeable, and the truck units don't seem to be getting reproduced anymore, yielding our plastic ignition switch placards incorrect for the switch. I don't think the passenger car position indicators match very well, which is why I stubbornly installe a brand new truck plastic piece on my brand new passenger car ignition switch on my '57 truck. Anyway, I sanded my firewall for a couple hours, and got really bored with that, and painted it anyway. You can't see where I stopped sanding, because Iadded some hardener/accelerator to the paint and it kicked pretty fast so I hand buffed it at the sanding edge, so that is good. Someday, I will get it painte right. It looks nice with fresh paint under the hood. I blasted the inner fender panels and used a file to clean up the area where I used the die grinder to open them up to clear the upper control arms. It appears someone cut them with tin snips while they were installed to get to the back side of the upper shock absorber bolts. I cut that area out, and will probably add some metal or rubber there. It's coming along.......I got my aluminum water pump today, but unfortunately it isn't much lighter than the cast iron one. I'm still planning on the aluminum heads, aluminum water pump, and aluminum radiator to raise the front up about 1/2"-3/4" to make it look better. Setting the old Iron head engine in it without the bumper and grille made it low, so this can only help. If it doesn't work, I will just have to either go big block springs or have the current ones re-tempered. I bead blasted the horn relay, and it looks new. I am going to use the old original voltage regulator holes to mount a master cylinder reservoir. I now have so many tubes along the left frame rail that it looks like an aircraft wheel well. I am only going to add a fewmore, I need a vent line for the stick portion of the trans and a vent line for the overdrive portion, and master cylinder remote line. Maybe I will run the vents under the bed, or to the right side.I acquired a 2 3/4" big brake set-up for the rear, but the backing plates are so rusty that I should have them either dipped or sand blasted. Since I bought new shoes for the 2 inch brakes, I will run those for a while. I used the spring kits for the big brake set-up on the smaller brakes since it was new. I also cleaned up the area around the truck really good because the Boss was coming back today and he likes a really nice clean facility. The airplane is back, I need to work on it, so no truck work till it leaves again....... Last edited by Coupeguy2001; 09-30-2011 at 02:12 AM. |
![]() |
![]() |
#46 |
Registered User
Join Date: May 2010
Location: Lawrenceville, Ga
Posts: 2,646
|
Re: What Did You Do With Your Truck Today ?
"Russell, it usually means that you have a passenger car ignition switch instead of a truck unit.
The problem is that some money grubbing soul determined that they were interchangeable, and the truck units don't seem to be getting reproduced anymore, yielding our plastic ignition switch placards incorrect for the switch. I don't think the passenger car position indicators match very well, which is why I stubbornly installe a brand new truck plastic piece on my brand new passenger car ignition switch on my '57 truck." Now I remember. I had forgotten about Chevie's having that style ignition. Since I already had the bezel with "lock" printed on it and since my new switch was actually a car switch anyway I went back over to the Classic Chevy parts store and got a car tumbler. I like it. In case anyone didn't know this, you can remove the key when it's in the "off" position and start the vehicle using the knob. The "lock" position locks it. |
![]() |
![]() |
#47 |
Registered User
Join Date: Dec 2009
Location: Ventura, Ca.
Posts: 439
|
Re: What Did You Do With Your Truck Today ?
poured an adult beverage and wire wheeled brake parts... maybe paint them tomorrow...
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=385404 |
![]() |
![]() |
#48 |
Registered User
Join Date: Jul 2010
Location: Virginia Beach
Posts: 195
|
Re: What Did You Do With Your Truck Today ?
I drove mine to Lowes to get materials to finish moving in and setting up the garage so I can keep her inside. Along the way I dropped it on the rockers to make a toyota look bad, and beat a mustang light to light because he was a punk and irritated me.
__________________
1958 Fleetside shortbox 1965 Malibu SS 1970 Camaro RS 1972 Malibu wagon |
![]() |
![]() |
#49 |
Registered User
Join Date: Jul 2011
Location: Las Vegas - Nev. aka Sin City
Posts: 1,835
|
Re: What Did You Do With Your Truck Today ?
started hand bending steel fuel line from fuel pump to the carb (i have a hand bender tool but all the bends i mark went the wrong way lol -got pretty close to what i want just gotta tweek it a l'il more. - uncle jack is callin me again
tomorrow is master cylinder day -bench bleed and install - bleed brakes all around 4-5 times .- check that off my list . |
![]() |
![]() |
#50 |
Registered User
Join Date: Jul 2011
Location: Auburn ca.
Posts: 2,886
|
Re: What Did You Do With Your Truck Today ?
Looks like rain so picking up and covering up.
|
![]() |
![]() |
Bookmarks |
|
|