Like I needed another one of these things.... - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

67chevy1series · 03-10-2011, 09:01 PM

sure buy those rims and send me your steelies!

mtm_seven · 03-13-2011, 01:27 AM

Weekend update from M7:

Added a Lokar shift linkage, swapped the rear bumper from my Blazer, transmission fluid change, new water pump, swapped new-to-me eyebrows, chopped off rear exit exhaust, removed heater plenum and associated junk, aligned the grille shell, added new beefy ground straps to engine / cab, replaced pitman arm and did a CLR trial run on the paint patina. I'm taking Sunday off because I'm tired.

**FRENCHBLUE72** · 03-13-2011, 01:37 AM

Truck is really comming along nice work..

Longhorn Man · 03-13-2011, 08:57 AM

the CLR thing is pretty cool huh?
Truck is lookin bad ass!

mtm_seven · 03-20-2011, 02:10 PM

Smurftastic.

mtm_seven · 03-29-2011, 10:38 AM

Here are the embarrassing before pics of the rusty floor areas. One spot under the cowl needs attention as well.

I have since plasma'd out a few spots and sprayed it all with ospho for rust treatment. Before the rockers can go on I'll have to repair the cab supports which means removing the clip. If the clip is off then might as well remove the motor / transmission and so forth.... ugh.

mtm_seven · 03-29-2011, 10:39 AM

More:

mtm_seven · 03-29-2011, 10:41 AM

Oh and I am not the hack that removed the rockers in such a sloppy manner. :/

1LoC10 · 03-29-2011, 10:50 AM

cool truck

mtm_seven · 07-25-2011, 10:53 AM

My floorboard rust repairs are almost done - just need to pull the front clip, replace the pass lower pillar support and weld in the passenger rocker panel.

I went ahead and laid down some rust cap paint, then seam sealer then topped it all with sound deadener. It runs from the cowl all the way to the line just below the upper gas tank mounts. Already a vast improvement over the rattles and engine noise.

I have carpet, new door felts and floor vent seals to install next - Hopefully it'll be tight enough to keep the dirt dobbers out of there while it sits around waiting to be worked on.

mtm_seven · 08-08-2011, 10:56 AM

Floor repairs finished
rockers on
encapsulator painted top, bottom, cowl and inside doors
seam sealed floors and cowl
installed new felts and door rubber
slapped on door panels / arm rests
refurbished the floor vents

I like how the doors close now.

Here's a video of an open / shut:
http://tinyurl.com/3s88hyk

o6r1man · 08-08-2011, 11:50 AM

LOOKING GOOD!!!! I wish had a truck that nice to start with.

33shooter · 08-08-2011, 01:22 PM

Looking good! I like the stance. Austin huh....I'll see you around I hope.

72Horn1Ton · 08-08-2011, 07:53 PM

I may have a fairly good front bumper.

VA72C10 · 08-08-2011, 09:01 PM

Nice progress!!!

sean1969c10 · 08-08-2011, 09:46 PM

Looking good!!!!

mtm_seven · 08-13-2011, 07:42 PM

Made a a tad more progress today -

•primed my drip rail (seam seal tomorrow)
•added a transmission mount (PO had a chunk of 2" square tubing in there instead)
•touched up other seam seal areas underneath
•added my new to me GMC fender emblems
•took some current pics

I also found some rebuilt 062 vortec heads on craigslist that I'm thinking about buying myself for my birthday.... Then I can install the Edelbrock fuel injection, serpentine setup, 700-r4 and other goodies that I've got waiting for deployment.

Too bad I can't do *this* 5 days a week and sit in a cube for 2.

mtm_seven · 12-04-2011, 12:53 AM

Update:

Pulled the front and rear glass to touch up the seams and add CST trim. The dash is sanded and cleared to give the worn look that the outside has - maybe a tad too far but I can always cover it later.... Whatchu think?

Glass install was less than smooth but it's at least done now. Thank goodness this is a patina truck and not a show truck or I'd be in jail for breaking the fingers of the install guys. Grr.

mtm_seven · 12-04-2011, 12:54 AM

Oh, and on a side note, the glass guys were EXTREMELY confused at the concept of having a truck all updated underneath with a rusty old faded exterior. (mission accomplished)

mtm_seven · 12-24-2011, 04:08 PM

Picked up a Vortec donor truck this week. Merry Xmas to me!

'98 Suburban 180k with a busted transmission - $1100

I'll vent some holiday aggression on the scrapping process.

black_sheep454 · 12-24-2011, 04:23 PM

Trucks looking awesome, keep up the good work.
Posted via Mobile Device

mtm_seven · 12-24-2011, 04:48 PM

Tow-tow

ChevLoRay · 12-24-2011, 05:36 PM

The burb may have some resale potential on the 88-98 parts board.....

lha1992 · 12-24-2011, 06:38 PM

Please note that you must be a supporting member to post classified items. This includes but is not limited to What Its Worth, Want To Buy, Want To Trade, and For Sale. Please consider supporting the forum by subscribing. Further information on the subscription levels available are located here

If you need any further assistance with that please contact any Admin for help.

chevy88 · 12-24-2011, 11:39 PM

Those rims look really good, and hey I'd love to have a shop that we didnt have to heat all the time.

03-10-2011, 09:01 PM	#26
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: Like I needed another one of these things.... sure buy those rims and send me your steelies!

03-13-2011, 01:27 AM	#27
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... Weekend update from M7: Added a Lokar shift linkage, swapped the rear bumper from my Blazer, transmission fluid change, new water pump, swapped new-to-me eyebrows, chopped off rear exit exhaust, removed heater plenum and associated junk, aligned the grille shell, added new beefy ground straps to engine / cab, replaced pitman arm and did a CLR trial run on the paint patina. I'm taking Sunday off because I'm tired. Attached Images __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

03-13-2011, 01:37 AM	#28
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,604	Re: Like I needed another one of these things.... Truck is really comming along nice work.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

03-13-2011, 08:57 AM	#29
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	Re: Like I needed another one of these things.... the CLR thing is pretty cool huh? Truck is lookin bad ass!

03-20-2011, 02:10 PM	#30
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... Smurftastic. Attached Images __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

03-29-2011, 10:38 AM	#31
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... Here are the embarrassing before pics of the rusty floor areas. One spot under the cowl needs attention as well. I have since plasma'd out a few spots and sprayed it all with ospho for rust treatment. Before the rockers can go on I'll have to repair the cab supports which means removing the clip. If the clip is off then might as well remove the motor / transmission and so forth.... ugh. Attached Images __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

03-29-2011, 10:39 AM	#32
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... More: Attached Images __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

03-29-2011, 10:41 AM	#33
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... Oh and I am not the hack that removed the rockers in such a sloppy manner. :/ __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

03-29-2011, 10:50 AM	#34
1LoC10 Insert Title Here Join Date: Feb 2006 Location: Dyer, Indiana Posts: 5,679	Re: Like I needed another one of these things.... cool truck __________________ BOBBY _69 SWB_ 1000 pics of 67-72's>> http://s193.photobucket.com/albums/z...-72/?start=all <<

07-25-2011, 10:53 AM	#35
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... My floorboard rust repairs are almost done - just need to pull the front clip, replace the pass lower pillar support and weld in the passenger rocker panel. I went ahead and laid down some rust cap paint, then seam sealer then topped it all with sound deadener. It runs from the cowl all the way to the line just below the upper gas tank mounts. Already a vast improvement over the rattles and engine noise. I have carpet, new door felts and floor vent seals to install next - Hopefully it'll be tight enough to keep the dirt dobbers out of there while it sits around waiting to be worked on. Attached Images __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

08-08-2011, 10:56 AM	#36
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... Floor repairs finished rockers on encapsulator painted top, bottom, cowl and inside doors seam sealed floors and cowl installed new felts and door rubber slapped on door panels / arm rests refurbished the floor vents I like how the doors close now. Here's a video of an open / shut: http://tinyurl.com/3s88hyk Attached Images __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

08-08-2011, 11:50 AM	#37
o6r1man Registered User Join Date: Aug 2008 Location: KS Posts: 268	Re: Like I needed another one of these things.... LOOKING GOOD!!!! I wish had a truck that nice to start with. __________________ 1970 SWB "old flame" 1967 SWB c10 sold 1972 Elcamino 496 2012 Denali HD dmax

08-08-2011, 01:22 PM	#38
33shooter Registered User Join Date: May 2010 Location: Austin Texas Posts: 84	Re: Like I needed another one of these things.... Looking good! I like the stance. Austin huh....I'll see you around I hope.

08-08-2011, 07:53 PM	#39
72Horn1Ton Registered User Join Date: Nov 2009 Location: Galveston, Texas Posts: 16	Re: Like I needed another one of these things.... I may have a fairly good front bumper.

08-08-2011, 09:01 PM	#40
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Like I needed another one of these things.... Nice progress!!! __________________ Looking for a 67-72 swb or blazer project in or around VA.



Register or Log In To remove these advertisements.

08-08-2011, 09:46 PM	#41
sean1969c10 Registered User Join Date: Mar 2008 Location: Powhatan, Va. Posts: 376	Re: Like I needed another one of these things.... Looking good!!!! __________________ Sean "If your gonna be dumb, you gotta be tough" 1960 Chevy Impala Sedan - my 25 year search is over!! 1969 C-10 longbed - Nice day DD 1970 Chevy Nova - Street and Strip Project 2002 Acura MDX my DD 2007 Honda Odssey - My Wife's "Mommy Van"

08-13-2011, 07:42 PM	#42
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... Made a a tad more progress today - •primed my drip rail (seam seal tomorrow) •added a transmission mount (PO had a chunk of 2" square tubing in there instead) •touched up other seam seal areas underneath •added my new to me GMC fender emblems •took some current pics I also found some rebuilt 062 vortec heads on craigslist that I'm thinking about buying myself for my birthday.... Then I can install the Edelbrock fuel injection, serpentine setup, 700-r4 and other goodies that I've got waiting for deployment. Too bad I can't do this 5 days a week and sit in a cube for 2. Attached Images __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

12-04-2011, 12:53 AM	#43
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... Update: Pulled the front and rear glass to touch up the seams and add CST trim. The dash is sanded and cleared to give the worn look that the outside has - maybe a tad too far but I can always cover it later.... Whatchu think? Glass install was less than smooth but it's at least done now. Thank goodness this is a patina truck and not a show truck or I'd be in jail for breaking the fingers of the install guys. Grr. Attached Images __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

12-04-2011, 12:54 AM	#44
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... Oh, and on a side note, the glass guys were EXTREMELY confused at the concept of having a truck all updated underneath with a rusty old faded exterior. (mission accomplished) __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

12-24-2011, 04:08 PM	#45
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... Picked up a Vortec donor truck this week. Merry Xmas to me! '98 Suburban 180k with a busted transmission - $1100 I'll vent some holiday aggression on the scrapping process. Attached Images __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

12-24-2011, 04:23 PM	#46
black_sheep454 Registered User Join Date: May 2011 Location: Lebanon, Mo. Posts: 1,315	Re: Like I needed another one of these things.... Trucks looking awesome, keep up the good work. Posted via Mobile Device __________________ 1968 chevy lwb, getting ready to join forces with the 70 gmc 1970 gmc swb, getting ready to be a 68 chevy swb 1971 gmc lwb 2500 2wd Sierra Grande 1988 chevy 1-ton crew cab 2wd waiting for a 12v cummins

12-24-2011, 04:48 PM	#47
mtm_seven Loading..... Join Date: Jan 2000 Location: Austin, Texas, USA Posts: 214	Re: Like I needed another one of these things.... Tow-tow Attached Images __________________ -M7 '69 SWB GMC 5.7 EFI ‘69 C/10 SWB patina survivor ‘71 GMC K20 '72 K5 1-ton gear 468BB ‘86 K30 GMC High Sierra C&C Single Cab '96 SWB Single Cab 5.7 ‘99 SWB Z71 Single Cab '00 SWB Single Cab 5.3 '01 K2500 Yukon Safari 6.0 ‘06 2500HD Single Cab C&C Duramax 4x4 '08 1500 crew '11 2500HD Single Cab Duramax 4x4

12-24-2011, 05:36 PM	#48
ChevLoRay Old Skool Club Join Date: Jun 2001 Location: Benton, AR "The Heart of Arkansas" Posts: 10,880	Re: Like I needed another one of these things.... The burb may have some resale potential on the 88-98 parts board..... __________________ Member Nr. 2770 '96 GMC Sportside; 4.3/SLT - Daily driven....constantly needs washed. '69 C-10 SWB; 350/TH400 - in limbo The older I get, the better I was.

12-24-2011, 06:38 PM	#49
lha1992 Registered User Join Date: Apr 2010 Location: Everett, WA Posts: 504	Re: Like I needed another one of these things.... Please note that you must be a supporting member to post classified items. This includes but is not limited to What Its Worth, Want To Buy, Want To Trade, and For Sale. Please consider supporting the forum by subscribing. Further information on the subscription levels available are located here If you need any further assistance with that please contact any Admin for help. Last edited by 70cst; 12-25-2011 at 01:02 PM.

12-24-2011, 11:39 PM	#50
chevy88 Registered User Join Date: May 2007 Location: Southern, Saskatchewan Posts: 640	Re: Like I needed another one of these things.... Those rims look really good, and hey I'd love to have a shop that we didnt have to heat all the time. __________________ Kerry My build thread. http://67-72chevytrucks.com/vboard/s....php?p=3657823 1971 Chev SWB with 68 nose, 6.2 diesel th350, and 3.73 rear gears 1988 Chev Extendacab 2010 Honda VT1300CS Sabre 2005 Buick Rendezvous wife's ride Last edited by chevy88; 12-24-2011 at 11:46 PM.

Register or Log In To remove these advertisements.