Camaro Caliper Brackets

[Captainfab]

PM replied to

[jdalexa84]

Do these use the rear or front rotors from the caprice/impala?

[jdalexa84]

Never mind I see that the front is not possible after looking them up

[68GMCCustom]

will these also work with c-clip eliminators?

[Captainfab]

It's been a long time since I've seen a set of c-clip eliminators. IIRC they bolt onto the axle flange on top of the backing plate? They would possibly work if you can get away with about 3/16" less axle spline engagement into your spiders. These brackets bolt on in place of the backing plates. Let me know.

Originally Posted by 68GMCCustom

will these also work with c-clip eliminators?

[darthwall]

just wanted to make sure they look like nice brackets I went a local yard today and found the front calipers and front brakes looking for the rears but my ? is aren't the camero's like a 4.75 or a4.50 lug

[Captainfab]

Yes the F-bodies are 5 x 4.75. That's why you use the Impala/Caprice rotors which are 5 x 5. The F-body calipers will work with the Impala/Caprice rotors.

[darthwall]

ok I see let me line up my parts and I will take a set of these also do you need to do a different dist block to level everything out

[Captainfab]

If you currently have a disc/drum proportioning valve, I would try it as first. Then if you need to reduce the rear braking bias, then install an adjustable valve in the rear line. Or if you prefer to not do that then you could install a disc/disc proportionining valve from the start. Let me know when you're ready.

BTW whereabouts in Washington are you?

[chopper john]

hey john , thanks for the fast great service. i didnt even think that you had the check yet. all the parts are a+++. i have a few questions. !should i run a disc/disc prop valve ? 2 does it matter what chamber on the master is for front and witch is for rear or does it matter. thanks

[Captainfab]

You can either run a disc/disc prop valve, or just plumb it direct from the MC and plumb in an adjustable prop valve in the rear line. Yes it does matter which line goes where. The ports have two different thread sizes.....I don't remember which one is which size. I'll check and get back to you.

Originally Posted by chopper john

hey john , thanks for the fast great service. i didnt even think that you had the check yet. all the parts are a+++. i have a few questions. !should i run a disc/disc prop valve ? 2 does it matter what chamber on the master is for front and witch is for rear or does it matter. thanks

[Captainfab]

Sorry I didn't get back sooner....been really busy.

Any way on the Corvette master it looks like the front port which is a 1/2-20 thread is for the front brakes and of course the rear port which is 9/19-18 thread is rear brakes. If you need anything else let me know.

[chopper john]

cool thanks john . im gonna try to install it all this week. and thanks a again for the fast service and beautiful parts

[Dizzy]

PM Sent! Just want to make sure these will work on a 68 with the conversion axles...

[Captainfab]

Yes they will work.

Your brackets are on their way......Thanks

Originally Posted by Dizzy

PM Sent! Just want to make sure these will work on a 68 with the conversion axles...

[Dizzy]

Originally Posted by Captainfab

Yes they will work.

Your brackets are on their way......Thanks

Got my brackets the other day... They look GREAT!!!! Can't wait to get the housing back and install everything. Thank you!

[Captainfab]

Thanks for the comments. Post up some pics when you get them installed.

Originally Posted by Dizzy

Got my brackets the other day... They look GREAT!!!! Can't wait to get the housing back and install everything. Thank you!

I got another small run of these brackets ordered from the laser cutter this morning.

[TheWraith]

sorry i spammed the impala bracket post - this is actually what i need. do you know of anyone who has tried this with 89-92 rear f-body brakes? i might try to pioneer it since i have a set of them sitting in my garage unused.

[Captainfab]

I used to make brackets that used the GM metric calipers (the '85-'92 rear calipers fall into that catagory) and the Lincoln rotors on the 10 and 12 bolt truck rear differentials. I have since sold out of those brackets, but I do plan on developing a new and improved design in the not to distant future. The original design can be seen HERE

Right now I'm working on a new rear disc conversion. The thread can be seen HERE

Originally Posted by TheWraith

sorry i spammed the impala bracket post - this is actually what i need. do you know of anyone who has tried this with 89-92 rear f-body brakes? i might try to pioneer it since i have a set of them sitting in my garage unused.

[TheWraith]

captainfab, the f-bodies used the iron calipers you referred to 84-88 only. 89-92 uses the aluminum pbr calipers, same as the 93-97, i just don't know if there's any variation on the mounting or anything.

i think i'll take my chances, and i'll let you know the outcome. do you still have sets of these 93-97 brackets available? i'll paypal today.

Thanks

[bigarmzz]

Captfab, i just bought a set of your impala SS brackets, got em a few days ago, they look fantastic!

just curious, can i use camaro calipers as well with those impala ss rotors? or do i need to use the impala calipers?

thanks alot

[Captainfab]

I'm afraid you'll have to use the Impala SS/Caprice calipers with those brackets since they mount a little differently.

Originally Posted by bigarmzz

Captfab, i just bought a set of your impala SS brackets, got em a few days ago, they look fantastic!

just curious, can i use camaro calipers as well with those impala ss rotors? or do i need to use the impala calipers?

thanks alot

[Captainfab]

I didn't realize that the '89-'92's were different from the '84-'88's......too many parts groups to keep straight

I did some searching and could only find pictures and no dimensions. In the pics I found they look very much the same so I don't know just what the difference is in them. The mounting holes in these brackets for the caliper bracket is 3.820" center to center.

I don't have a set of these brackets right now, but I will be ordering some on Monday, and I should have them by Tuesday. Let me know if that'll work for you.

Originally Posted by TheWraith

captainfab, the f-bodies used the iron calipers you referred to 84-88 only. 89-92 uses the aluminum pbr calipers, same as the 93-97, i just don't know if there's any variation on the mounting or anything.

i think i'll take my chances, and i'll let you know the outcome. do you still have sets of these 93-97 brackets available? i'll paypal today.

Thanks

[TheWraith]

i will definitely take a set of them. i have a set of the calipers, so i'll measure them out. i'll paypal in the next 24 hours.

[Captainfab]

Your PayPal payment has been received. I will get those parts ordered first thing in the morning. I'll let you know when they ship. It should be Tuesday if my supplier is still on their regular schedule.

Originally Posted by TheWraith

i will definitely take a set of them. i have a set of the calipers, so i'll measure them out. i'll paypal in the next 24 hours.