Stake pocket FILLER PANELS

[Snohog]

Glock, need a short bed set. Paypal sent. Thanks

[glock35ipsc]

Got it Snohog, thanks!!!

GUYS - Hold off on sending any more payments until I get back into the shop on Tuesday and count up what I have let. I am geting close to being out, and don't want to leave anyome hanging until I can get some more cut.

Thanks again to everyone who has ordered them!!!!!!!!

[glock35ipsc]

OK, for now, I have enough left here to make 3-4 sets for either long or short bed. Let me know what you need! I will have more available soon!

[IvelDesigns]

mine showed up the other day. Looks great.

thanks for a good product!

[glock35ipsc]

Thank you, glad you like them!!!

[409biscayne]

I need two sets , one long and one short . $$$ pls
Many thanks ........................... 409

[glock35ipsc]

409biscayne - $18.00 to your door. If you want to use Paypal, my addy is in the first post.

Thanks! Bob

[409biscayne]

Thank you ,i'll paypal tonite from home .
409

[Draggn66]

Bob....got them today! Thanks man.

[glock35ipsc]

Your welcome Randy, and thank you!

[project1971]

hey in you sig it says you have power frenched antenna kits what does that consist of and how much? i am assuming they are going where the filler neck was. VERY interested it that. Thanks!

[glock35ipsc]

The kit will consist of the tube with a drain nipple on the bottom, the power antenna unit, rubber/plastic tubing to run from the antenna tube to an exit point in the floor (to allow water that might collect in the tube to drain), and a reinforcement strip to support the antenna to keep it in place. All you will need to do is select a location, either where the fuel filler was, or on the other side of the cab), make the hole and fit it to the tube, and weld in place.

I am just getting to the point of de-burring and welding up the tubes, and I just got the first batch of antennas in. Should have them ready to go in a couple weeks max. I haven't set a firm price yet, but probably around $65-$75 complete. I will probably also sell the tube without the antenna is someone wants just that.

Just picture this:

[glock35ipsc]

I have 1 short bed set left for now, more to come soon.

[Snohog]

Glock, if you decide to make the door hinge shims Draggn66 asked about you have another buyer here. We could actually use several size shims similar to body shim sizes. I have used the body shims to close the gap in my doors, no more travel in hinges, but it does not look good and hard to get in place on some of the bolts.

[glock35ipsc]

It might be a possibility here in the very near future. I am in negotiations with my bank working on a small business loan to purchase a CNC plasma table and software, and to upgrade my plasma cutter. The new one is rated at a 1” genuine cut, 1-1⁄4” maximum cut, and 1-1⁄2” severance cut. I will be able to cut just about anything from something drawn on a napkin drawing to a photograph, and of course anything I can create on CAD.

If/when I can get that done, they sky will be the limit!!!

[Snohog]

I hope it works for you Glock, you get a cool piece of equipment and we get much needed parts.

[glock35ipsc]

409biscayne - You still interested?

[70rs/ss]

Glock, the rear brake pieces were beautiful, I need the door shim piece if you do them as my driver's door gap is big in the back and none in the front! I'd like a set of the pocket covers, but I am a snail mail kinda guy, if its OK PM me.

[glock35ipsc]

PM sent! Thanks!

[glock35ipsc]

OK ya'll, I have another 100 pieces cut and ready to be shipped! See the first post for prices.

Thanks!
Bob

[409biscayne]

Originally Posted by glock35ipsc

409biscayne - $18.00 to your door. If you want to use Paypal, my addy is in the first post.

Thanks! Bob

I'm sending you a Paypal right now , $18 for two sets , one longbox and one for short box . Woo hoo .
409

[glock35ipsc]

Got it! I need to pick up some more envelopes, then they will be on their way. Thanks!!

[project1971]

back on the antenna.... I am wanting mine where the fuel fill was, any way to make the opening in the shape of a bowtie?

[meathead95]

you should get with yukon jack and offer the reinforcement plates for the hydraulic clutch and hydroboost brake system that he is sending everyone a pattern of

[glock35ipsc]

Originally Posted by project1971

back on the antenna.... I am wanting mine where the fuel fill was, any way to make the opening in the shape of a bowtie?

Well, I guess it could be possible. The tube would need to be fabricated from thin flat bar to get the shape. It might look a little distorted when it gets set in place on the angle, but I could be wrong. I think thought that it would actually look pretty cool! I'll have to play with the idea in posterboard form to see what it might be like.