Aluminum 3 gage bezel

[mekdad]

Originally Posted by 2 Many Toys

Any time frame on that piece?

Not yet,I am hoping to get to it this week.I was asked about putting a radio hole in that same spot,But I got looking at it,and I don't think there is room,there is some ducting for the defrost vents that is in the way.

[VA72C10]

Originally Posted by mekdad

Not yet,I am hoping to get to it this week.I was asked about putting a radio hole in that same spot,But I got looking at it,and I don't think there is room,there is some ducting for the defrost vents that is in the way.

Any updates?

[VA72C10]

I'm going to take one of these and make it work and move the radio to the glovebox.

[2 Many Toys]

Originally Posted by 2 Many Toys

Any time frame on that piece?

Any update on this particular piece?

[mekdad]

I have made some.The one for 67 is done,but I am still working out the details on the 68-72.That one is proving to be a PIA with the big ignition and cig lighter bezels.Here are some preview pics and the one I am doing for NWD02 and his a/c controls.

[tommypic]

Originally Posted by mekdad

I have made some.The one for 67 is done,but I am still working out the details on the 68-72.That one is proving to be a PIA with the big ignition and cig lighter bezels.Here are some preview pics and the one I am doing for NWD02 and his a/c controls.

That 1 in the 1st pic that uses vintage air controls whats it fit ? 67 if so how much to 29673

[NWD02]

Tommy, that the one he's working on in the pictures is for my and yes it's the vintage air servo controls. I'm going with the GEN II kit.

[70c10]

Mekdad- 2 questions on the 68-72' style.
1. Can these be made with thinner metal?.
2. Can you make these with ball milled horizontal lines?

Thanks they look great!

[mekdad]

Originally Posted by 70c10

Mekdad- 2 questions on the 68-72' style.
1. Can these be made with thinner metal?.
2. Can you make these with ball milled horizontal lines?

Thanks they look great!

Still trying to get the mounting holes placed in a good spot for 68-72.There is just not any room in the top area with out modifying the heater control panel.I may end up only making them for the 67's,But I have not given up yet.


1. Can these be made with thinner metal?
If you don't mind screw holes all the way through the part

2. Can you make these with ball milled horizontal lines?
I can put all the lines in them you want or engrave what ever you want in any of the parts I make, for a little more cash.

[70c10]

I have a 4 piece kit that is thin like this pic. I am planning to use thin double sided tape to hold it on that's why I was asking about making it thin. Here's a pic I found to show the ball milled lines. In reality, you probably wouldn't see much line work because the heater face will take up most of it but it would probably look nice. My kit is aluminum that has been polished to a mirror.

[rustyg]

I'll take one of the four that you have if there are any left.
let me know.

[c10crazy]

Originally Posted by mekdad

I have made some.The one for 67 is done,but I am still working out the details on the 68-72.That one is proving to be a PIA with the big ignition and cig lighter bezels.Here are some preview pics and the one I am doing for NWD02 and his a/c controls.

Did you ever finalize the 68-72 style heater control plate?. How much are those going to be?

[mekdad]

Still have three of these.

c10crazy,It does not look like I can make a 68-72 that would not require modification to the dash or components,other than small holes.

[Deenice21]

Originally Posted by mekdad

$35.00 shipped to your door. These fit in the radio hole in a cut up dash.Yes you can cut your dash just to put these in .They also come with mounting hard ware (8-32 screws and washers),and mount from the back so you cant see them.They fit 2 inch gages, The holes are 2.065

ur pms are full

[oldblue1968chevy]

i like that!!