1947 Chevy Truck Hotrod - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

av8tr33337 · 10-27-2013, 11:07 AM

Awesome video. You have got way more knowledge than I do on the engine stuff. It won't be long now and you will be driving it around!

Angryman117 · 10-30-2013, 01:08 AM

Root,
Yes I did the mods myself, however I just did some simple stuff like turn off vats, egr, rear o2 sensors, and a few other things. I use EFI Live, it cost me $800 a few years ago.

Bartman,
Thanks. Should have some more pictures in a few days, had to modify my exhaust system again for the fuel tank. But I think it looks better now.

Angryman117 · 11-04-2013, 12:34 AM

Got the fuel tank installed. The tank if out of an 89 Blazer with TBI and holds 31 gallons. Had to reconfigure my exhaust again, but I think it looks better now also put a set of flow-masters in that I had sitting on the shelf in the garage. Here are some pictures of the install.

Angryman117 · 11-10-2013, 10:45 PM

Made some more progress. Got the steering installed, took some measurements from a truck just like the donor and got every thing pretty close but will find out how I did once I am able to drive it. Here are some more pictures.

Stock 5.3 oil pan looks like it belongs there from the factory.

My intake not sure if I will leave it like that, but for now it works.

Radiator fan, it looks small but is actually good size and it will move some air quite nicely! I wanted a bigger one but have very little room to work with.

Finally getting started on the cab. It has the typical rusty spots. The previous owner attempted to repair the rear drivers corner poorly, and made a custom dash for it and hacked the old one to hell, so i will make my own custom one that looks nice. I plan on using this Dakota Digital Universal setup.

The steering wheel and column I am going to use.

Root2812 · 11-11-2013, 01:05 AM

I like what you have done with the motor and suspension. Its coming along nicely.

That cab is in really bad shape. With the amount of time and cost of replacement sheet metal you might be better off finding another cab to start with.

Angryman117 · 11-11-2013, 11:12 PM

The cab is actually better than it looks in the pictures. I do have another cab on my parts truck and look about the same as this one, maybe even a little worse. I already have the hole the PO hacked out for the heater patched, and the hacked up dash pulled out so I can start working on my custom one. My plan is to just use some of the spare pieces of sheet metal that I have to patch the small stuff and buy a big piece for floor and front sides. I will need to get one patch panel for rear left, the right side is good.

Angryman117 · 11-12-2013, 01:30 PM

Here is a picture of what the dash looked like when I got the truck. My plan is to keep the same basic look.

Angryman117 · 11-28-2013, 10:54 AM

Slowly making progress on the cab. It's not perfect and have lots of finish work to do, but hopefully I can have the cab back on the frame sometime this weekend. For my first time doing this type of work I think it's turning out pretty good, but could be better.

Angryman117 · 11-28-2013, 03:53 PM

Needed a break from working on the cab so I installed the drive shaft.

av8tr33337 · 11-29-2013, 12:00 AM

Looking good. My floor patch job will be very similar to yours. Can you tell me where you got the metal and the thickens??

Angryman117 · 11-30-2013, 02:23 AM

Quote:

Originally Posted by av8tr33337

Looking good. My floor patch job will be very similar to yours. Can you tell me where you got the metal and the thickens??

I am using 16ga sheet metal. I got it free from my uncle and have no idea where he got it. I'm heading to the local metal place out here tomorrow to see if I can get a few more pieces so I can finish the floor.

Angryman117 · 11-30-2013, 02:31 AM

Setting the cab back on the frame with my cherry picker.

Installing the rear cab support bar.

Engine to firewall clearance.

I have plenty of room between the floor and transmission so I don't have to make a tranny hump.

My seats, driver side still needs cleaning but ran out of cleaner, plus have to repair the spring under the cushion.

mud.man.rj · 11-30-2013, 02:50 AM

Very interesting build, nice exh work and routing. Watching for updates.

msaintg · 11-30-2013, 08:32 AM

two questions..... your drive shaft appears to be 2" too short. Is that just the pics? Are you concerned about how much your gas tank is going to hang down below the bumper?

Angryman117 · 11-30-2013, 11:59 AM

Quote:

Originally Posted by msaintg

two questions..... your drive shaft appears to be 2" too short. Is that just the pics? Are you concerned about how much your gas tank is going to hang down below the bumper?

The drive shaft is only 1/2 inch short but hard to tell from the picture. I got it cut that way because the box and cab are not on the frame for the extra weight.
For the gas tank that picture makes it look lower than it is, but I have the skid plate for that tank that I will also be installing for extra protection.

alaska gasser · 11-30-2013, 12:20 PM

Quote:

Originally Posted by Angryman117

For the gas tank that picture makes it look lower than it is, but I have the skid plate for that tank that I will also be installing for extra protection.

Have you thought about raising the tank? It looks like it could move up a couple of inches. Just curious as it would be protected more and look asthetically better once it is all together.

47 Fasttoys · 11-30-2013, 07:11 PM

Just for reference, I have a 33 gallon tank on my '46 which mounts in the same location. It does hang a little low but has never been a issue. Mine is a no where near a show truck so looks are not a major issue, I can however go over 400 miles on a tank.
Rob

Angryman117 · 11-30-2013, 10:29 PM

Quote:

Originally Posted by alaska gasser

Have you thought about raising the tank? It looks like it could move up a couple of inches. Just curious as it would be protected more and look asthetically better once it is all together.

I might raise the tank once I get closer to finishing the truck and make all the final small adjustments. I measured the distance today and I can raise it up 3 inches.

Angryman117 · 11-30-2013, 10:37 PM

Got the back part of the floor tacked in.

Also test fitting the seats. It going to be tight and I have to squeeze the middle seat in, but looks like they will fit (barley).

**oldman3** · 12-01-2013, 12:22 AM

Very interesting build, I'm along for the ride...Jim

T Hilde · 12-01-2013, 03:07 AM

I used the same seats. Honestly, the center needs to be narrowed by half.

Angryman117 · 12-04-2013, 05:48 PM

Quote:

Originally Posted by T Hilde

I used the same seats. Honestly, the center needs to be narrowed by half.

Looks like I will have to narrow the middle seat about 4 inches and then squish the rest in. But thanks for the heads up.

Angryman117 · 12-04-2013, 05:52 PM

Finally got a tire changing machine, and mounted up one of my wheels that I am using for my build.

69CST-V · 12-04-2013, 06:00 PM

Nice start. sub'd

hotrodrookie · 12-04-2013, 11:38 PM

Nice project. +1 on the LS swap. I can't wait to fire mine for the first time.

10-27-2013, 11:07 AM	#26
av8tr33337 Registered User Join Date: Mar 2009 Location: Derby Kansas Posts: 564	Re: 1947 Chevy Truck Hotrod Awesome video. You have got way more knowledge than I do on the engine stuff. It won't be long now and you will be driving it around! __________________ av8tr33337 AKA Bartman Email av8tr33337@yahoo.com Bartman's Ad-S10 Chassis Swap http://67-72chevytrucks.com/vboard/s...d.php?t=415418 My First Youtube Video http://www.youtube.com/watch?v=B6hSt...eature=channel More Pics of the 51 Project http://s668.photobucket.com/albums/v...hassis%20Swap/ 1951 3100 Pickup

10-30-2013, 01:08 AM	#27
Angryman117 Registered User Join Date: Jul 2013 Location: VAFB, CA Posts: 227	Re: 1947 Chevy Truck Hotrod Root, Yes I did the mods myself, however I just did some simple stuff like turn off vats, egr, rear o2 sensors, and a few other things. I use EFI Live, it cost me $800 a few years ago. Bartman, Thanks. Should have some more pictures in a few days, had to modify my exhaust system again for the fuel tank. But I think it looks better now. __________________ Angryman117's 47 Chevy Build 89 Silverado Z71 LS Swap (sold)

11-04-2013, 12:34 AM	#28
Angryman117 Registered User Join Date: Jul 2013 Location: VAFB, CA Posts: 227	Re: 1947 Chevy Truck Hotrod Got the fuel tank installed. The tank if out of an 89 Blazer with TBI and holds 31 gallons. Had to reconfigure my exhaust again, but I think it looks better now also put a set of flow-masters in that I had sitting on the shelf in the garage. Here are some pictures of the install. __________________ Angryman117's 47 Chevy Build 89 Silverado Z71 LS Swap (sold)

11-10-2013, 10:45 PM	#29
Angryman117 Registered User Join Date: Jul 2013 Location: VAFB, CA Posts: 227	Re: 1947 Chevy Truck Hotrod Made some more progress. Got the steering installed, took some measurements from a truck just like the donor and got every thing pretty close but will find out how I did once I am able to drive it. Here are some more pictures. Stock 5.3 oil pan looks like it belongs there from the factory. My intake not sure if I will leave it like that, but for now it works. Radiator fan, it looks small but is actually good size and it will move some air quite nicely! I wanted a bigger one but have very little room to work with. Finally getting started on the cab. It has the typical rusty spots. The previous owner attempted to repair the rear drivers corner poorly, and made a custom dash for it and hacked the old one to hell, so i will make my own custom one that looks nice. I plan on using this Dakota Digital Universal setup. The steering wheel and column I am going to use. __________________ Angryman117's 47 Chevy Build 89 Silverado Z71 LS Swap (sold)

11-11-2013, 01:05 AM	#30
Root2812 Registered User Join Date: Aug 2011 Location: Barnum, Mn Posts: 795	Re: 1947 Chevy Truck Hotrod I like what you have done with the motor and suspension. Its coming along nicely. That cab is in really bad shape. With the amount of time and cost of replacement sheet metal you might be better off finding another cab to start with. __________________ My 1950 Chevy build

11-11-2013, 11:12 PM	#31
Angryman117 Registered User Join Date: Jul 2013 Location: VAFB, CA Posts: 227	Re: 1947 Chevy Truck Hotrod The cab is actually better than it looks in the pictures. I do have another cab on my parts truck and look about the same as this one, maybe even a little worse. I already have the hole the PO hacked out for the heater patched, and the hacked up dash pulled out so I can start working on my custom one. My plan is to just use some of the spare pieces of sheet metal that I have to patch the small stuff and buy a big piece for floor and front sides. I will need to get one patch panel for rear left, the right side is good. __________________ Angryman117's 47 Chevy Build 89 Silverado Z71 LS Swap (sold)

11-12-2013, 01:30 PM	#32
Angryman117 Registered User Join Date: Jul 2013 Location: VAFB, CA Posts: 227	Re: 1947 Chevy Truck Hotrod Here is a picture of what the dash looked like when I got the truck. My plan is to keep the same basic look. __________________ Angryman117's 47 Chevy Build 89 Silverado Z71 LS Swap (sold)

11-28-2013, 10:54 AM	#33
Angryman117 Registered User Join Date: Jul 2013 Location: VAFB, CA Posts: 227	Re: 1947 Chevy Truck Hotrod Slowly making progress on the cab. It's not perfect and have lots of finish work to do, but hopefully I can have the cab back on the frame sometime this weekend. For my first time doing this type of work I think it's turning out pretty good, but could be better. __________________ Angryman117's 47 Chevy Build 89 Silverado Z71 LS Swap (sold)

11-28-2013, 03:53 PM	#34
Angryman117 Registered User Join Date: Jul 2013 Location: VAFB, CA Posts: 227	Re: 1947 Chevy Truck Hotrod Needed a break from working on the cab so I installed the drive shaft. __________________ Angryman117's 47 Chevy Build 89 Silverado Z71 LS Swap (sold)

11-29-2013, 12:00 AM	#35
av8tr33337 Registered User Join Date: Mar 2009 Location: Derby Kansas Posts: 564	Re: 1947 Chevy Truck Hotrod Looking good. My floor patch job will be very similar to yours. Can you tell me where you got the metal and the thickens?? __________________ av8tr33337 AKA Bartman Email av8tr33337@yahoo.com Bartman's Ad-S10 Chassis Swap http://67-72chevytrucks.com/vboard/s...d.php?t=415418 My First Youtube Video http://www.youtube.com/watch?v=B6hSt...eature=channel More Pics of the 51 Project http://s668.photobucket.com/albums/v...hassis%20Swap/ 1951 3100 Pickup

11-30-2013, 02:31 AM	#37
Angryman117 Registered User Join Date: Jul 2013 Location: VAFB, CA Posts: 227	Re: 1947 Chevy Truck Hotrod Setting the cab back on the frame with my cherry picker. Installing the rear cab support bar. Engine to firewall clearance. I have plenty of room between the floor and transmission so I don't have to make a tranny hump. My seats, driver side still needs cleaning but ran out of cleaner, plus have to repair the spring under the cushion. __________________ Angryman117's 47 Chevy Build 89 Silverado Z71 LS Swap (sold)

11-30-2013, 02:50 AM	#38
mud.man.rj Registered User Join Date: Dec 2011 Location: Creighton Sask. Canada Posts: 4,121	Re: 1947 Chevy Truck Hotrod Very interesting build, nice exh work and routing. Watching for updates. __________________ 1987 Green n Green machine. 5.0 4spd std. 7" lift w 35's.

11-30-2013, 08:32 AM	#39
msaintg Registered User Join Date: Apr 2012 Location: Gilbert, Arizona Posts: 454	Re: 1947 Chevy Truck Hotrod two questions..... your drive shaft appears to be 2" too short. Is that just the pics? Are you concerned about how much your gas tank is going to hang down below the bumper? __________________ Mike http://67-72chevytrucks.com/vboard/s...d.php?t=526387

11-30-2013, 07:11 PM	#42
47 Fasttoys Registered User Join Date: Sep 2013 Location: Westminster, SC Posts: 933	Re: 1947 Chevy Truck Hotrod Just for reference, I have a 33 gallon tank on my '46 which mounts in the same location. It does hang a little low but has never been a issue. Mine is a no where near a show truck so looks are not a major issue, I can however go over 400 miles on a tank. Rob __________________ My '47 C.O.E build

11-30-2013, 10:37 PM	#44
Angryman117 Registered User Join Date: Jul 2013 Location: VAFB, CA Posts: 227	Re: 1947 Chevy Truck Hotrod Got the back part of the floor tacked in. Also test fitting the seats. It going to be tight and I have to squeeze the middle seat in, but looks like they will fit (barley). __________________ Angryman117's 47 Chevy Build 89 Silverado Z71 LS Swap (sold)



Register or Log In To remove these advertisements.

12-01-2013, 12:22 AM	#45
oldman3 Senior Member Join Date: Mar 2011 Location: West Plains, Missouri Posts: 7,559	Re: 1947 Chevy Truck Hotrod Very interesting build, I'm along for the ride...Jim __________________ my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br />

12-01-2013, 03:07 AM	#46
T Hilde Registered User Join Date: Apr 2009 Location: Faribault, MN Posts: 385	Re: 1947 Chevy Truck Hotrod I used the same seats. Honestly, the center needs to be narrowed by half. __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=414646

12-04-2013, 05:52 PM	#48
Angryman117 Registered User Join Date: Jul 2013 Location: VAFB, CA Posts: 227	Re: 1947 Chevy Truck Hotrod Finally got a tire changing machine, and mounted up one of my wheels that I am using for my build. __________________ Angryman117's 47 Chevy Build 89 Silverado Z71 LS Swap (sold)

12-04-2013, 06:00 PM	#49
69CST-V Registered User Join Date: Mar 2010 Location: Piper, KS Posts: 683	Re: 1947 Chevy Truck Hotrod Nice start. sub'd __________________ Bryce '69 SWB Fleet Still Under Construction Company Trucks

12-04-2013, 11:38 PM	#50
hotrodrookie Registered User Join Date: Sep 2008 Location: Sacramento Posts: 425	Re: 1947 Chevy Truck Hotrod Nice project. +1 on the LS swap. I can't wait to fire mine for the first time.

Register or Log In To remove these advertisements.