WA Cab cuts, most cuts $45ea plus shipping

[randy500]

Originally Posted by rayce88

Drip rails and roof ? .... Shipping to 36575

I have a single drivers drip rail, sell for $35 plus shipping estimated st $25or so,
I have some nice outer roofs, last one I shipped in a crate I made, through busfreighter, I think shipping was $145 or so. I would need $100 for the roof and packaging.

[randy500]

I have a passenger drip rail it’s cut about 2 inches past the cab seam.

[randy500]

Originally Posted by kiwikid

right and left drip rails ?

Pics of your rails removed.

[randy500]

The inner side of drip rails

[randy500]

Originally Posted by Tdrcreyn4

Randy,

All of that sounds fine including cutting in half. I want to preserve the back of the cab as well and the rust on my cab corners went about 6 inches higher than replacement cab corners. Please PM me with total and your payment info. Thanks

Todd

How far above the body line do you want it cut? I will cut it off and get a shipping quote for you.

[randy500]

Sorry if I haven't replied to anyone...did I miss anyone's requests?
I have another 68 cab I am cutting up so let me know what you may need.

[randy500]

Originally Posted by wahl4m

how about the area around the gas pedal -where your heel rests! & there is pivot pin studs there ?? thanks mike

I got your PM and tried to reply, your PM box is full.
Sorry I forgot about you...
I checked and that area is good and has 2 gas pedal ball studs that appear to be usable.
$45 for the cut, I need dimentions from the pin centerline, up down left and right for the cut.
I estimate shipping at $22.

[Tdrcreyn4]

Randy,

Need 7 inches above the body line on the cab corners please.

Thanks,

Todd

[randy500]

Originally Posted by Tdrcreyn4

Randy,

Need 7 inches above the body line on the cab corners please.

Thanks,

Todd

Pics of the cab, driver corner has a dent but no rust noted, inside is rhino lined

[randy500]

The dent

[randy500]

The inside

[Tdrcreyn4]

Looks fine thanks.

Todd

[randy500]

Originally Posted by Tdrcreyn4

Looks fine thanks.

Todd

Ok, I will cut that today and get a shipping quote.

[Jcfcamaro]

What about the seat belt cage nut plates? Are you selling them and how much

[RodnRudy]

Received the sheet metal pieces I ordered from you today. I'm a happy camper and it was a pleasure doing business with you Randy.

[randy500]

Originally Posted by Jcfcamaro

What about the seat belt cage nut plates? Are you selling them and how much

I can get those for you, which ones do you need? Inners? Outers? All 4?

[randy500]

Originally Posted by RodnRudy

Received the sheet metal pieces I ordered from you today. I'm a happy camper and it was a pleasure doing business with you Randy.

It was a pleasure doing business with you too.

[Jcfcamaro]

Just the 2 under the fuel tank. They are a flat plate with the cage and nut inside.

[randy500]

Originally Posted by Jcfcamaro

Just the 2 under the fuel tank. They are a flat plate with the cage and nut inside.

I have taken those out before...
$45 shipped, I can take them out today. There is a link to my paypal in my signature line, please put a note in there of what your paying for.

[Jcfcamaro]

I'm going to pass, just looked at mine and there not as bad as I thought

[randy500]

Originally Posted by Jcfcamaro

I'm going to pass, just looked at mine and there not as bad as I thought

Ok, if you need any other cuts let me know, 2 cabs getting cut up here....

[Tmac85]

Need entire floor if it’s in good condition shipped to 23314, lmk thanks.
Posted via Mobile Device

[randy500]

Ttt

[Tdrcreyn4]

Originally Posted by randy500

Ok, I will cut that today and get a shipping quote.

Have you had a chance to cut and get a shipping quote yet?
Thanks.

[novice]

I'm in need of the lower windshield area for the drivers side.