What did you do to your truck today! - Page 20 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

07SSSC · 07-13-2010, 11:37 PM

Nothin on the '69, but got the core support pulled off the wrecked '86 burb I picked up a few months back. Part of the accessory drive will probably end up on my '69 so that counts towards this thread, the engine will go into my '84 Trans Am.

bigt76_98 · 07-13-2010, 11:54 PM

got the '70 out today runnin a little hot in this kansas heat and i think the bearings are goin out in the water pump

mgkgmc · 07-14-2010, 01:40 AM

Took my bench seat out today to get redone. New springs,foam and material...cant wait to see it finished.

Tomahawk30 · 07-14-2010, 02:07 AM

Installed the new woodgrain dash bezel!

**Shock_Me** · 07-14-2010, 06:03 AM

Installed a new fuel pump on the Blazer. Pretty simple job

danielwetpaint · 07-14-2010, 06:59 AM

On my 1974 GMC,, I swapped the 3:73 12 bolt rear end for a 3:31 geared 12 bolt rear end,,plus completely re-did the brakes.
Man what a difference! My little 250 6 cylinder went from buzzin' 3 grand down to a little over 2.

Lippyp · 07-14-2010, 12:43 PM

As the weather has been too rubbish to finish up the engine wiring I've been ripping off the tints from the windows between rain showers, the side windows were almost limo black, a real PITA to drive after dark and also illegally dark now here so they have to go before I get tugged by Plod and made to rip them off at the roadside. The rear window had only had the two sliding bits tinted and obviously at a different time to the sides as it was much thinner and had gone purple with age and the side windows were not well done and actually had a patch on them. The film came off easily, the glue has used up half a can of cellulose paint thinners so far to remove but it is coming off nicely.

Looked cool when parked up but not worth the hassle.

67Slider · 07-14-2010, 10:54 PM

Finished wiring the engine back in. Bench bled the new MC and repainted my booster cause the old MC bled all over it.
[IMG]

[/IMG]

Did this a few days ago but it turned out good......

[IMG]

[/IMG]

Hubscrub · 07-14-2010, 10:57 PM

cleaned up and painted battery tray for the 67

07SSSC · 07-15-2010, 12:26 AM

Removed the alt and ps pump along with all the associated bracketry and the water pump pulley of the '69. Removed the alt, ps pump, A.I.R. pump, a/c compressor, water pump pulley and crank pulley off the burb. Gonna start mock up tomorrow, gotta figure out a cool/clean way to alter the ps brackets to work though.

Hubscrub · 07-17-2010, 07:22 PM

painted my bumper, installed headlight shields and finally painted me a shop logo

Thealien · 07-17-2010, 08:08 PM

fixed the cruise control/drove it

vectorit · 07-17-2010, 08:49 PM

Removed my broken hood latch, then went inside and stared at her from inside.

It's 107 degrees outside right now

treeboy97 · 07-17-2010, 09:07 PM

installed new disk brakes and lowered the front 2 inches and the back 4 inches.

Rob H. · 07-17-2010, 09:24 PM

Today nothing, yesterday I moved the 67 so I could mow where it was sitting and put the rear end down hill so the water would drain from the bed. Unfortuneatly it only moves in reverse. The 72 is still sitting in the same spot with the front wheels off and up on blocks, don't have to worry about it's bed holding water, it's rusty enough to be self draining!

Shyguy · 07-17-2010, 09:28 PM

Today, I started the '67 swb stepper and moved it out of the garage so I could work on the ole Jubilee tractor.

I looked at the '71 and said darn one of these days will be your turn.

OhioDan · 07-17-2010, 09:54 PM

Finished the interior. Grandson got me a decal for my birthday, so I had to put it on.

**yote1234** · 07-17-2010, 10:21 PM

got the cab on frame...

67Slider · 07-17-2010, 10:38 PM

The boy and I put the fan shroud and fan back in,
[IMG]

[/IMG]

replaced the old MC (no leaks this time),
[IMG]

[/IMG]
started putting in the B&M mega shifter, Put the driver door back together,
[IMG]

[/IMG]
DAMN HOT!!!! 103 today in Colorado so I would work a bit and cool off, repeat, repeat and repeat!

Yote1234 - I dig that paint job!!!! Very nice!

bddcustoms · 07-17-2010, 10:53 PM

drilled some spot welds out on the cab -- only had a few minutes to play today.

oldblue1968chevy · 07-17-2010, 11:05 PM

wire wheeled greasy bolts/brackets off gettin' ready for painting sometime soon!

**FRENCHBLUE72** · 07-17-2010, 11:08 PM

I swept around the 72 and am doing brakes right now on the blazer..

**yote1234** · 07-17-2010, 11:08 PM

67slider... your looks great also. so you only hit 103? we hit 116 and at 8.00 pm were still over 100 deg. thats hot... again...nice paint..

willys72fleetside · 07-17-2010, 11:18 PM

Didn't have much time but was able to get the seat adjuster wire run from side to side. Every little bit helps!

marks1972 · 07-17-2010, 11:27 PM

Took mine to a local Cruz in. Just hapened to drive by it. I didn't even know we had them down here. Come to find out we do every Sat night.

07-13-2010, 11:37 PM	#476
07SSSC Registered User Join Date: Apr 2009 Location: Buhl, ID Posts: 288	Re: What did you do to your truck today! Nothin on the '69, but got the core support pulled off the wrecked '86 burb I picked up a few months back. Part of the accessory drive will probably end up on my '69 so that counts towards this thread, the engine will go into my '84 Trans Am. __________________ '69 Chevy C/10-under reconstruction -- '68 C20 Camper 50th Anniversary-runs, but sorely needs a resto -- '07 Cobalt SS/SC-very fun DD -- '93 Chevy K2500-LQ4/4L80E swap -- '84 Trans Am-awaiting (LS) drivetrain -- '00 Trans Am-road tripper -- '06 Z06-577 WHP beast

07-13-2010, 11:54 PM	#477
bigt76_98 Registered User Join Date: Mar 2009 Location: Kansas Posts: 16	Re: What did you do to your truck today! got the '70 out today runnin a little hot in this kansas heat and i think the bearings are goin out in the water pump

07-14-2010, 01:40 AM	#478
mgkgmc Registered User Join Date: Dec 2007 Location: Glendale Arizona Posts: 1,354	Re: What did you do to your truck today! Took my bench seat out today to get redone. New springs,foam and material...cant wait to see it finished.

07-14-2010, 02:07 AM	#479
Tomahawk30 Registered User Join Date: Jun 2010 Location: Russellville, KY Posts: 956	Re: What did you do to your truck today! Installed the new woodgrain dash bezel! __________________ 1979 Silverado C10 Shortbox - Photo Album 1977 Silverado K20 Camper Special - Photo Album 1972 C10 Custom Deluxe Highlander - sold 1971 Cheyenne Super Longhorn -sold 1972 Cheyenne Super SWB 4x4 -sold, bought back, sold again... I'm dumb. 1970 Chevy C10 SWB "Sprout" -sold 1972 Cheyenne K20 -sold 1969 GMC Shortbox Stepside 4x4 -sold 1972 GMC Jimmy 4x4 -sold

07-14-2010, 06:03 AM	#480
Shock_Me Senior Member Join Date: May 2005 Location: New Brunswick, Canada Posts: 587	Re: What did you do to your truck today! Installed a new fuel pump on the Blazer. Pretty simple job

07-14-2010, 06:59 AM	#481
danielwetpaint Registered User Join Date: Feb 2008 Location: Wye Mtn Ark Posts: 58	Re: What did you do to your truck today! On my 1974 GMC,, I swapped the 3:73 12 bolt rear end for a 3:31 geared 12 bolt rear end,,plus completely re-did the brakes. Man what a difference! My little 250 6 cylinder went from buzzin' 3 grand down to a little over 2. __________________ Current ridesne owner GMC 1974 swb, 1986 Chevy lwb,chopped top '85 S-10,1948 Stylemaster rat rod,'2008 Honda Civ.Chopped top '46 dodge.

07-14-2010, 12:43 PM	#482
Lippyp English Chevy Owner Join Date: May 2002 Location: Shropshire, UK/ Lot, France Posts: 1,848	Re: What did you do to your truck today! As the weather has been too rubbish to finish up the engine wiring I've been ripping off the tints from the windows between rain showers, the side windows were almost limo black, a real PITA to drive after dark and also illegally dark now here so they have to go before I get tugged by Plod and made to rip them off at the roadside. The rear window had only had the two sliding bits tinted and obviously at a different time to the sides as it was much thinner and had gone purple with age and the side windows were not well done and actually had a patch on them. The film came off easily, the glue has used up half a can of cellulose paint thinners so far to remove but it is coming off nicely. Looked cool when parked up but not worth the hassle. __________________ Phil '67 C10 long fleet. 350/TH350, 4 bbl Carter, K&N, Dual exhaust, loads of stuff coming soon 2001 S10 Blazer Daily Driver, bone stock 4 door 4x4 with manual transmission Last edited by Lippyp; 07-14-2010 at 12:46 PM.

07-14-2010, 10:54 PM	#483
67Slider Registered User Join Date: Mar 2010 Location: Pueblo West, CO Posts: 944	Re: What did you do to your truck today! Finished wiring the engine back in. Bench bled the new MC and repainted my booster cause the old MC bled all over it. [IMG][/IMG] Did this a few days ago but it turned out good...... [IMG][/IMG] __________________ 67 C10 Stepside 66 Mustang Coupe 99 Burb 2500

07-14-2010, 10:57 PM	#484
Hubscrub Cruzin Join Date: Dec 2009 Location: on the road Posts: 2,835	Re: What did you do to your truck today! cleaned up and painted battery tray for the 67 __________________ Lime Wife's 67https://www.google.com/url?sa=t&rct=...wZEMODaS2d94u8 Back to the Fifties 59 https://www.google.com/url?sa=t&rct=...NAeStpydfrcj_U Proverbs 3:5,6 "Thanks to the Interstate Highway System, it is now possible to travel across the country from coast to coast without seeing anything."Charles Kuralt In memory of our first baby daughter, daddy and mommy love you. Danica Grace 6/26/14

07-15-2010, 12:26 AM	#485
07SSSC Registered User Join Date: Apr 2009 Location: Buhl, ID Posts: 288	Re: What did you do to your truck today! Removed the alt and ps pump along with all the associated bracketry and the water pump pulley of the '69. Removed the alt, ps pump, A.I.R. pump, a/c compressor, water pump pulley and crank pulley off the burb. Gonna start mock up tomorrow, gotta figure out a cool/clean way to alter the ps brackets to work though. __________________ '69 Chevy C/10-under reconstruction -- '68 C20 Camper 50th Anniversary-runs, but sorely needs a resto -- '07 Cobalt SS/SC-very fun DD -- '93 Chevy K2500-LQ4/4L80E swap -- '84 Trans Am-awaiting (LS) drivetrain -- '00 Trans Am-road tripper -- '06 Z06-577 WHP beast

07-17-2010, 07:22 PM	#486
Hubscrub Cruzin Join Date: Dec 2009 Location: on the road Posts: 2,835	Re: What did you do to your truck today! painted my bumper, installed headlight shields and finally painted me a shop logo Attached Images __________________ Lime Wife's 67https://www.google.com/url?sa=t&rct=...wZEMODaS2d94u8 Back to the Fifties 59 https://www.google.com/url?sa=t&rct=...NAeStpydfrcj_U Proverbs 3:5,6 "Thanks to the Interstate Highway System, it is now possible to travel across the country from coast to coast without seeing anything."Charles Kuralt In memory of our first baby daughter, daddy and mommy love you. Danica Grace 6/26/14

07-17-2010, 08:08 PM	#487
Thealien Senior Member Join Date: Jun 2007 Location: Pine Ridge Florida Posts: 4,125	Re: What did you do to your truck today! fixed the cruise control/drove it __________________ Click on my Not really a build thread, yet NOT SO RUST FREE RUST FREE BLAZER LS ENGINE SWAP INFORMATION THREAD BOLT RESTORATIONS 4l60 to an NP205

07-17-2010, 08:49 PM	#488
vectorit What? Join Date: Jun 2007 Location: Southern California Posts: 7,617	Re: What did you do to your truck today! Removed my broken hood latch, then went inside and stared at her from inside. It's 107 degrees outside right now __________________ Chris 1968 K20 Suburban 1972 K10 LWB PU

07-17-2010, 09:07 PM	#489
treeboy97 Registered User Join Date: May 2009 Location: Waynesville, Ohio Posts: 136	Re: What did you do to your truck today! installed new disk brakes and lowered the front 2 inches and the back 4 inches. __________________ 1970 C10 LWB (Grandfather's Truck) 5.3 4L60E 2012 Victory Cross Country Touring I'm not wasting money on my truck/bike, I'm helping to rescue the economy one mod at a time.

07-17-2010, 09:24 PM	#490
Rob H. Registered User Join Date: Nov 2008 Location: Petersville KY Posts: 673	Re: What did you do to your truck today! Today nothing, yesterday I moved the 67 so I could mow where it was sitting and put the rear end down hill so the water would drain from the bed. Unfortuneatly it only moves in reverse. The 72 is still sitting in the same spot with the front wheels off and up on blocks, don't have to worry about it's bed holding water, it's rusty enough to be self draining! __________________ Rob 72 C/10 (under reconstruction)(destruction ? LOL) 48 Willys CJ2A 1952 Super "A" Farmall (Grandfather's)



Register or Log In To remove these advertisements.

07-17-2010, 09:28 PM	#491
Shyguy Junior Member Join Date: Dec 2006 Location: Southeast Missouri Posts: 2,436	Re: What did you do to your truck today! Today, I started the '67 swb stepper and moved it out of the garage so I could work on the ole Jubilee tractor. I looked at the '71 and said darn one of these days will be your turn. __________________ '67 Chevy C-20 short stepper - build complete, 454/SM-465. '75 C-30 Single Cab DRW-350 small block/NP-435. '77 GMC-6500 Dump Truck, 427 Tall Deck. '92 GMC K-3500 Duallie, 454/4L80E.

07-17-2010, 09:54 PM	#492
OhioDan Registered User Join Date: Apr 2002 Location: New Carlisle, Ohio,USA Posts: 1,404	Re: What did you do to your truck today! Finished the interior. Grandson got me a decal for my birthday, so I had to put it on. Attached Images __________________ LIFE AIN'T EASY WHEN YER FAT AND GREASY! GMC= Got More Class! 1970 GMC LWB, Fleetside, 350/4spd, Flowmaster "40's", 2002 GMC 16" Rallies, cowl hood,and added a bunch of options that weren't there when I started.

07-17-2010, 10:21 PM	#493
yote1234 Senior Member Join Date: Feb 2003 Location: Gold Canyon Arizona Posts: 4,372	Re: What did you do to your truck today! got the cab on frame... Attached Images __________________ 1971 K5 CST Blazer 1951 -3100 5 window short bed 4sp 1965 Chevelle Malibu 283 (sadly sold) 1968 Camaro 327 1968 Honda mini-trail z50a #377 1966 uh 1-D Huey

07-17-2010, 10:38 PM	#494
67Slider Registered User Join Date: Mar 2010 Location: Pueblo West, CO Posts: 944	Re: What did you do to your truck today! The boy and I put the fan shroud and fan back in, [IMG][/IMG] replaced the old MC (no leaks this time), [IMG][/IMG] started putting in the B&M mega shifter, Put the driver door back together, [IMG][/IMG] DAMN HOT!!!! 103 today in Colorado so I would work a bit and cool off, repeat, repeat and repeat! Yote1234 - I dig that paint job!!!! Very nice! __________________ 67 C10 Stepside 66 Mustang Coupe 99 Burb 2500

07-17-2010, 10:53 PM	#495
bddcustoms Registered User Join Date: Apr 2009 Location: Bowie, Maryland Posts: 80	Re: What did you do to your truck today! drilled some spot welds out on the cab -- only had a few minutes to play today. __________________ broke d!@k dog Garage 1969 C20 - Project: "Big Sexy" [http://67-72chevytrucks.com/vboard/s...d.php?t=454894] 2003 'Burban - [Big Pop's daily driver] 1969 350/350 Stingray - [as soon as the economy turns...] 1939 Chevy Roadster Pick Up - Project: "Pre-School" (searching now)

07-17-2010, 11:05 PM	#496
oldblue1968chevy Grandpa in the rustmobile... Join Date: Nov 2008 Location: Spokane WA/Viola TN Posts: 11,422	Re: What did you do to your truck today! wire wheeled greasy bolts/brackets off gettin' ready for painting sometime soon! __________________ John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4

07-17-2010, 11:08 PM	#497
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,608	Re: What did you do to your truck today! I swept around the 72 and am doing brakes right now on the blazer.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

07-17-2010, 11:08 PM	#498
yote1234 Senior Member Join Date: Feb 2003 Location: Gold Canyon Arizona Posts: 4,372	Re: What did you do to your truck today! 67slider... your looks great also. so you only hit 103? we hit 116 and at 8.00 pm were still over 100 deg. thats hot... again...nice paint.. __________________ 1971 K5 CST Blazer 1951 -3100 5 window short bed 4sp 1965 Chevelle Malibu 283 (sadly sold) 1968 Camaro 327 1968 Honda mini-trail z50a #377 1966 uh 1-D Huey

07-17-2010, 11:18 PM	#499
willys72fleetside Registered User Join Date: Jul 2010 Location: Curtice,OH Posts: 81	Re: What did you do to your truck today! Didn't have much time but was able to get the seat adjuster wire run from side to side. Every little bit helps! __________________ A USED TRUCK IS A LOVED TRUCK!

07-17-2010, 11:27 PM	#500
marks1972 Registered User Join Date: May 2010 Location: Atoka, TN Posts: 240	Re: What did you do to your truck today! Took mine to a local Cruz in. Just hapened to drive by it. I didn't even know we had them down here. Come to find out we do every Sat night. __________________ Mark 1968 C-10 SWB 307/munci 4spd/411possi 1986-1990 1972 Cheyenne-10 LWB 350/TH350 IF SHE WHOULD HAVE KEEPT THE SHIRT ON THEY WOULDNT HAVE BROKEN UP THANKS ADAM SANDLER U. S. Navy Seabee "CAN DO", "The difficult we do at once. The impossible may take a little bit longer.","We Build We Fight", "Work Hard Play Hard"

Register or Log In To remove these advertisements.