Project: Bad Bagged '68.5

[babyblueoval]

Originally Posted by 67cheby

I'm...... And where is your build thread ? I must be missing it ? How fast is your progress going ?? Lol , ya like apples , how do you like those apples ?? Lol
Posted via Mobile Device

I almost added in that I hadn't even started mine but I figured I'd give you the chance to give me a hard time back.

[67cheby]

Lol
Posted via Mobile Device

[67c10rustbuket]

I say do it like Cheby's if you want the detail of the inner body line.

VA's idea is pretty slick too.

I think i'll do mine like NACHO truck. looks like delmo just unbolted everything and reinstalled the floor 10" or so higher. Im sure its more complicated than typing that though.

[jlaird]

The way I want to do it is so the upper body line is eliminated since the tub will extend above that. Thanks for the replies. Something to think about today at the day job. Rather be working on the truck!
Posted via Mobile Device

[N2TRUX]

If you can create new panels, as well as simulate the stock lines why not makes them follow the wheel tub. That will give you the strength in the panel and look correct too.

[jlaird]

Originally Posted by N2TRUX

If you can create new panels, as well as simulate the stock lines why not makes them follow the wheel tub. That will give you the strength in the panel and look correct too.

That's my plan. Sometimes its hard to describe what you mean in writing.

[67cheby]

i made my front panel to match the side panels

[hotrod1]

Nice. Can you lay out how you did it? Do you have a shear, brake, etc? Is there somewhere we can go to see more demos on metal fab like you are doing?

[jlaird]

this is what I'm planning:

[jlaird]

Got my rear wheel wells finished(tacked) this past weekend. For the top part where metal had to be added, I used a pair of original wheel tubs that I had. With a little massaging, the front part where the body line is fit really nice, however the rear 90 degree bend was too tight of a radius so I had to make a new piece for that area. Come out pretty good for bending metal in a vise with a hammer!



Dont look at those corners where I blew through with the welder!

[gringoloco]

I've had this same thought. Kindof a combination of yours and VA's. Would be simple enough to roll in a body line, break a flange for the floor, and provide a little room for wider meatss. Go for it and show is how it's done...

Tubs look good!

Posted via Mobile Device

[jlaird]

Originally Posted by gringoloco

I've had this same thought. Kindof a combination of yours and VA's. Would be simple enough to roll in a body line, break a flange for the floor, and provide a little room for wider meatss. Go for it and show is how it's done...
Posted via Mobile Device

will do!

[67cheby]

Looks great
Posted via Mobile Device

[cflvulcan]

Josh your truck is turning out amazing! I wana stop up and see it again but everytime im in your area I usually have a 53' foot trailer behind me lol.
Posted via Mobile Device

[jlaird]

Originally Posted by cflvulcan

Josh your truck is turning out amazing! I wana stop up and see it again but everytime im in your area I usually have a 53' foot trailer behind me lol.
Posted via Mobile Device

Whatcha hulling?
Posted via Mobile Device

[cflvulcan]

Haul all different kinds of stuff around the northeast. I always cut thru near johnstown when coming home from vt. Ill actually be at walmart dc by you tomorrow morning lol.
Posted via Mobile Device

[72BlckButy]

Amazing work on those tubs!

[cflvulcan]

I may have missed it but what color are you gona paint it?
Posted via Mobile Device

[jlaird]

Originally Posted by cflvulcan

I may have missed it but what color are you gona paint it?
Posted via Mobile Device

One of my many indecisions. Probably either gold/white or an olive green/white. At first I was dead set on a white roof, but I am going to install the lower body trim, and I think the white below it looks nice without the white roof.
Posted via Mobile Device

[jlaird]

I started my inner bed panels. I decided to rework the existing ones rather than try to make new. I thought getting the recessed stepped body lines just right would be near impossible...for me anyway. So with a little thought, I came up with the idea of cutting the ends of the panels off and flipping them. (you will see what I mean in the pics) This is all in an effort to keep the body lines flowing with the wheel tubs.

First thing to do was to adjust the arch in the bedside to the new shorter wheel tub. Here is a scribe line where I made my first incision!


And piece removed


Heres the beginnings of the new piece going in. I put a bead roll in it to aid in the part that will be rolled at the edge. I will cut down the middle of the bead roll and hammer it over.


Here it is cut


and with nuts welded to the backside to bolt to the wheel tub


and tacked in place. at this point, I removed part of the panel(the part that I need) from the bedside so that I can get a dolly behind the panel better.


Here is the part at the end of the panel that will be cut off.


cut


and flipped


This is the only piece I really needed tacked in place


And the rest a new piece of metal.


finished welding!




Next I have to do the other end of the panel, then bring the whole panel to someone with an 8 foot break to make the flange on the top so it can be spot welding in just like it came from the factory.

[67cheby]

Cool !
Posted via Mobile Device

[kvn1011]

Nice!!!

[brans72]

Who makes that bead roller and any more info on it? Thanks

[jlaird]

Originally Posted by brans72

Who makes that bead roller and any more info on it? Thanks

It's just a harbor freight beefed up.
Posted via Mobile Device

[67c10rustbuket]

Originally Posted by jlaird

I started my inner bed panels. I decided to rework the existing ones rather than try to make new. I thought getting the recessed stepped body lines just right would be near impossible...for me anyway.

Don't be so modest, You are a metal magician! very nice work as always. I cant wait to see the finished bed. You da man!