|
10-04-2012, 10:37 AM | #1 |
Registered User
Join Date: Aug 2010
Location: Keller TX
Posts: 836
|
Re: What did you do to your truck today?
Re balanced the front tires and put duc tape over the inner sticky weights to keep them on.. LOL lost the fist set and man did it shake.
__________________
62 long box with a little SBC http://www.67-72chevytrucks.com/vboa...d.php?t=510631 http://good-times.webshots.com/album/561798652HdwqzG |
10-04-2012, 11:27 AM | #2 |
Registered User
Join Date: Sep 2012
Location: Boise, ID
Posts: 57
|
Re: What did you do to your truck today?
Sweet 383. How much lead are you going to hide under the truck bed so you can keep your tires hooked to the pavement?
__________________
62 C10, LWB fleetside, 350SBC, Munie 4spd, |
10-04-2012, 11:29 AM | #3 |
Registered User
Join Date: Aug 2010
Location: Keller TX
Posts: 836
|
Re: What did you do to your truck today?
With sticky tires these trucks will hook up very hard, with nothing more than some soft rear shocks..
__________________
62 long box with a little SBC http://www.67-72chevytrucks.com/vboa...d.php?t=510631 http://good-times.webshots.com/album/561798652HdwqzG |
10-04-2012, 11:34 AM | #4 |
Registered User
Join Date: Nov 2008
Location: Houston TX
Posts: 362
|
Re: What did you do to your truck today?
not planning on smoking the wide whites to many times....those things were not cheap you know..
__________________
The price of cool aint cheap. |
10-04-2012, 09:41 PM | #5 |
Registered User
Join Date: Dec 2011
Location: Blytheville/Bentonville, AR
Posts: 393
|
Re: What did you do to your truck today?
Yesterday pulled the rear axle to get ready for cnotch and 2.73 swap...
Posted via Mobile Device |
10-04-2012, 09:58 PM | #6 |
Registered User
Join Date: Feb 2010
Location: Hartselle, Al.
Posts: 466
|
Re: What did you do to your truck today?
I decided to replace all the steel brake lines with stainless so I picked up a double flaring kit to go with my tubing bender. Also got a second angle grinder cause I am really sick of switching out wheels right in the middle of a project.
I finally got the rear end clean enough to paint. That'll get done Saturday morning. Steven
__________________
“Life is and will ever remain an equation incapable of solution, but it contains certain known factors.” - Nikola Tesla Matt. 6:27 "Who of you by worrying can add a single hour to his life?” http://www.67-72chevytrucks.com/vboa...=507266&page=2 |
10-04-2012, 10:05 PM | #7 |
Registered User
Join Date: Sep 2012
Location: Lawton Oklahoma
Posts: 308
|
Re: What did you do to your truck today?
Still fighting with new door seals, attempting to re adjust doors
Posted via Mobile Device
__________________
People who make excuses didn't want to do it in the first place! http://s1326.photobucket.com/albums/...cpZZ1QQtppZZ16 |
10-05-2012, 05:41 AM | #8 |
Registered User
Join Date: Jul 2012
Location: UAE
Posts: 85
|
Re: What did you do to your truck today?
Good day so far, I finished inside my cab today; dash - wooden bezel, wooden clock/radio holder, new knobs, handle for glove compartment (old harley davidson bolt), rubber door lining installed one side, new seat belts installed, A/C vents painted and reinstalled, and GMC door sill plates installed.
_________________________________ http://67-72chevytrucks.com/vboard/s...d.php?t=538792 |
10-05-2012, 09:03 AM | #9 |
Registered User
Join Date: Sep 2012
Location: Boise, ID
Posts: 57
|
Re: What did you do to your truck today?
scoured internet and catalogs looking for all of the upgrades I am going to do. Stuck mainly on the type of disc bake conversion. Transplant crossmember and rear to get 5 lug but lose the torsion setup or go with a commercial 6 lug kit up front.........
__________________
62 C10, LWB fleetside, 350SBC, Munie 4spd, |
10-06-2012, 09:20 AM | #10 |
Registered User
Join Date: Sep 2008
Location: southdakota
Posts: 179
|
Re: What did you do to your truck today?
made a hood...well kinda
__________________
1960 chevy 4.6 police interceptor chassis under this bad boy with 24 inch lexani's |
10-06-2012, 11:22 AM | #11 |
Who Me?
Join Date: Sep 2010
Location: Royal Palm Beach, FL
Posts: 4,067
|
Re: What did you do to your truck today?
Today I replaced the guages in the dash, well under the dash.
Before New guages After Just trying to get things to look more uniform.
__________________
Steve 1997 Tahoe LT 4D 2WD (DD) 2001 Blazer 4D 2WD 1961 Apache 10 (sold) 1965 C10 Stepper (sold) |
10-06-2012, 01:15 PM | #12 |
Registered User
Join Date: Dec 2011
Location: Creighton Sask. Canada
Posts: 4,121
|
Re: What did you do to your truck today?
Gauge cluster looks good, fits in well with the switchs.
|
10-06-2012, 01:38 PM | #13 |
Who Me?
Join Date: Sep 2010
Location: Royal Palm Beach, FL
Posts: 4,067
|
Re: What did you do to your truck today?
Thanks!!
__________________
Steve 1997 Tahoe LT 4D 2WD (DD) 2001 Blazer 4D 2WD 1961 Apache 10 (sold) 1965 C10 Stepper (sold) |
10-06-2012, 10:18 PM | #14 |
GMC's n H.D.'s too!
Join Date: Oct 2010
Location: Nampa, Idaho
Posts: 1,583
|
Re: What did you do to your truck today?
Finished sanding and painting the gas tank.
Then finished sanding the back half of the cab and primered it. |
10-07-2012, 01:31 AM | #15 |
Registered User
Join Date: Sep 2012
Location: Boise, ID
Posts: 57
|
Re: What did you do to your truck today?
Found out the mirror shakes a whole lot less when all three screws are tight!
__________________
62 C10, LWB fleetside, 350SBC, Munie 4spd, |
10-07-2012, 01:52 AM | #16 |
Senior Enthusiast
Join Date: Feb 2007
Location: Spokane Valley, WA
Posts: 8,356
|
Re: What did you do to your truck today?
Spent the day re-reading everything I can find about actually installing the windshield. Half the success stories install the windshield top first, while the rest start bottom first. I sure wish there was a pictorial posting already in place specific to the 60-63 wrap around windshield. The factory service manual is practically worthless because it offers no installation photos and doesn't address the issue of the glass hitting the roof overhang.
__________________
My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=444502 |
10-07-2012, 02:12 AM | #17 |
Registered User
Join Date: Jul 2005
Location: AL
Posts: 1,828
|
Re: What did you do to your truck today?
There is a very good video on this site. Recently done. Major provider. They installed the top first. Someone has a link I am sure
Posted via Mobile Device
__________________
" |
10-07-2012, 09:54 AM | #18 |
Registered User
Join Date: Dec 2009
Location: Orlando, Florida
Posts: 427
|
Re: What did you do to your truck today?
cut, weld, grind, repeat.
__________________
|
10-07-2012, 09:23 PM | #19 |
Registered User
Join Date: Oct 2012
Location: Chula Vista, ca
Posts: 48
|
Re: What did you do to your truck today?
For my 66 I installed electronic ignition conversion, replaced the turn signal assembly and rebuilt my leaky Carter yf carburetor.
|
10-07-2012, 09:49 AM | #20 |
Registered User
Join Date: Jul 2012
Location: Spanish Fork, Ut
Posts: 10
|
Re: What did you do to your truck today?
I rebuilt the speedo from junk yard parts, installed a new heater blower motor out of a 77 ford f250 fit perfectly, i had to take the motor out of the ford mount and put it in my stock mount the 62 squirrel cage fit on the shaft fine. put in a new tach.
here are the pictures of my 62 finally have some computer time. |
10-07-2012, 10:53 PM | #21 |
Registered User
Join Date: Jun 2012
Location: Nashvegas
Posts: 45
|
Re: What did you do to your truck today?
Took the week off and got quite a bit done. Still a long way to go... Lots of pics along the way here: http://bikerswag.wordpress.com/category/66-stepside/
__________________
Check out my BLOG to learn more about my truck project: CLICK HERE |
10-08-2012, 12:08 AM | #22 |
Registered User
Join Date: Feb 2010
Location: Hartselle, Al.
Posts: 466
|
Re: What did you do to your truck today?
Didn't get much done this weekend.
My 11 year old welded up a couple holes in bed cross members so we can reuse them for the flat bed. Steven
__________________
“Life is and will ever remain an equation incapable of solution, but it contains certain known factors.” - Nikola Tesla Matt. 6:27 "Who of you by worrying can add a single hour to his life?” http://www.67-72chevytrucks.com/vboa...=507266&page=2 |
10-08-2012, 01:57 AM | #23 |
Registered User
Join Date: Sep 2009
Location: California Delta
Posts: 2,163
|
Re: What did you do to your truck today?
I bought a chrome rear bumper that was on craigslist. The guy didn't know if it was original or aftermarket so I made the 60 mile drive and found it was an older Chinese aftermarket bumper but I bought it anyway at a reduced price. I ordered up bumper and license plate brackets from Classic Industries. After modifying 1 bumper bracket and the plate bracket I got the bumper mounted today. It's not running to good right now but it looks a little nicer.
__________________
Name: Rich Current Ride: 1964 C-10 Short Fleetside Daily Driver: 2005 GMC crew cab short fleetside /2001 Chevy Tahoe Past GM Trucks: 1959 GMC short stepside 1968 GMC short stepside-4x4 1973 Chevy short stepside 1989 Chevy short fleetside-reg cab 1993 Chevy short fleetside-Xcab 2002 Chevy short fleetside-Xcab Save the dinosaurs, use synthetic oil. |
10-08-2012, 04:21 PM | #24 |
Registered User
Join Date: Aug 2011
Location: Bury St Edmunds, UK
Posts: 215
|
Re: What did you do to your truck today?
Just a small job but has made a big difference to my interior - and something I've wanted to do for the past two years..
Many thanks to Jeff [62 Longbed] who sent all of the necessary parts to mount my horn button (including the button itself!) across the pond for a great price
__________________
Barney, in the UK 1962 Chevy C20 1974 Ford Econoline 1987 Peugeot 205 GTi 1991 Peugeot 205 GTi |
10-08-2012, 11:56 PM | #25 |
Registered User
Join Date: Jul 2012
Location: UAE
Posts: 85
|
Re: What did you do to your truck today?
I put in the seats and did some general work on the interior cab... later will put on the newly chromed bumper!
cheers _______________________________ http://67-72chevytrucks.com/vboard/s...d.php?t=538792 |
Bookmarks |
|
|