![]() |
|
![]() |
#1 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
Onwards Comrades!
|
![]() |
![]() |
![]() |
#2 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
"The Paper Towel is mightier than the pen which is mightier than the sword" ~ Said No One Ever!
|
![]() |
![]() |
![]() |
#3 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
after carefully considering using high heat BBQ or header paint on the hood belly I decided to shoot it with the paint I already had!
I (and some of youz) really like this Semi-Flat Crayola secret sauce |
![]() |
![]() |
![]() |
#4 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
looking much better already and this is only after the first coat, since the surface was dark already you get roughly two coats per can
Top Tip: if you don't like white fuzzies on your surface than it's ok to clean with paper towels but don't rely on them for your final wipe down, use something else Note: the cross flow ventilation in the dishwasher safe organic paint booth (yes I still wore a breathing mask in order to protect my brain cells, yes both of them) |
![]() |
![]() |
![]() |
#5 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
we start our Annual Labor Day: Labor of Love Project with a scrap piece of 16 or 18(ish) gauge steel
we square it off a bit and cut it into semi equal rectangular pieces (blowing our 8th grade geometry teachers mind) Last edited by Gregski; 09-03-2018 at 04:06 PM. |
![]() |
![]() |
![]() |
#6 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
next we take the CAD blueprinted scrap piece to the organic metal brake where we divide it into two
Last edited by Gregski; 09-03-2018 at 04:06 PM. |
![]() |
![]() |
![]() |
#7 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
I did say "semi" even (we will trim them down to eveness later)
Top Tip: The key to any successful project is controlling user/audience expectations, ha ha Last edited by Gregski; 09-03-2018 at 04:05 PM. |
![]() |
![]() |
![]() |
#8 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
at this point my cousin Joe Goodenoff showed up (think National Lampoon's Vacation cousin Eddie) and said "lemme show you something... hold my beer"
and he took an ordinary grade 5 bolt and proceeded to decapitate it... Last edited by Gregski; 09-03-2018 at 04:04 PM. |
![]() |
![]() |
![]() |
#9 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
then he took it to the Bead Roller Free bead roller station
|
![]() |
![]() |
![]() |
#10 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
and then on to the Quality Assurance Station - QAS
Last edited by Gregski; 09-06-2018 at 12:40 AM. |
![]() |
![]() |
![]() |
#11 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
alright that's impressive, but what in the world are you [ahem] is Joe makin'?
Last edited by Gregski; 09-06-2018 at 12:41 AM. |
![]() |
![]() |
![]() |
#12 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
rinse, lather, repeat...
|
![]() |
![]() |
![]() |
#13 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
ladies and gentlemen, the Taco Hood Struggle is real!
and although LMC Truck sells these as a "Hood Brace Kit" for $20 bucks, it is honestly a joke and I rather roll my own |
![]() |
![]() |
![]() |
#14 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
don't worry I used a piece of flat ply wood underneath not to dent or scratch da hood
|
![]() |
![]() |
![]() |
#15 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
not too bad, I grounded the welds down a bit but not totally flat so that I wouldn't weaken the welds nor be unable to find them later if I needed to drill them out (that's my excuse anyway)
shot sum primer and ready for paint Last edited by Gregski; 09-06-2018 at 12:42 AM. |
![]() |
![]() |
![]() |
#16 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
then it was on to the other side and the whole reason why we is doin' this in the first place
this side already developed a hairline crack in the safety fold, so I bugger welded it up and just like on the other side we ground the surface to bear bare (?) metal prior to welding |
![]() |
![]() |
![]() |
#17 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
tell me if this has ever happened to you: with two spot welds left we ranned out of welding wire?
|
![]() |
![]() |
![]() |
#18 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
but I wasn't gonna let this stop me, so I replaced the Lincoln .035 artillery with the .025 caliber (i.e. all that I had on hand) and grabbed the gun for the home stretch
I must say I like how the .025 lays down spot welds, now I'm sure if I knew how to fandangle the knobs on Big Red properly I could achieve the same results with the .035 but still the .025 agrees with me just the same |
![]() |
![]() |
![]() |
#19 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
since this project was sapposed to be done in August, with the paint still wet I hollered at my soon to be 17 millenial to come downstairs and help me flip this pancake over
we're gonna lossen up that surface rust with some 220 sand paper |
![]() |
![]() |
![]() |
#20 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
a little stare and compare, what a difference 5 minutes with the orbital sander makes
and then it was time for some Phosphoric acid treatment from Home Depot ($5.00, I'm looking at you $25 dollar Metal Re$cue), this is the potion I should have used the first time on my original hood, but I messed up and used muriatic acid instead (stupid me, should have paid more attention in Chemistry class) Last edited by Gregski; 09-03-2018 at 08:48 PM. |
![]() |
![]() |
![]() |
#21 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
and here it is after the acid treatment and the baking soda neutralizing bath, man I wish the rest of the truck looked like this, I would just leave it, I like this [ahem] "patina"
|
![]() |
![]() |
![]() |
#22 |
Registered User
Join Date: Jun 2004
Location: Medford,Oregon
Posts: 390
|
Re: Restoring Rusty
I am thoroughly impressed good sir
__________________
![]() |
![]() |
![]() |
![]() |
#23 |
Post Whore
![]() Join Date: Aug 2014
Location: Sacramento, CA
Posts: 10,835
|
Re: Restoring Rusty
|
![]() |
![]() |
![]() |
#24 |
Moderator
![]() Join Date: Oct 2008
Location: Wentworth, NH
Posts: 4,954
|
Re: Restoring Rusty
Joe Goodenuff huh...
__________________
1959 M35A2 LDT465-1D SOLD 1967 Dodge W200 B383, NP420/NP201 SOLD 1969 Dodge Polara 500 B383, A833 SOLD 1972 Ford F250 FE390, NP435/NP205 SOLD 1976 Chevy K20, 6.5L, NV4500/NP208 SOLD 1986 M1008 CUCV SOLD 2000 GMC C2500, TD6.5L, NV4500 2005 Chevy Silverado LS 2500HD 6.0L 4L80E/NP263 2009 Impala SS LS4 V8 RTFM... GM Parts Books, GM Schematics, GM service manuals, and GM training materials...
And please let us know if and how your repairs were successful. Last edited by hatzie; 09-06-2018 at 01:35 AM. |
![]() |
![]() |
![]() |
#25 |
Registered User
Join Date: May 2013
Location: Clay City, KY
Posts: 40
|
Re: Restoring Rusty
Looks good thanks for the updates
__________________
And in the end, it’s not the years in your life that count. It’s the life in your years.” — Abraham Lincoln |
![]() |
![]() |
![]() |
Bookmarks |
|
|