![]() |
|
![]() |
#1 |
Registered User
Join Date: Apr 2017
Location: Ragley, La.
Posts: 137
|
Re: What did you do to your truck today part IV
Cleaned up the engine bay. Getting ready to install cast headers and Clifford manifold.
|
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jan 2016
Location: Barber City, CA
Posts: 4,781
|
Re: What did you do to your truck today part IV
this thread needs more rust
![]() got the sill plates off, installed the dome light, mat, and seat.. had to cut a few screws and chase a lot of threads but it all went together fairly decent I think.. little trick I'll share in case someone hasn't seen it; ![]() ![]() ![]() ![]() the truck shop mat went down pretty easy and most of the holes lined up with the impressions on the back.. especially pleased how well it sits in there since I dropped it right on the bare floor without tar or foam or anything yet.. $10 harbor freight gasket punch kit is probably spent, but did the trick for the mat and the seat.. even cleaned up all of the original pedal pads.. wd40 and steel toothbrush to clean and stand up a little fur to cut the gloss.. de-greased with 409 to get that squeaky, non-slip finish back.. my 6yo took some of these while I was trimming and fitting.. ![]() ![]() ![]() ![]() ![]() the seat story about this fabric from SMS has been beat to death so I'll spare everyone.. but the work Mando from San Pedro did putting it together is great, really comfortable seat.. and while I was cleaning all of the mechanisms and lubing the tracks, found what I think is a date.. all of the LOF glass is dated Feb or Mar 65 so 2/8/65 would fit, anyone know about this? ![]() ![]() ![]() ![]() kids dig it! they took turns driving ![]() ![]() ![]()
__________________
I started out with nothing - and I still have most of it Last edited by Killer Bee; 05-21-2018 at 08:11 PM. Reason: correction for jute |
![]() |
![]() |
![]() |
#3 |
Registered User
![]() Join Date: Jan 2017
Location: hastings, ne
Posts: 81
|
Re: What did you do to your truck today part IV
got truck back from paint today
|
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Apr 2012
Location: Cambridge, Ontario, Canada
Posts: 1,771
|
Re: What did you do to your truck today part IV
Exciting! Looks reeeeally nice!
__________________
Craigerrr My build thread, CRGRS 66 Winter Build: http://67-72chevytrucks.com/vboard/s...09#post5638709 |
![]() |
![]() |
![]() |
#5 |
Registered User
![]() Join Date: Jan 2017
Location: hastings, ne
Posts: 81
|
|
![]() |
![]() |
![]() |
#6 |
1962 C-10
Join Date: Apr 2005
Location: Las Vegas, New Mexico
Posts: 4,978
|
Re: What did you do to your truck today part IV
Looks good!
![]()
__________________
Joseph Chavez ![]() "See the USA in a Chevrolet!!" ......................_____ .........________//__{\_____ ,,,,,,,/__(O)___//___/__(O)_/ 1962 C10 Shortbed Fleetside 327/th350 GV overdrive 1974 C10 Longbed Fleetside 350/th350 "The Trash Truck" 1999 Chevy 2500 OBS, Longbed 5.7/4L80E 4x4 2015 GMC Sierra SLE 1500 4x4 |
![]() |
![]() |
![]() |
#7 |
Registered User
![]() Join Date: Jan 2017
Location: hastings, ne
Posts: 81
|
Posted via Mobile Device
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Nov 2008
Location: Lacombe, LA
Posts: 2,772
|
Re: What did you do to your truck today part IV
I'm retiring in Feb. '19 My new hobby will be religious chemistry, turning wine and into water.......
__________________
http://s1299.photobucket.com/user/jb...23904108567829 |
![]() |
![]() |
![]() |
#9 |
Senior Member
![]() ![]() ![]() Join Date: Jan 2018
Location: Hickory Flat, GA
Posts: 4,468
|
Re: What did you do to your truck today part IV
Started prepping some parts for paint over the past couple days, and got some parts to get the engine back together. Hoping to make at least the Atlanta stop of Power Tour this year. Going to shoot some color in the next couple of days hopefully.
![]()
__________________
Christian Carpenter 1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive Overdrive wiring here1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson |
![]() |
![]() |
![]() |
#10 |
Senior Member
![]() Join Date: Nov 2015
Location: Seligman, MO
Posts: 626
|
Re: What did you do to your truck today part IV
Prepped the bed for Upol Raptor Liner. I have a beat up steel bed floor from a '71 c10 and this should make it look so much better!
|
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Apr 2017
Location: Ragley, La.
Posts: 137
|
Re: What did you do to your truck today part IV
From the seat to the engine bay.
Installed the Clifford intake, 2 barrel Holley and Langdon headers. Tomorrow I need to visit the guy at the hydrolic shop, who is going to make up some braided hoses for the intake water jacket. Then to Meineke to do the exhaust. I also have the lower thermostat housing, that's in the photo on the seat, to install. It has two holes on the sending unit side so I can plumb the hot water from there. |
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Jan 2011
Location: Tulare, CA
Posts: 733
|
Re: What did you do to your truck today part IV
Sweet!
|
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Jan 2016
Location: Barber City, CA
Posts: 4,781
|
Re: What did you do to your truck today part IV
chased speedo nut back up to top end of cable after removing/re-installing new mat
![]() cleaned and lubed both side vents and glove box latch.. drank copious amounts of beer and cleaned off some benches of small parts today ![]()
__________________
I started out with nothing - and I still have most of it |
![]() |
![]() |
![]() |
#14 |
Senior Member
![]() Join Date: Nov 2015
Location: Seligman, MO
Posts: 626
|
Re: What did you do to your truck today part IV
Finally sprayed the Upol Raptor bed liner. I sanded, cleaned, and sprayed Upol's Acid primer #8 prior to laying it down. It was super easy and looks great. It will be a week or so before I can test it out, though.
The bed floor is from a '71, I believe, and beat to hell, but it was free. I do not like the wood beds. |
![]() |
![]() |
![]() |
#15 |
Registered User
Join Date: Dec 2009
Location: Rockwall Texas
Posts: 79
|
Re: What did you do to your truck today part IV
Installed fiberglass smooth dash. No switches, no nothing except 6 gauges. Will repaint to match console later.
|
![]() |
![]() |
![]() |
#16 |
Moderator
![]() ![]() Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
|
Re: What did you do to your truck today part IV
You can't just drop that and leave. Who made the dash? Where did you buy it?
__________________
Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats? |
![]() |
![]() |
![]() |
#17 |
Registered User
Join Date: Dec 2009
Location: Rockwall Texas
Posts: 79
|
Re: What did you do to your truck today part IV
This fiberglass dash for 60-66 C10 was purchased from US Body Source. Around $300 bucks plus shipping of $150. Took 8 weeks to receive it and comes very very rough. It needed a lot of work fitting and smoothing to get ready for paint. When it is all done I think it will be awesome, but if I had to do again for the price and work, probably not. Probably just weld on the original.
Last edited by lowslow64; 06-12-2018 at 10:47 AM. |
![]() |
![]() |
![]() |
#18 |
Post Whore
![]() Join Date: Mar 2013
Location: Southern Oregon
Posts: 10,384
|
Re: What did you do to your truck today part IV
Installed the mid shift kit on the tremec this evening. Now the shifter won't be under the cab floor anymore.
__________________
1966 Chevy C10 "Project Two Tone" http://67-72chevytrucks.com/vboard/s...d.php?t=596643 1964 GMC "Crustine" semi-build:http://67-72chevytrucks.com/vboard/s...d.php?t=665056 My youtube channel. Username "Military Chevy": https://www.youtube.com/channel/UC_h...fzpcUXyK_5-uiw |
![]() |
![]() |
![]() |
#19 |
Post Whore
![]() Join Date: Mar 2013
Location: Southern Oregon
Posts: 10,384
|
Re: What did you do to your truck today part IV
Got the trans installed and both inner fenders painted.
__________________
1966 Chevy C10 "Project Two Tone" http://67-72chevytrucks.com/vboard/s...d.php?t=596643 1964 GMC "Crustine" semi-build:http://67-72chevytrucks.com/vboard/s...d.php?t=665056 My youtube channel. Username "Military Chevy": https://www.youtube.com/channel/UC_h...fzpcUXyK_5-uiw |
![]() |
![]() |
![]() |
#20 |
Registered User
Join Date: May 2014
Location: Melbourne, FL
Posts: 297
|
Re: What did you do to your truck today part IV
Had my front fender, hood, grill, bumper and headlight straightened.
![]() ![]() |
![]() |
![]() |
![]() |
#21 |
Registered User
![]() Join Date: Jan 2017
Location: hastings, ne
Posts: 81
|
Re: What did you do to your truck today part IV
|
![]() |
![]() |
![]() |
#22 | |
Senior Member
![]() Join Date: Nov 2015
Location: Seligman, MO
Posts: 626
|
Re: What did you do to your truck today part IV
Quote:
|
|
![]() |
![]() |
![]() |
#23 |
Registered User
![]() Join Date: Apr 2011
Location: Ft. Worth, Tx
Posts: 536
|
Re: What did you do to your truck today part IV
This past Sunday we got all the wiring finished. Headlight, taillight and signals working. Only a few more things!
|
![]() |
![]() |
![]() |
#24 |
1965 Chevy C10, 2005 4.8L/4l60
![]() Join Date: Aug 2004
Location: DFW Texas
Posts: 8,541
|
Re: What did you do to your truck today part IV
Small update but big result soon...
__________________
Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684 ![]() ![]() ![]() support our troops! |
![]() |
![]() |
![]() |
#25 |
Senior Member
![]() Join Date: Feb 2014
Location: new smyrna beach fl / 29 palms cal
Posts: 1,727
|
Re: What did you do to your truck today part IV
Are you chrome plating your vent balls or are you painting them
|
![]() |
![]() |
![]() |
Bookmarks |
|
|