What did you do to your truck today? - Page 240 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

TehNewGuy · 12-30-2012, 11:55 PM

Finally tore out the fuel lines, tank and fuel pump. Cleaned the tank out (hose at the end of the sending line in the tank was deteriorated), then sanded the surface rust off to paint. Cleaned up the sending unit and buffed the metal a little. Fuel lines were rusted out so I replaced them with rubber hoses for now from under to cab to the pump. And fixed the leak on the fuel pump were someone slipped a wrench on a brass fitting and it wasn't sealing properly. (didn't know about that until i pulled it off, looked like the gasket went bad on the side and was leaking) Should prolly clean the rest of the back cab while I'm at it...

ABX131 · 12-30-2012, 11:58 AM

We finally got our steering columns switched and the electrical issues sorted out. Had to fab up the connecting rod from the column to the power steering box from two different rods. Need to order the shift linkage and move the shifter off the floor back to the column. New seat cover is in and looks great, stereo is next. Hoping to fab up the fan shroud before the end of the weekend as well. No rain for the next three days but it is cold! Jr goes back to school on Wednesday and we want as much done as possible.

1964Chevy · 12-30-2012, 02:35 PM

Welded the holes drilled in my homemade brackets for my rear LED lights so I can drill different holes. Sprayed primer on them, sanded the cups with 1000 paper.

Hx16457 · 12-31-2012, 11:06 AM

Yes, it goes under the bumper, and actually falls behind the fenders as well (by removing the 3inches from each side) I have it "dry mounted" currently. I took a few pics...
It is still really crapy outside, (snowing and now raining) and Sally (wife's name for my 65') doesn't go out in that kind of weather, so I had to take them in the garage.. I want to get her outside and get a good front shot with them powered up, for you guys!

Kind of this shot with out, then get one with..

Right now the pics are still on my Ipod, I'll have to add them to my photobucket and attach them here when I get near some wi-fi! Sorry... I will post later this afternoon so you guys can see the Finished product..

Oh and thanks for the instrest!

LDO · 12-31-2012, 06:24 PM

Not much really but with the kids out of school, I figured I'd pull my 12 yr old off his couch induced post Christmas tv/video game coma and get some fresh air and tinker in the garage a bit.

Here he is installing a pulley and cover on his mom's 283 going into her 57.

Truth be told, I could sit back and watch him learn and do stuff in the garage all day. Kind of stuff that makes a dad proud for sure.

greg65 · 12-31-2012, 09:48 PM

Quote:

Originally Posted by LDO

Not much really but with the kids out of school, I figured I'd pull my 12 yr old off his couch induced post Christmas tv/video game coma and get some fresh air and tinker in the garage a bit.

Here he is installing a pulley and cover on his mom's 283 going into her 57.

Truth be told, I could sit back and watch him learn and do stuff in the garage all day. Kind of stuff that makes a dad proud for sure.

Nice. I love spending time with the kids in the garage. It does not happen much with my twelve year old daughter but every time I work on the truck my ten year old son is there helping.
Posted via Mobile Device

LDO · 12-31-2012, 09:56 PM

great pic Greg!

greg65 · 12-31-2012, 10:23 PM

Quote:

Originally Posted by LDO

great pic Greg!

Thanks, maybe next time I came post it correctly.lol
Posted via Mobile Device

Hx16457 · 12-31-2012, 09:00 PM

Okay here are some pics after I got it mounted

I will get the wiring done and get her outside, if the flippen weather will let up!
Posted via Mobile Device

**TBONE1964** · 12-31-2012, 09:45 PM

Well I have made it back to Junction City OR for a couple of weeks and got a chance to work on my 64. I changed the hood from the original that was way to rotted around the front edge to a nicer one that has a few more dents. I can work with dents before rust. I also made some new battery cables that are routed a little different than factory. Most of the new cables is hidden. I think it really cleans up the look under the hood. It is a little chilly to paint here but I am getting some prep work done on the firewall and engine so it is ready.

I also donated the ugly 1964 canopy to scrap. It looks so much better without it.

I have to really plan my time well because I am only here for a short
Posted via Mobile Device

Mack B · 12-31-2012, 10:06 PM

Installed my new steering wheel

Posted via Mobile Device

LDO · 12-31-2012, 10:12 PM

Quote:

Originally Posted by Mack B

Installed my new steering wheel

Posted via Mobile Device

wow that's sweet! I like the look of the classic wheels in our trucks..

Mack B · 12-31-2012, 10:14 PM

Yea they ok, not quite as cool as a small block with three deuces tho

Posted via Mobile Device

LDO · 12-31-2012, 10:19 PM

LOL, maybe so Mack, but I tell you what, if you run across another steering wheel, let me know and if I run across another 3x2 setup, i'll let you know.

Crx150zc · 12-31-2012, 10:39 PM

I could not get my camera to work, Might have had some thing to do with the cold but I got Jimmys 5 lug axle conversion done and he is back on the ground and can roll again.

Vernski · 01-01-2013, 12:08 AM

Painted the core support behind the grill satin black and installed the grill after cleaning it good. The black makes the grill stand out better...Vernski

robber grin · 01-06-2013, 05:55 PM

I have been tearing a 66 C10 hood apart to see what it takes to do so and whether or not it might be salvagable...

Today I etch-primed most of my front end stuff that's been blasted, and had the bump-stops removed.

Trying to get going on my 62 C10...

donthekawguy · 01-08-2013, 12:29 AM

Quote:

Originally Posted by Vernski

Painted the core support behind the grill satin black and installed the grill after cleaning it good. The black makes the grill stand out better...Vernski

Hey Vern I was going to paint my truck lime green but now I can't. Since we live in the same town it wouldn't be cool. lol

Vernski · 01-08-2013, 01:30 AM

Quote:

Originally Posted by donthekawguy

Hey Vern I was going to paint my truck lime green but now I can't. Since we live in the same town it wouldn't be cool. lol

Sorry about that Don, actually the paint is called chartreuse it is almost yellow depending on the lighting under fluorescent it looks yellow. Is yours the one in your avatar? Now that looks cool cause I like flame jobs we should have a cup of joe sometime and talk trucks...Vernski

Gunster89 · 01-08-2013, 06:34 AM

today I unbolted the bell housing from my truck and now the old engine is ready to go and I got my motor today its a 350 with all 400 insides sweet motor now to repaint her add some new seals freeze plugs and possibly an oil pump while she is out might be smart has top of the line insides sweet setup cant wait

66-PMD-GMC · 01-06-2013, 06:14 PM

Put a new frame under a 66 big window truck...

gmcdeadhead · 01-06-2013, 06:29 PM

i replaced all the cooling lines , rebuilt the original carburetor , replaced the intake and exhaust gasket , on the 292 motor.

wutnxt · 01-06-2013, 07:19 PM

Well.....looked at this for about 30 mins and tried to decide which build o mine should get it

dantimdad · 01-06-2013, 08:19 PM

Neither one, dude. It should go in mine!

Steven

61_FL_Apache · 01-06-2013, 08:23 PM

I spent most of the afternoon smoking a nice beef roast to have with dinner. In my sights all that time was my truck!!

12-30-2012, 11:55 PM	#1
TehNewGuy Registered User Join Date: Nov 2012 Location: Miami, Fl Posts: 86	Re: What did you do to your truck today? Finally tore out the fuel lines, tank and fuel pump. Cleaned the tank out (hose at the end of the sending line in the tank was deteriorated), then sanded the surface rust off to paint. Cleaned up the sending unit and buffed the metal a little. Fuel lines were rusted out so I replaced them with rubber hoses for now from under to cab to the pump. And fixed the leak on the fuel pump were someone slipped a wrench on a brass fitting and it wasn't sealing properly. (didn't know about that until i pulled it off, looked like the gasket went bad on the side and was leaking) Should prolly clean the rest of the back cab while I'm at it... Attached Images __________________ 1966 Chevy C10 LWB Fleet- Project

12-30-2012, 11:58 AM	#2
ABX131 Registered User Join Date: Mar 2012 Location: Seattle,WA Posts: 317	Re: What did you do to your truck today? We finally got our steering columns switched and the electrical issues sorted out. Had to fab up the connecting rod from the column to the power steering box from two different rods. Need to order the shift linkage and move the shifter off the floor back to the column. New seat cover is in and looks great, stereo is next. Hoping to fab up the fan shroud before the end of the weekend as well. No rain for the next three days but it is cold! Jr goes back to school on Wednesday and we want as much done as possible.

12-30-2012, 02:35 PM	#3
1964Chevy Registered User Join Date: Jan 2012 Location: Denton, Texas Posts: 92	Re: What did you do to your truck today? Welded the holes drilled in my homemade brackets for my rear LED lights so I can drill different holes. Sprayed primer on them, sanded the cups with 1000 paper. Attached Images __________________ If your strength is small, don't carry heavy burdens. If your words are worthless, don't give advice. Chinese Proverb

12-31-2012, 11:06 AM	#4
Hx16457 Registered User Join Date: Sep 2012 Location: Lawton Oklahoma Posts: 308	Re: What did you do to your truck today? Yes, it goes under the bumper, and actually falls behind the fenders as well (by removing the 3inches from each side) I have it "dry mounted" currently. I took a few pics... It is still really crapy outside, (snowing and now raining) and Sally (wife's name for my 65') doesn't go out in that kind of weather, so I had to take them in the garage.. I want to get her outside and get a good front shot with them powered up, for you guys! Kind of this shot with out, then get one with.. Right now the pics are still on my Ipod, I'll have to add them to my photobucket and attach them here when I get near some wi-fi! Sorry... I will post later this afternoon so you guys can see the Finished product.. Oh and thanks for the instrest! __________________ People who make excuses didn't want to do it in the first place! http://s1326.photobucket.com/albums/...cpZZ1QQtppZZ16

12-31-2012, 06:24 PM	#5
LDO Registered User Join Date: Feb 2011 Location: Senatobia, MS Posts: 1,294	Re: What did you do to your truck today? Not much really but with the kids out of school, I figured I'd pull my 12 yr old off his couch induced post Christmas tv/video game coma and get some fresh air and tinker in the garage a bit. Here he is installing a pulley and cover on his mom's 283 going into her 57. Truth be told, I could sit back and watch him learn and do stuff in the garage all day. Kind of stuff that makes a dad proud for sure. Attached Images __________________ Once a Marine, always a Marine! My (Her) 57 Build "Beverly" My 66 Build "Betty" My 85 C10 "Old Blue" Help Me Find "Old Blue" OLD BLUE PART II

12-31-2012, 09:56 PM	#7
LDO Registered User Join Date: Feb 2011 Location: Senatobia, MS Posts: 1,294	Re: What did you do to your truck today? great pic Greg! __________________ Once a Marine, always a Marine! My (Her) 57 Build "Beverly" My 66 Build "Betty" My 85 C10 "Old Blue" Help Me Find "Old Blue" OLD BLUE PART II

12-31-2012, 09:00 PM	#9
Hx16457 Registered User Join Date: Sep 2012 Location: Lawton Oklahoma Posts: 308	Re: What did you do to your truck today? Okay here are some pics after I got it mounted I will get the wiring done and get her outside, if the flippen weather will let up! Posted via Mobile Device __________________ People who make excuses didn't want to do it in the first place! http://s1326.photobucket.com/albums/...cpZZ1QQtppZZ16

12-31-2012, 09:45 PM	#10
TBONE1964 Cluster King Join Date: Nov 2012 Location: Junction City, OR Posts: 5,263	Re: What did you do to your truck today? Well I have made it back to Junction City OR for a couple of weeks and got a chance to work on my 64. I changed the hood from the original that was way to rotted around the front edge to a nicer one that has a few more dents. I can work with dents before rust. I also made some new battery cables that are routed a little different than factory. Most of the new cables is hidden. I think it really cleans up the look under the hood. It is a little chilly to paint here but I am getting some prep work done on the firewall and engine so it is ready. I also donated the ugly 1964 canopy to scrap. It looks so much better without it. I have to really plan my time well because I am only here for a short Posted via Mobile Device Attached Images

12-31-2012, 10:06 PM	#11
Mack B Registered User Join Date: Apr 2012 Location: L.ower A.labama Posts: 518	Re: What did you do to your truck today? Installed my new steering wheel Posted via Mobile Device

12-31-2012, 10:14 PM	#13
Mack B Registered User Join Date: Apr 2012 Location: L.ower A.labama Posts: 518	Re: What did you do to your truck today? Yea they ok, not quite as cool as a small block with three deuces tho Posted via Mobile Device

12-31-2012, 10:19 PM	#14
LDO Registered User Join Date: Feb 2011 Location: Senatobia, MS Posts: 1,294	Re: What did you do to your truck today? LOL, maybe so Mack, but I tell you what, if you run across another steering wheel, let me know and if I run across another 3x2 setup, i'll let you know. __________________ Once a Marine, always a Marine! My (Her) 57 Build "Beverly" My 66 Build "Betty" My 85 C10 "Old Blue" Help Me Find "Old Blue" OLD BLUE PART II

12-31-2012, 10:39 PM	#15
Crx150zc Registered User Join Date: Dec 2012 Location: Colorado Springs, Co. Posts: 55	Re: What did you do to your truck today? I could not get my camera to work, Might have had some thing to do with the cold but I got Jimmys 5 lug axle conversion done and he is back on the ground and can roll again.

01-01-2013, 12:08 AM	#16
Vernski Registered User Join Date: May 2009 Location: Rathdrum, Idaho Posts: 1,135	Re: What did you do to your truck today? Painted the core support behind the grill satin black and installed the grill after cleaning it good. The black makes the grill stand out better...Vernski Attached Images

01-06-2013, 05:55 PM	#17
robber grin Registered User Join Date: Apr 2012 Location: Sunny Youngwood PA Posts: 463	Re: What did you do to your truck today? I have been tearing a 66 C10 hood apart to see what it takes to do so and whether or not it might be salvagable... Today I etch-primed most of my front end stuff that's been blasted, and had the bump-stops removed. Trying to get going on my 62 C10... Attached Images

01-08-2013, 06:34 AM	#20
Gunster89 Registered User Join Date: Jul 2011 Location: Prescott Arizona Posts: 66	Re: What did you do to your truck today? today I unbolted the bell housing from my truck and now the old engine is ready to go and I got my motor today its a 350 with all 400 insides sweet motor now to repaint her add some new seals freeze plugs and possibly an oil pump while she is out might be smart has top of the line insides sweet setup cant wait



Register or Log In To remove these advertisements.

01-06-2013, 06:14 PM	#21
66-PMD-GMC The 60-66 GMC/Pontiac guy.... Join Date: Oct 2010 Location: Apache Junction, Arizona Posts: 1,306	Re: What did you do to your truck today? Put a new frame under a 66 big window truck... __________________ Building Genuine Pontiac Firepowered cars and trucks for several decades. Why Pontiac?? That's just me daring to be different. Projects.. 63 C10 Short Wheel Base fleetside (The Pro-Street) currently under reconstruction. 440CID 2X4 Pontiac

01-06-2013, 06:29 PM	#22
gmcdeadhead Registered User Join Date: Jul 2007 Location: branchburg, new jersey Posts: 568	Re: What did you do to your truck today? i replaced all the cooling lines , rebuilt the original carburetor , replaced the intake and exhaust gasket , on the 292 motor.

01-06-2013, 07:19 PM	#23
wutnxt Registered User Join Date: Dec 2009 Location: vancouver b.c....is the biggest place most people would know but I am actually out in the valley 45 mins away Posts: 2,050	Re: What did you do to your truck today? Well.....looked at this for about 30 mins and tried to decide which build o mine should get it Attached Images __________________ 1966 Pro street build http://67-72chevytrucks.com/vboard/s...?t=448089[ 1958 LS 2 build http://67-72chevytrucks.com/vboard/s...d.php?t=527123 1966 SBFS low and go http://67-72chevytrucks.com/vboard/s....php?p=5799909 1966 SBFS street HULK http://67-72chevytrucks.com/vboard/s...=1#post5886625 Poject Low and go gets a 6.2 ltr LSA supercharged with 6 speed automatic Aluinum Radiator Dealer pm for details

01-06-2013, 08:19 PM	#24
dantimdad Registered User Join Date: Feb 2010 Location: Hartselle, Al. Posts: 466	Re: What did you do to your truck today? Neither one, dude. It should go in mine! Steven __________________ “Life is and will ever remain an equation incapable of solution, but it contains certain known factors.” - Nikola Tesla Matt. 6:27 "Who of you by worrying can add a single hour to his life?” http://www.67-72chevytrucks.com/vboa...=507266&page=2

01-06-2013, 08:23 PM	#25
61_FL_Apache Who Me? Join Date: Sep 2010 Location: Royal Palm Beach, FL Posts: 4,067	Re: What did you do to your truck today? I spent most of the afternoon smoking a nice beef roast to have with dinner. In my sights all that time was my truck!! __________________ Steve 1997 Tahoe LT 4D 2WD (DD) 2001 Blazer 4D 2WD 1961 Apache 10 (sold) 1965 C10 Stepper (sold)

Register or Log In To remove these advertisements.