![]() |
![]() |
#601 |
Registered User
Join Date: Mar 2013
Location: albuquerque New Mexico
Posts: 522
|
Re: What did you do with your truck today, Part 3
besides the newly dented passenger fender that's the only panel that needs attention. ow difficult was it to fit?
|
![]() |
![]() |
![]() |
#602 |
Registered User
Join Date: Aug 2016
Location: St George, Utah
Posts: 5
|
Re: What did you do with your truck today, Part 3
Evil- my cab (obtained up the road from you in Espanola, NM) had passenger damage to the toeboard, passenger inner fender and outer cowl panel. I replaced everything in there. The inner brace between the 2 panels was reproduction part and needed the most reworking. The outer cowl panel didn't need a whole lot of work, it was mainly the whole repair process in general. The cab was in much better shape than others I have seen.
Last edited by ItsJustMoney; 12-03-2017 at 11:29 PM. |
![]() |
![]() |
![]() |
#603 |
Registered User
Join Date: Mar 2013
Location: albuquerque New Mexico
Posts: 522
|
Re: What did you do with your truck today, Part 3
alright. I have been ignoring my truck for a couple of weeks in order to give it time to think about what it did. I was forced to address it tonight as it was parked under the attic and I was given orders by the boss to get the Christmas stuff down. new fuel filter, new needle & seat and it fired right up. this time (seems to change every time I start the thing) the fuel pressure was a tad low. I adjusted it and let it run on the high idle circuit for about 5 minutes then dropped it to the normal idle for another 5 minutes. I continually watched the sight windows and the pressure gauge. everything seemed fine. backed it out of the garage and let it idle for about 30 minutes while I was in the attic ( had my partner in crime check the pressure gauge every couple of minutes). the truck idled with perfect pressure and float levels for about 40 minutes total before I pulled it back in. I'm sad to say that the truck idling correctly without flooding and pulling in & out of the garage is a total win. I'm pretty happy in a pathetic kind of way. I guess we have to revel in the little victories.
|
![]() |
![]() |
![]() |
#604 |
Registered User
Join Date: Nov 2015
Location: Lebanon, Oregon
Posts: 35
|
Re: What did you do with your truck today, Part 3
Got my new calendar from "The Filling Station" in Lebanon, Oregon today. They put a picture of my truck on the May month. First time for me. Feels good.
__________________
1957 Chevy 3100 402 BBC 700R4 transmission c-4 Flat Out Engineering suspension |
![]() |
![]() |
![]() |
#605 |
Registered User
Join Date: Jul 2017
Location: Lebanon, Oregon
Posts: 241
|
Re: What did you do with your truck today, Part 3
Sounds like I need to make a trip over there tomorrow!
__________________
It was said that if you cut off one hydra head, two more grow back. -Lernaean Hydra Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=743246 |
![]() |
![]() |
![]() |
#606 |
Registered User
Join Date: Sep 2014
Location: USA
Posts: 2,249
|
Re: What did you do with your truck today, Part 3
I patched over the butchered steering column hole in my firewall, then cut a new properly-sized hole for my homemade column. Drilled the column shaft to accept a u-joint (using aircraft grade hardware) and mocked up the connection to the rack with a wooden dowel to get measurements. Ordered an appropriate length double D tonight. Tomorrow I'll fabricate a lower bracket to secure the bottom of the column.
|
![]() |
![]() |
![]() |
#607 |
Registered User
Join Date: Dec 2011
Location: Creighton Sask. Canada
Posts: 4,121
|
Re: What did you do with your truck today, Part 3
What engine are you running, just wondered how close the shaft will be to the exhaust when completed.
Mudman.
__________________
1987 Green n Green machine. 5.0 4spd std. 7" lift w 35's. |
![]() |
![]() |
![]() |
#608 |
Registered User
Join Date: Sep 2014
Location: USA
Posts: 2,249
|
Re: What did you do with your truck today, Part 3
Very astute observation. With an SBC, rams horn exhaust manifold did indeed conflict with the steering shaft. I switched to a rear dump manifold, giving me more than an inch of clearance. And yes, it's all been mocked up and test-fitted already.
Last edited by MiraclePieCo; 12-10-2017 at 04:02 AM. |
![]() |
![]() |
![]() |
#609 |
Registered User
Join Date: Oct 2011
Location: Pagosa Springs, CO
Posts: 162
|
Re: What did you do with your truck today, Part 3
That steering column has to be secured at the firewall. How did you secure it?
|
![]() |
![]() |
![]() |
#610 | |
Registered User
Join Date: Sep 2014
Location: USA
Posts: 2,249
|
Re: What did you do with your truck today, Part 3
Quote:
I painted the column today, so I didn't get around to making the lower mount as I'd promised in my first post. Maybe tomorrow. The plan is to do a plate/tube/bolt, something like this: |
|
![]() |
![]() |
![]() |
#611 |
Registered User
Join Date: Mar 2013
Location: albuquerque New Mexico
Posts: 522
|
Re: What did you do with your truck today, Part 3
fired it up and pulled it out of of the garage to make room for some garage projects. pulled it back in when I was done.
|
![]() |
![]() |
![]() |
#612 |
Account Suspended
Join Date: Aug 2016
Location: Florida, USA
Posts: 290
|
Re: What did you do with your truck today, Part 3
Well at least you got the fluids circulated. Try to park it in a slightly different location so your tires don't get flat-spotted from sitting.
|
![]() |
![]() |
![]() |
#613 |
Registered User
Join Date: Mar 2013
Location: albuquerque New Mexico
Posts: 522
|
Re: What did you do with your truck today, Part 3
my plan for this week is short. I need to move my fuel line away from the header and adjust the rear float. I'm dropping my dented front fender off at the shop today to be fixed.
|
![]() |
![]() |
![]() |
#614 |
Senior Member
![]() Join Date: Oct 2016
Location: Olympia, WA
Posts: 523
|
Re: What did you do with your truck today, Part 3
Getting ready to start my No Limit X-member kit!
|
![]() |
![]() |
![]() |
#615 |
Registered User
![]() Join Date: Apr 2016
Location: Temescal Valley, CA
Posts: 234
|
Re: What did you do with your truck today, Part 3
What manifold did you go with? I have block hugger headers and they interfere with the steering shaft.
|
![]() |
![]() |
![]() |
#616 | |
Registered User
Join Date: Sep 2014
Location: USA
Posts: 2,249
|
Re: What did you do with your truck today, Part 3
Quote:
Casting # 14007400 267-305-350 1980 Century, Grand Prix, LeMans 305 1980 Chevrolet passenger 267-305-350 1980 Malibu, Monte Carlo, Sprint 267-305 1980-81 Regal 305 1981 Camaro 267-305-350 1981 Chevrolet passenger, Malibu, Pontiac, Sprint 267-305 1981 Firebird 305 1981 LeMans 267 1982 Buick, Malibu, Monte Carlo, Olds, Pontiac, Regal, Sprint 267 1982 Chevrolet passenger 267-305 1982-86 Cutlass, Malibu, Monte Carlo, Pontiac, Regal, Sprint 305 1983-86 Grand Prix 305 Last edited by MiraclePieCo; 12-20-2017 at 10:30 PM. |
|
![]() |
![]() |
![]() |
#617 |
Registered User
Join Date: Mar 2013
Location: albuquerque New Mexico
Posts: 522
|
Re: What did you do with your truck today, Part 3
took my dented out of round fender to the shop. now I don't know if any of you have had to have any body work done on your trucks but no shop wants to touch old metal anymore. took forever to find a guy. the insurance estimated 6 hours work. I told them they were wrong. the body shop said 12hours. I called the assessor and had him call the shop directly. my brother is in town for the holidays and we are going to get into the garage and find out what my fuel issue is. hes a great mechanic and builder so I have high hopes. hes also my best friend and nothing is better then wrenching with a good friend.
|
![]() |
![]() |
![]() |
#618 |
Registered User
Join Date: Oct 2017
Location: Moorpark, California
Posts: 15
|
Re: What did you do with your truck today, Part 3
Cleaned out the all the dirt so i can soon install the wire harness and cleaned up the tach gauge.
|
![]() |
![]() |
![]() |
#619 |
Registered User
Join Date: Mar 2013
Location: albuquerque New Mexico
Posts: 522
|
Re: What did you do with your truck today, Part 3
my brother and I did get into the garage and made miracles happen. took about 20 minutes and my brother noticed that the truck started and idled great but as soon as it was warm had all kinds of fuel issues. went super lean. ive been saying that's what it did but couldn't figure it out. we tried to adjust the choke and it was STUCK! we had to use a flat blade screw driver to pop it off. once that was done we were able to get it right and it made a huge difference. then we rest all of the mixture screws and for kicks checked the timing. the timing seemed fine to me but he moved it a degree or two and wouldn't you know it made all the difference. my stumble is gone, my self adjusting float levels are gone, my STUMBLE is GONE! I have done all of the adjustments before but I would have never thought about this being a choke issue. I hadn't even considered it. we took the truck out for a quick drive and it was smooth as silk. we are gonna beat on it over the next couple of days to see if it requires any further adjustment. telling you guys there is nothing like wrenching with your best friend.
|
![]() |
![]() |
![]() |
#620 | |
Senior Member
![]() Join Date: Sep 2016
Location: Hershey, PA
Posts: 1,004
|
Re: What did you do with your truck today, Part 3
Quote:
![]()
__________________
Current Build Thread 1930 Ford Model A Modern Twist: Ford Model A Rat Rod With a Modern Twist Build Thread Phase 1 "The Swap": 1949 3100 with S10 swap. Beginner build with ambition! Build Thread Phase 2 "The Drop": Beginner Build with Ambition gets Air Ride |
|
![]() |
![]() |
![]() |
#621 |
Registered User
Join Date: Mar 2013
Location: albuquerque New Mexico
Posts: 522
|
Re: What did you do with your truck today, Part 3
|
![]() |
![]() |
![]() |
#622 |
Registered User
Join Date: Dec 2011
Location: Creighton Sask. Canada
Posts: 4,121
|
Re: What did you do with your truck today, Part 3
Tis the season for miracle's even for a truck.
![]() Mudman.
__________________
1987 Green n Green machine. 5.0 4spd std. 7" lift w 35's. |
![]() |
![]() |
![]() |
#623 |
Registered User
Join Date: Apr 2011
Location: Virginia Beach, VA
Posts: 505
|
Re: What did you do with your truck today, Part 3
Finally got my McGaughy's drop spindles on. Liking how it dropped it back down to sea level! Funny - I was lowering it off the jack stands and actually got the floor jack stuck under the crossmember. Luckily, Santa brought me a new low profile jack! Hope everyone had a great Christmas!
Cheers, Jim |
![]() |
![]() |
![]() |
#624 |
RUNNING OUT OF TIME
![]() Join Date: Jan 2010
Location: AMARILLO,TEXAS
Posts: 53
|
Re: What did you do with your truck today, Part 3
Looks good
__________________
1958 CHEVY SWBFLEETSIDE ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#625 |
Registered User
Join Date: Sep 2014
Location: USA
Posts: 2,249
|
Re: What did you do with your truck today, Part 3
I see you installed new lowering coils. It usually takes 100 miles or so for a set of new coils to settle, in my experience as much as 2-3 inches. Combined with the drop spindles, after driving your truck may end up lower than you want!
|
![]() |
![]() |
![]() |
Bookmarks |
|
|