68 aka "Chained in Porterbuilt Prison"

[69CST-V]

That looks very clean and factory like. Nice work.

[duallyjams]

Now I can see it, that's slic.

[superflysteiny]

looks great body work will be fun around the script.

[Hammered 77]

I like the small script,what is it off of?

[jtp67-72]

Originally Posted by Hammered 77

I like the small script,what is it off of?

Early Chevy small block valve cover....here's when i installed....And yes I stole this idea from a couple "unnamed" board members....lol....(HINT....ONE IS NOW NAMED MR. SEMA)........jim

[LODI3QTR]

Very Cool.....

[mcbassin]

Originally Posted by jtp67-72

Early Chevy small block valve cover....here's when i installed....And yes I stole this idea from a couple "unnamed" board members....lol....(HINT....ONE IS NOW NAMED MR. SEMA)........jim

Very cool! seems I remember seeing this on a glove box one time too.

[jtp67-72]

Originally Posted by superflysteiny

looks great body work will be fun around the script.

still got a little left...there is a slight long "bump" above the h-e-v-r that i have to address..was there from original ....no welding on this piece....it's so thin that this "distortion" was unseen until primer.....I'll get it though.....it's too neat to quit now.....Can u see what this would look like as a fender script?? So subtle and yet makes everyone go HUUUH??......Thinking i may cut the paint on the script back to bare metal after basing the entire gate...bonding clear over script..then clear whole gate...will give that "brushed " look.......jim

[67cheby]

love it, they should have done this from the factory..they had the stamps, why didnt they ask us ! LOL

[darkhorse970]

I thought that panel looked familiar. Very nice work!

[oldman3]

Hey Jim,love the panel piece and nice job on the clearance of last sill....Jim

[knomadd]

That's a pretty cool idea. I guessed the tailgate panel before I scrolled down, wasn't sure until I saw the cuts on the gate though. I like it!

[jtp67-72]

The weird thing is it was the exact width I needed and keep all the lines of the panel intact...usually doesn't work out...I don't have tools to make a panel like that ...so this was the alternative.....81-up Square body gate with handle welded up by the way...did welding and body work before cutting panel out...lot's easier and less chance of warpage...another cool thing is that all of the "cut" edges are hidden behind upper and lower sills except for ends which will square up nicely............jim

[67cheby]

looking great !

[jasonhall]

Very nice !! Lots of great ideas!

[72BlckButy]

I like it....

[mcbassin]

Very cool and original idea. I've never seen it before. Nice!

[Rusbuilt]

Great idea! Turned out awesome.

[jtp67-72]

Another feature that could be done with this is in the recess a trick gas cap could be mounted...I decided to use the side marker lite for 2 reasons..now that floor is raised the side marker is completely exposed on back side giving full "straight" access to tank bung...Also if u mounted the cap in the recess I think it would not be high enough for tank bung to fill properly....it's close and would work well if u left tank hanging down between frame rails but i'm having it made flush or near flush to bottom of rails...Yes another one of my "analism's".....can't take the tank hanging like it was an after thought!!

After lot of thought I'm leaning toward leaving the original tailgate handle...even bought the solenoids....but i'm leaving side markers,handles (although Camaro ),and putting trim back on.....truck is so low , handle (although ugly) shouldn't stand out ....well see....need to get moving on this project so less changes is better right now...Don't want to break the 7 year record of 67cheby!!............Mike u know I'm kidding!!!!!!

By the way ...look at the bottom edge of this tri-plus gate...that's not the camera .....it is that crooked....heavy metal for a repop but man...........

[67cheby]

mounts look great !

[jtp67-72]

Son of c10-n-stein...lol......thought i would take boards out...and let them "float"....4 bolts in bedside flange...tubs don't move.....grind in am.........jim

[jtp67-72]

Ok got over my illness.....back to the truck......got tubs nearly done..no pics yet .....but in between sandings....got some more little projects on bed in action..1st look at what front corner looks loke with stake pocket removed..fugly!!!! ....So i welded in pieces to smooth that out and cover the nutsert on front panel....just tacked in now ..will finish weld when i take it apart.....

[jtp67-72]

Then went to side marker lites and probably don't need to explain this except in last pic u can see how much easier gas filler will be since floor is raised completely above lite opening.....will do this on other side as well to have charging inserts for batteries....trick but been done by many before me!! For those looking close, i will have to move this "arm" inward some but I dont have the billet markers in my hand yet to check the thickness...Oh yeah Boyd tank coming...will have about 2-3" drop in hose from gas filler to tank fill opening ...should fill ok!......more later.......jim

[jtp67-72]

Well got a little done...tubs in guide coat ...epoxy in am followed shortly by high-build.....finished pass. side marker opener....thought u might want to see the hidden tub flanges...will be drilled for a few bolts when final wood is in place....and last built a "coffin" to send my cowl to Justin at his shop "SCOTT'S HOT RODS" in Calif..Never seen better metal work than they do....and I'm biting the bullet (not cheap) and letting them shave my cowl............jim

[jtp67-72]

And the others..........