What did you do to your truck today.The 3rd chapter - Page 26 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**70STOVEBOLT** · 06-07-2019, 10:11 AM

Quote:

Originally Posted by RodnRudy

I did the 500 mile break in oil and filter change today. I'm using NAPA 10/30 with Lucas Oil additive that has the zinc in it. Also replaced the coil in the HEI, I've been having problems with the engine not wanting to start after driving a while and getting good and warm. I've replaced two modules and no luck so I'm trying a different coil.

If you have an Edelbrock carb without an insulator gasket, the fuel is probably boiling out of the bowl. I had this problem with the stock cast iron intake until I put an insulator gasket between the intake and the spacer plate.

**RodnRudy** · 06-07-2019, 11:12 AM

Quote:

Originally Posted by 70STOVEBOLT

If you have an Edelbrock carb without an insulator gasket, the fuel is probably boiling out of the bowl. I had this problem with the stock cast iron intake until I put an insulator gasket between the intake and the spacer plate.

I've got a phenolic 1/2" spacer under the carb so I don't have a fuel boiling problem. When this happened I checked for spark and had none, and then when the engine cooled down some I'd get the spark back and it'd run. I did a test run yesterday with the replacement coil and it started right up even though the engine was hot. What irks me is that this is a new GM distributor but of course it has a made in Mexico sticker on it.

**70STOVEBOLT** · 06-07-2019, 12:41 PM

Quote:

Originally Posted by RodnRudy

I've got a phenolic 1/2" spacer under the carb so I don't have a fuel boiling problem. When this happened I checked for spark and had none, and then when the engine cooled down some I'd get the spark back and it'd run. I did a test run yesterday with the replacement coil and it started right up even though the engine was hot. What irks me is that this is a new GM distributor but of course it has a made in Mexico sticker on it.

Sounds like you are on the right track then. Hope the new coil solves the issue.

**Steeveedee** · 06-07-2019, 04:57 PM

Mexico doesn't have the same import requirements we do. A part can be imported from China to Mexico and then shipped to the US as "Made in Mexico".

Quikshft · 06-09-2019, 10:31 AM

Yesterday I added back most of the trim/bumpers etc after completing the paint job. Still have a lot of molding to put on to complete the two tone look.

**SoCoC10** · 06-09-2019, 11:50 AM

I think I might be done with this one. Nice distraction while the K5 was back at the paint shop. Wanted to make a mini version of my 71 C10 Cheyenne SWB. There's more pictures and details in the "Our Stuff in scale" area.

InNeedofaDelorean · 06-09-2019, 02:29 PM

Got dual exhaust put on, 2 inch pipe, 18 inch Cherry Bombs, and lucked into finding a set of slots from the cool dude I bought the truck from. Getting closer to that 70's look that I want.

NoStopN · 06-09-2019, 09:17 PM

I took mine down the road for a photo op.

tdangle · 06-09-2019, 09:52 PM

Upped the initial timing from 8 to 14 degrees to make total amount 36 degrees. Much better throttle response. Need to get a tach that goes to at least 4K rpm to see when total advance is all in. I'm thinking that I need to recurve the HEI distributor

weq92f · 06-11-2019, 12:38 PM

.
Pulled out the old dizzy and prepped the new one for install...

MSD 8361:

Stock blue bushing will stay there for 21* of mech timing.
Placed one light blue and one light silver spring on the mech assembly, this should bring all 21* of mech timing in just under 2500.

Will stab it in soon...

-klb

72c20customcamper · 06-11-2019, 05:16 PM

Since I can't paint my bed because my compressor went south. Can't complain its 27 years old . Motor is a GE 5 HP made in USA . Keeping that and the pump tank is shot. But I worked on the passenger door today. Inner door is all fixed and it fits very well little more body work and I'll paint it .

Picking up the new one tomorrow at Tractor supply. Getting the 80 gallon ingersal rand .

**WorkinLonghorn** · 06-11-2019, 06:40 PM

Changed the oil and filter replacing 10-30 with 10-40.

Replaced dimmer switch with ACDELCO D808 (Made in Taiwan-the first one i ordered didn't work).

Reconnected the wiper switch connector that has been off for 2 years now that the rain is done for the year and I won't need it.

This is fun, if it wasn't 96° out I'd do more. -BA

tdangle · 06-12-2019, 09:58 AM

Quote:

Originally Posted by WorkinLonghorn

Changed the oil and filter replacing 10-30 with 10-40.

Replaced dimmer switch with ACDELCO D808 (Made in Taiwan-the first one i ordered didn't work).

Reconnected the wiper switch connector that has been off for 2 years now that the rain is done for the year and I won't need it.

This is fun, if it wasn't 96° out I'd do more. -BA

It has been hot this week so far!!

**Steeveedee** · 06-12-2019, 12:46 PM

Yup summer finally hit. It's been really nice up to now. The AC ran for the first time yesterday. I'm hoping that that means we're going to have a cooler summer again.

Astro-Balls · 06-15-2019, 06:14 PM

Had the '68 Steam Cleaned today, took off about 100 lbs of dirt and grease..
Now i can see where all of the Zerk fittings are..

**ohboy321** · 06-15-2019, 06:16 PM

Painted some of the parts needed to put the engine bay back together, but the best part was getting a 67 steering wheel in the mail. My 67 currently has a 70 style, and I can't wait to put the correct one in. It was a good deal on a "buy it now" on the auction site, and the bonus was the nice horn button with no broken tabs that came with it. Plus it has all the internals to make it go beep! Will eventually restore it in black, but will install as-is to enjoy for now. Benny likes it...

Richard Jensen · 06-16-2019, 01:07 AM

Hello,
Replaced my after market, all aluminum radiator. Well out of warranty, but the rad shop owner checked for electrolysis but didn't see any and after discussing it with the maker, they decided to issue a new replacement!!!

Also checked/cleaned the ground from the battery to rad support and installed new air cleaner element. Tommorrow's plans include servicing the rest of the truck (oil, grease, filters) and checking all of the rest of the grounding straps. If time allows, rotating the tires. Rad shop was Best Radiators in Hays ks.

Chuck A · 06-16-2019, 09:37 AM

Changed out my starter and starting circuit due to a no start condition. When I came across this splice in the ignition wire, I knew I was doing the right thing. Yes, that is a common household wire nut.

Redneck Rydes · 06-16-2019, 03:13 PM

Now that was a mess

**3757chevy** · 06-17-2019, 11:38 PM

I test fit fit my bed wood Today in between thunder storms. And I marked their position for later. Still a ways off from done.

Andy4639 · 06-18-2019, 07:33 PM

Got home Saturday from the 2019 Hot Rod Power Tour. Washing the truck Sunday and noticed brake fluid between the master cylinder and booster.

Called and ordered it got it Monday and painted it and installed it today. Bleed everything and now have brakes again.

Astro-Balls · 06-20-2019, 10:15 PM

Started removing the two auxiliary tanks today to have them cleaned out if possible, I would like to save them.
Tanks have not been used in 20 years, we will see what they look like inside when they are removed...

**WorkinLonghorn** · 06-21-2019, 12:27 AM

Quote:

Originally Posted by Astro-Balls

Started removing the two auxiliary tanks today to have them cleaned out if possible, I would like to save them.
Tanks have not been used in 20 years, we will see what they look like inside when they are removed...

That is one of my next projects too. I just bought 10 feet of 3/8" fuel line to connect up the three tanks. I used to use all three but I can't remember why I disconnected the saddle tanks. I do remember that the passenger side one would clog the filter regularly so I used the driver side one. I'll be watching your progress, if you post here or start a thread.

72c20customcamper · 06-21-2019, 05:44 PM

Prepped the bed for the 68 for paint. Just need to hit it with 400 and spray it tomorrow. Did the steelies for the 72 came out nice. PPG single stage urethane they were definatly powder coated MEK didn't touch it bought them last year from road ready wheels. First picture is sanded. Second after two coats third after three and pretty much cured.

Astro-Balls · 06-21-2019, 08:11 PM

Got the Saddle tanks pulled today, Noticed a tear in each side of the bedside due to where they mounted the tank bracket to the lower wheel well.

06-07-2019, 04:57 PM	#629
Steeveedee Who Changed This? Join Date: Jan 2013 Location: Simi Valley, CA Posts: 10,614	Re: What did you do to your truck today.The 3rd chapter Mexico doesn't have the same import requirements we do. A part can be imported from China to Mexico and then shipped to the US as "Made in Mexico". __________________ ~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA

06-09-2019, 10:31 AM	#630
Quikshft Registered User Join Date: Oct 2010 Location: Kingsburg, Ca. Posts: 92	Re: What did you do to your truck today.The 3rd chapter Yesterday I added back most of the trim/bumpers etc after completing the paint job. Still have a lot of molding to put on to complete the two tone look. Attached Images

06-09-2019, 11:50 AM	#631
SoCoC10 Senior Member Join Date: Nov 2014 Location: Colorado Posts: 3,306	Re: What did you do to your truck today.The 3rd chapter I think I might be done with this one. Nice distraction while the K5 was back at the paint shop. Wanted to make a mini version of my 71 C10 Cheyenne SWB. There's more pictures and details in the "Our Stuff in scale" area. Attached Images __________________ 07' Extcab Silverado Z71 Silver Birch, 5.3L HO 71' Cheyenne C10 Hugger Orange on Saddle SWB Besides these two, too Many to count Last edited by SoCoC10; 06-09-2019 at 01:03 PM.

06-09-2019, 02:29 PM	#632
InNeedofaDelorean Registered User Join Date: Oct 2007 Location: Raytown, Missouri Posts: 130	Re: What did you do to your truck today.The 3rd chapter Got dual exhaust put on, 2 inch pipe, 18 inch Cherry Bombs, and lucked into finding a set of slots from the cool dude I bought the truck from. Getting closer to that 70's look that I want. __________________ 1972 GMC 3/4 2wd "Phantom"

06-09-2019, 09:17 PM	#633
NoStopN Registered User Join Date: Jul 2016 Location: Murfreesboro, TN Posts: 229	Re: What did you do to your truck today.The 3rd chapter I took mine down the road for a photo op. __________________ 1969 GMC 2500. 250 I6, 4-speed w/ granny low

06-09-2019, 09:52 PM	#634
tdangle Registered User Join Date: Mar 2005 Location: Jurupa Valley, Ca Posts: 1,210	Re: What did you do to your truck today.The 3rd chapter Upped the initial timing from 8 to 14 degrees to make total amount 36 degrees. Much better throttle response. Need to get a tach that goes to at least 4K rpm to see when total advance is all in. I'm thinking that I need to recurve the HEI distributor __________________ Terry 1970 Custom Camper/C20 , GM Crate 350/7004R, Dana 60, factory AC

06-11-2019, 12:38 PM	#635
weq92f Registered User Join Date: Oct 2016 Location: Dallas Texas Posts: 3,164	Re: What did you do to your truck today.The 3rd chapter . Pulled out the old dizzy and prepped the new one for install... MSD 8361: Stock blue bushing will stay there for 21* of mech timing. Placed one light blue and one light silver spring on the mech assembly, this should bring all 21* of mech timing in just under 2500. Will stab it in soon... -klb __________________ 67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi 07 335 sport turbo 6sp 94 Trans Am GT LT1 6sp posi -- sold after 22yrs 99 540 sport V8 6sp -- sold 73 240z L24 4sp -- given to friend 68 C10 step 350/350 3.73 open -- sold

06-11-2019, 05:16 PM	#636
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,650	Re: What did you do to your truck today.The 3rd chapter Since I can't paint my bed because my compressor went south. Can't complain its 27 years old . Motor is a GE 5 HP made in USA . Keeping that and the pump tank is shot. But I worked on the passenger door today. Inner door is all fixed and it fits very well little more body work and I'll paint it . Picking up the new one tomorrow at Tractor supply. Getting the 80 gallon ingersal rand . Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

06-11-2019, 06:40 PM	#637
WorkinLonghorn Senior Member Join Date: Dec 2006 Location: Studio City, Calif. Posts: 2,883	Re: What did you do to your truck today.The 3rd chapter Changed the oil and filter replacing 10-30 with 10-40. Replaced dimmer switch with ACDELCO D808 (Made in Taiwan-the first one i ordered didn't work). Reconnected the wiper switch connector that has been off for 2 years now that the rain is done for the year and I won't need it. This is fun, if it wasn't 96° out I'd do more. -BA __________________ '69 GMC C2500 Custom Camper, 8 1/2' bed, New GM 350, NP 435 Close Ratio 4spd. Trans., 3.73 Dana-60 open.Camper and Trailer wiring, PS, PB, AC, tach , three gas tanks, stereo speakers, 2nd owner, Work-Truck supreme. Last edited by WorkinLonghorn; 06-11-2019 at 06:54 PM.

06-12-2019, 12:46 PM	#639
Steeveedee Who Changed This? Join Date: Jan 2013 Location: Simi Valley, CA Posts: 10,614	Re: What did you do to your truck today.The 3rd chapter Yup summer finally hit. It's been really nice up to now. The AC ran for the first time yesterday. I'm hoping that that means we're going to have a cooler summer again. __________________ ~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA

06-15-2019, 06:14 PM	#640
Astro-Balls Registered User Join Date: Feb 2019 Location: Nor Cal Posts: 822	Re: What did you do to your truck today.The 3rd chapter Had the '68 Steam Cleaned today, took off about 100 lbs of dirt and grease.. Now i can see where all of the Zerk fittings are.. __________________ 1968 C20 Fleetside 396 4sp PS PB AC CST . https://www.youtube.com/watch?v=RWK8GgWD4uA

06-15-2019, 06:16 PM	#641
ohboy321 Senior Member Join Date: Aug 2015 Location: Dunbarton, NH Posts: 284	Re: What did you do to your truck today.The 3rd chapter Painted some of the parts needed to put the engine bay back together, but the best part was getting a 67 steering wheel in the mail. My 67 currently has a 70 style, and I can't wait to put the correct one in. It was a good deal on a "buy it now" on the auction site, and the bonus was the nice horn button with no broken tabs that came with it. Plus it has all the internals to make it go beep! Will eventually restore it in black, but will install as-is to enjoy for now. Benny likes it... Attached Images

06-16-2019, 01:07 AM	#642
Richard Jensen Registered User Join Date: Feb 2018 Location: LaCrosse Ks. Posts: 50	Re: What did you do to your truck today.The 3rd chapter Hello, Replaced my after market, all aluminum radiator. Well out of warranty, but the rad shop owner checked for electrolysis but didn't see any and after discussing it with the maker, they decided to issue a new replacement!!! Also checked/cleaned the ground from the battery to rad support and installed new air cleaner element. Tommorrow's plans include servicing the rest of the truck (oil, grease, filters) and checking all of the rest of the grounding straps. If time allows, rotating the tires. Rad shop was Best Radiators in Hays ks. __________________ Lead, follow, or get out of the way!

06-16-2019, 09:37 AM	#643
Chuck A Registered User Join Date: Aug 2018 Location: Columbus, Ohio Posts: 69	Re: What did you do to your truck today.The 3rd chapter Changed out my starter and starting circuit due to a no start condition. When I came across this splice in the ignition wire, I knew I was doing the right thing. Yes, that is a common household wire nut. Attached Images

06-16-2019, 03:13 PM	#644
Redneck Rydes Registered User Join Date: Feb 2016 Location: Trenton,Ontario & South Carolina Posts: 755	Re: What did you do to your truck today.The 3rd chapter Now that was a mess



Register or Log In To remove these advertisements.

06-17-2019, 11:38 PM	#645
3757chevy Senior Member Join Date: Mar 2016 Location: Near Canon City ,Colorado Posts: 4,033	Re: What did you do to your truck today.The 3rd chapter I test fit fit my bed wood Today in between thunder storms. And I marked their position for later. Still a ways off from done. Attached Images __________________ '35 1/2 ton Pickup (bought 2020) '68 C10 Suburban (bought 2021) '72 K5 Blazer (bought 2013) '67 Stepside (bought 1997-sold 2021) '96 Bronco Eddie Bauer (inherited 2010) My 1st day here-'67 C10(sold)and '72 K5 Blazer http://67-72chevytrucks.com/vboard/s...d.php?t=702056 "Another Blue Chevy"(1935) http://67-72chevytrucks.com/vboard/s...d.php?t=799203 '68 Burb...https://67-72chevytrucks.com/vboard/...d.php?t=822994 MIKE

06-18-2019, 07:33 PM	#646
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,945	Re: What did you do to your truck today.The 3rd chapter Got home Saturday from the 2019 Hot Rod Power Tour. Washing the truck Sunday and noticed brake fluid between the master cylinder and booster. Called and ordered it got it Monday and painted it and installed it today. Bleed everything and now have brakes again. Attached Images __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

06-20-2019, 10:15 PM	#647
Astro-Balls Registered User Join Date: Feb 2019 Location: Nor Cal Posts: 822	Re: What did you do to your truck today.The 3rd chapter Started removing the two auxiliary tanks today to have them cleaned out if possible, I would like to save them. Tanks have not been used in 20 years, we will see what they look like inside when they are removed... __________________ 1968 C20 Fleetside 396 4sp PS PB AC CST . https://www.youtube.com/watch?v=RWK8GgWD4uA

06-21-2019, 05:44 PM	#649
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,650	Re: What did you do to your truck today.The 3rd chapter Prepped the bed for the 68 for paint. Just need to hit it with 400 and spray it tomorrow. Did the steelies for the 72 came out nice. PPG single stage urethane they were definatly powder coated MEK didn't touch it bought them last year from road ready wheels. First picture is sanded. Second after two coats third after three and pretty much cured. Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

06-21-2019, 08:11 PM	#650
Astro-Balls Registered User Join Date: Feb 2019 Location: Nor Cal Posts: 822	Re: What did you do to your truck today.The 3rd chapter Got the Saddle tanks pulled today, Noticed a tear in each side of the bedside due to where they mounted the tank bracket to the lower wheel well. __________________ 1968 C20 Fleetside 396 4sp PS PB AC CST . https://www.youtube.com/watch?v=RWK8GgWD4uA

Register or Log In To remove these advertisements.