New 64 Stepper Project - Page 26 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**The Rocknrod** · 01-13-2022, 06:01 PM

Quote:

Originally Posted by aggie91

Your truck is just outstanding! and now you made improvements. Sure hope to get to see this one in person someday.

Me too.

Thanks for the positive comment.

I found out what was leaking. Once the timing cover is installed use THREEBOND 1217H sealant at the front of the timing cover lip, they are two piece and they are not sealed just spot welded so oil gets through.

SCOTI · 01-13-2022, 06:14 PM

Quote:

Originally Posted by The Rocknrod

Me too.

Thanks for the positive comment.

I found out what was leaking. Once the timing cover is installed use THREEBOND 1217H sealant at the front of the timing cover lip, they are two piece and they are not sealed just spot welded so oil gets through.

Leaks @ the seam huh?

Seems epoxy would be a more permanent solution for where the spot-weld seamed pieces meet vs relying on silicone/sealant solely. Always wondered about this area myself as it seems both front & rear of GM based oil pans are chronic leak prone.

**The Rocknrod** · 01-14-2022, 07:53 PM

Well she's back in the saddle again. Ran it for about 10 minutes. Still have to go get the exhaust hooked up.

**Joe Pass** · 01-14-2022, 11:28 PM

Nice..........

**The Rocknrod** · 01-15-2022, 11:37 AM

Thanks Joe.

Removed the rear end cover and letting it drain, maybe tomorrow I'll re-install it with "The Right Stuff" after I get it all clean.

SCOTI · 01-15-2022, 12:05 PM

Quote:

Originally Posted by The Rocknrod

Thanks Joe.

Removed the rear end cover and letting it drain, maybe tomorrow I'll re-install it with "The Right Stuff" after I get it all clean.

https://www.lubelocker.com/products/gm-12-bolt-llr-g012

Braunschweiger · 01-15-2022, 12:33 PM

What a great job, what a beauty, my greatest respect.
Greetings from Germany

**The Rocknrod** · 01-15-2022, 01:39 PM

Quote:

Originally Posted by SCOTI

https://www.lubelocker.com/products/gm-12-bolt-llr-g012

Thanks.
I actually have one of those.

Quote:

Originally Posted by Braunschweiger

What a great job, what a beauty, my greatest respect.
Greetings from Germany

Thank you for the positive comment.

**The Rocknrod** · 01-15-2022, 03:21 PM

So after snugging the bolts for the 12 bolt cover I used an inch pound torque wrench and started at 25 inch pounds. Per this post I then went to 45 inch pounds and it seems almost too tight. https://67-72chevytrucks.com/vboard/...51&postcount=2

SCOTI · 01-15-2022, 06:38 PM

Quote:

Originally Posted by The Rocknrod

So after snugging the bolts for the 12 bolt cover I used an inch pound torque wrench and started at 25 inch pounds. Per this post I then went to 45 inch pounds and it seems almost too tight. https://67-72chevytrucks.com/vboard/...51&postcount=2

I've never even looked up what the factory spec was. Always just snugged them up until I felt it was 'just enough'.

**The Rocknrod** · 01-15-2022, 07:41 PM

Quote:

Originally Posted by SCOTI

I've never even looked up what the factory spec was. Always just snugged them up until I felt it was 'just enough'.

I normally do the same. I was just trying something new

.

**The Rocknrod** · 01-27-2022, 04:56 PM

So I took it over to get the exhaust re-done due to the new manifolds at a local shop and on the rack.

**Joe Pass** · 01-27-2022, 08:30 PM

Did it work out?...I always fool with the exhaust, I'm never satisfied with the sound...

**The Rocknrod** · 01-27-2022, 08:33 PM

Quote:

Originally Posted by Joe Pass

Did it work out?...I always fool with the exhaust, I'm never satisfied with the sound...

I think it did, sounds just perfect for me. They really took theyre time on making sure it was run correctly. I'm happy with the work.

**clemdaddy** · 01-28-2022, 08:17 AM

Beautiful truck!
It's a good morning when you can have your coffee and read through a few pages of a great build thread. Thanks you Sir, and good morning to you.

Time to heat the shop...

**The Rocknrod** · 01-28-2022, 12:15 PM

Quote:

Originally Posted by clemdaddy

Beautiful truck!
It's a good morning when you can have your coffee and read through a few pages of a great build thread. Thanks you Sir, and good morning to you.

Time to heat the shop...

Thank you Clemdaddy, always good to hear from you.

**The Rocknrod** · 02-02-2022, 12:35 PM

I changed the jets and metering rods in my Street Demon to a tighter tolerance recently to get better mileage and my plugs showed signs of too fuel. I went two sizes smaller (not good).
Boy did I go too tight for my engine, I could hardly get down the street. I then put the smaller metering rod back in and was able to drive it, but it wanted to go into passing gear too much (looking for more fuel) when I sped up, I mean way more than normal. Plugs are now dry though

Now today I receive the next higher rods and jets, 2 main and 2 secondaries (and gaskets). Should be the ticket. Should have gone one size lower to begin with, live and learn I guess.
And wouldn't you know it. Got the parts, they sent One Jet in a package that was supposed to have two in a pack. They are sending me out a new set today.

**Joe Pass** · 02-02-2022, 04:00 PM

This is how to decide on the tune....trial and sometimes error...lol....
Every once in a while I make an adjustment or two...just to return back to my previous settings. It just to me confirms where you need to be....Good work

**The Rocknrod** · 02-02-2022, 04:03 PM

Quote:

Originally Posted by Joe Pass

This is how to decide on the tune....trial and sometimes error...lol....
Every once in a while I make an adjustment or two...just to return back to my previous settings. It just to me confirms where you need to be....Good work

Yes, with a carb like this metering rods and jets are all you have after you adjust vacuum, timing, idle. Takes time but I think I'll be happier doing it the hard way.

88Stanger · 02-08-2022, 04:36 PM

Damn Sir, that is one beautiful ride!!!! Great to see it on the road..

**The Rocknrod** · 02-08-2022, 07:05 PM

Thanks, still waiting on a couple parts due to the local freeze UPS said there was a delay.

88Stanger · 02-10-2022, 04:36 PM

Quote:

Originally Posted by The Rocknrod

Thanks, still waiting on a couple parts due to the local freeze UPS said there was a delay.

Figures.... Got to love UPS..... lol

**The Rocknrod** · 02-20-2022, 01:10 PM

I think I finally got that carb nailed down. Kept the 78's Jets and put in the 60-52 rods and she doesn't kick down when I get on the road all the time. Only when I make it kick down. I have to wait a while to report my mileage as right now it seems embarrassingly high.

Paul Y · 02-20-2022, 02:46 PM

Mr Rod,

You have excelled yourself with this truck.

The stance, has been nailed.

Love it.

P.

**The Rocknrod** · 02-20-2022, 03:52 PM

Quote:

Originally Posted by Paul Y

Mr Rod,

You have excelled yourself with this truck.

The stance, has been nailed.

Love it.

P.

Thank you Paul, of course being my worst critic I questioned that for a while.

01-14-2022, 07:53 PM	#628
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: New 64 Stepper Project Well she's back in the saddle again. Ran it for about 10 minutes. Still have to go get the exhaust hooked up. Attached Images __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

01-14-2022, 11:28 PM	#629
Joe Pass Senior Member Join Date: Aug 2013 Location: Windsor, California Posts: 1,042	Re: New 64 Stepper Project Nice.......... __________________ 1962 build album http://67-72chevytrucks.com/vboard/a...p?albumid=2066 http://67-72chevytrucks.com/vboard/a...p?albumid=2066 http://67-72chevytrucks.com/vboard/a...p?albumid=2067 1956 http://67-72chevytrucks.com/vboard/a...p?albumid=2086

01-15-2022, 11:37 AM	#630
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: New 64 Stepper Project Thanks Joe. Removed the rear end cover and letting it drain, maybe tomorrow I'll re-install it with "The Right Stuff" after I get it all clean. __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

01-15-2022, 12:33 PM	#632
Braunschweiger Registered User Join Date: Aug 2020 Location: Braunschweig, Lower Saxony, Germany Posts: 814	Re: New 64 Stepper Project What a great job, what a beauty, my greatest respect. Greetings from Germany

01-15-2022, 03:21 PM	#634
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: New 64 Stepper Project So after snugging the bolts for the 12 bolt cover I used an inch pound torque wrench and started at 25 inch pounds. Per this post I then went to 45 inch pounds and it seems almost too tight. https://67-72chevytrucks.com/vboard/...51&postcount=2 __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

01-27-2022, 04:56 PM	#637
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: New 64 Stepper Project So I took it over to get the exhaust re-done due to the new manifolds at a local shop and on the rack. Attached Images __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

01-27-2022, 08:30 PM	#638
Joe Pass Senior Member Join Date: Aug 2013 Location: Windsor, California Posts: 1,042	Re: New 64 Stepper Project Did it work out?...I always fool with the exhaust, I'm never satisfied with the sound... __________________ 1962 build album http://67-72chevytrucks.com/vboard/a...p?albumid=2066 http://67-72chevytrucks.com/vboard/a...p?albumid=2066 http://67-72chevytrucks.com/vboard/a...p?albumid=2067 1956 http://67-72chevytrucks.com/vboard/a...p?albumid=2086

01-28-2022, 08:17 AM	#640
clemdaddy Senior Member Join Date: Oct 2009 Location: Fayetteville, Arkansas Posts: 1,923	Re: New 64 Stepper Project Beautiful truck! It's a good morning when you can have your coffee and read through a few pages of a great build thread. Thanks you Sir, and good morning to you. Time to heat the shop...

02-02-2022, 12:35 PM	#642
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: New 64 Stepper Project I changed the jets and metering rods in my Street Demon to a tighter tolerance recently to get better mileage and my plugs showed signs of too fuel. I went two sizes smaller (not good). Boy did I go too tight for my engine, I could hardly get down the street. I then put the smaller metering rod back in and was able to drive it, but it wanted to go into passing gear too much (looking for more fuel) when I sped up, I mean way more than normal. Plugs are now dry though Now today I receive the next higher rods and jets, 2 main and 2 secondaries (and gaskets). Should be the ticket. Should have gone one size lower to begin with, live and learn I guess. And wouldn't you know it. Got the parts, they sent One Jet in a package that was supposed to have two in a pack. They are sending me out a new set today. Attached Images __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats? Last edited by The Rocknrod; 02-02-2022 at 01:36 PM.

02-02-2022, 04:00 PM	#643
Joe Pass Senior Member Join Date: Aug 2013 Location: Windsor, California Posts: 1,042	Re: New 64 Stepper Project This is how to decide on the tune....trial and sometimes error...lol.... Every once in a while I make an adjustment or two...just to return back to my previous settings. It just to me confirms where you need to be....Good work __________________ 1962 build album http://67-72chevytrucks.com/vboard/a...p?albumid=2066 http://67-72chevytrucks.com/vboard/a...p?albumid=2066 http://67-72chevytrucks.com/vboard/a...p?albumid=2067 1956 http://67-72chevytrucks.com/vboard/a...p?albumid=2086

02-08-2022, 04:36 PM	#645
88Stanger Registered User Join Date: Mar 2015 Location: Washington State Posts: 1,654	Re: New 64 Stepper Project Damn Sir, that is one beautiful ride!!!! Great to see it on the road.. __________________ John 3:16 - Saved me... God Bless

02-08-2022, 07:05 PM	#646
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: New 64 Stepper Project Thanks, still waiting on a couple parts due to the local freeze UPS said there was a delay. __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

02-20-2022, 01:10 PM	#648
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: New 64 Stepper Project I think I finally got that carb nailed down. Kept the 78's Jets and put in the 60-52 rods and she doesn't kick down when I get on the road all the time. Only when I make it kick down. I have to wait a while to report my mileage as right now it seems embarrassingly high. __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

02-20-2022, 02:46 PM	#649
Paul Y Registered User Join Date: Jul 2013 Location: Essex Posts: 950	Re: New 64 Stepper Project Mr Rod, You have excelled yourself with this truck. The stance, has been nailed. Love it. P. __________________ Woody's Build - http://67-72chevytrucks.com/vboard/s...d.php?t=658621 If it goes wrong, I blame the Internet...



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.