What did you do to your truck today? Chapter II - Page 275 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Redneck Rydes · 06-13-2018, 11:11 AM

Quote:

Originally Posted by Metaldoc

How about some smoked pickled eggs, I also made another 10 lbs of jerky. I have a fishing weekend coming up.

Does that fishing weekend involve a trip to The Bay Of Quinte?

BRL · 06-15-2018, 05:41 AM

Created twice the potential fuel & transmission leaks as I had before I started!

Apparently got to the old rubber fuel line just before it turned back into dust!

...can you imagine a rubber fuel line letting go, and coating the entire engine compartment with raw fuel, while you're buzzing down the highway @ 60... right before something decides to light it off!

...blow yer dang hood off for starters, then it will burn your poor little truck to the ground.

Hopefully you got out alright.

Performed a backyard tube job, and now all I have to do is make sure the band clamps stay tight...and probably change several small pieces of 2" rubber hose...um, roughly once a year.

90% hand bent and 10% tube bender tool (can you tell?)... Hey Shuddup! it's working alright!

toolboxchev · 06-15-2018, 12:40 PM

Quote:

Originally Posted by BRL

Created twice the potential fuel & transmission leaks as I had before I started!

Apparently got to the old rubber fuel line just before it turned back into dust!

...can you imagine a rubber fuel line letting go, and coating the entire engine compartment with raw fuel, while you're buzzing down the highway @ 60... right before something decides to light it off!

...blow yer dang hood off for starters, then it will burn your poor little truck to the ground.

Hopefully you got out alright.

Performed a backyard tube job, and now all I have to do is make sure the band clamps stay tight...and probably change several small pieces of 2" rubber hose...um, roughly once a year.

90% hand bent and 10% tube bender tool (can you tell?)... Hey Shuddup! it's working alright!

Do I see toolboxes mounted under the hood or what!

Metaldoc · 06-15-2018, 03:32 PM

Quote:

Originally Posted by Redneck Rydes

Does that fishing weekend involve a trip to The Bay Of Quinte?

Not this time, I'm up above Havelock at Lost lake, bass hunting. I raising the bar again with 10 hour smoked pulled pork for that trip as well. Bad news on my engine as the crank needs to be ground. So with all the new parts and machining I'm over 1000 bucks again for round two. smoked food heals all wounds.

88gtstreetrod · 06-15-2018, 05:49 PM

Removed the 20x9 fronts and put 18x8 on to try to give it some more rake...

Mudflat · 06-15-2018, 05:56 PM

Care to share how to make those eggs?

Metaldoc · 06-15-2018, 06:15 PM

Quote:

Originally Posted by Mudflat

Care to share how to make those eggs?

boil, cool, and peel eggs. Do not poke or break the white parts, no yokes showing. Warmed my smoker to 80 F ,cold smoke temp, started some apple, hickory, and mesquite chips. Turned off the heat and cold smoked the eggs for ten or so mins. 4 cups vinegar, 1 1/2 tbsp. brow sugar, 4 tbsp. pickling spice, 2 tbsp. sea salt. Bring to a boil and fill jarred eggs. I add a tsp of scotch bonnet hot sauce I make. Seal them up and I( spin the jars around once a day for 5 days at least but a week is better and enjoy.

BRL · 06-17-2018, 07:49 AM

Quote:

Originally Posted by toolboxchev

Do I see toolboxes mounted under the hood or what!

Yep, I have stereo amplifiers mounted under the bucket seats, so I put the tools and fluids etc. under the hood.

Been rather convenient all these years.

Jim Boy · 06-17-2018, 08:07 AM

Quote:

Originally Posted by Metaldoc

boil, cool, and peel eggs. Do not poke or break the white parts, no yokes showing. Warmed my smoker to 80 F ,cold smoke temp, started some apple, hickory, and mesquite chips. Turned off the heat and cold smoked the eggs for ten or so mins. 4 cups vinegar, 1 1/2 tbsp. brow sugar, 4 tbsp. pickling spice, 2 tbsp. sea salt. Bring to a boil and fill jarred eggs. I add a tsp of scotch bonnet hot sauce I make. Seal them up and I( spin the jars around once a day for 5 days at least but a week is better and enjoy.

I think it would be easier to go over to your place and just chow down. I mean you have already done the work eh. If we out here made the stuff and it didn't turn out right, your recipes would get a bad rap and that wouldn't be fair now would it. Just a lovely thought. Happy father's day. Let someone else do the BBQING today. Have a good one.

weq92f · 06-17-2018, 12:18 PM

Stabbed the cam!

Metaldoc · 06-17-2018, 12:32 PM

Quote:

Originally Posted by weq92f

Stabbed the cam!

Roller tip cam?

**3757chevy** · 06-17-2018, 01:00 PM

Quote:

Originally Posted by weq92f

Stabbed the cam!

Must be putting that in your '67? http://www.compcams.com/11-422-8.camshaft

weq92f · 06-17-2018, 04:20 PM

It's a roller! Going into the '67 along with a few other goodies.

http://67-72chevytrucks.com/vboard/s...d.php?t=755086

-klb

rjs53 · 06-17-2018, 09:05 PM

Finished plumbing the rear brake line from shortening the frame. Then replaced the cab mount bushings and bolted the bed back together. Was worried what it might look like or if it would line up, but everything worked out. Next is making access to the fuel tank now mounted in the back of the frame.

NoStopN · 06-17-2018, 11:37 PM

I finished tearing my replacement bed down. After that, I cut the bolts that hold my flatbed to the frame. I would have removed it but I didn't have anything strong enough to hang from the garage roof to remove it.

BruceKoukalaka · 06-18-2018, 11:06 PM

Just got it home, it was given to me for helping clean up a hoarder's home. It sat for 5 years (at least that's the last time it was plated).

rjs53 · 06-18-2018, 11:53 PM

Quote:

Originally Posted by BruceKoukalaka

Just got it home, it was given to me for helping clean up a hoarder's home. It sat for 5 years (at least that's the last time it was plated).

Lets see it

**3757chevy** · 06-19-2018, 12:00 AM

Quote:

Originally Posted by rjs53

Lets see it

VWNate1 · 06-19-2018, 12:02 AM

Pictures or it didn't happen !

.

**Already Gone** · 06-19-2018, 12:51 AM

Picked this up for my Highlander..

weq92f · 06-19-2018, 04:15 PM

Needed a dent in my front cover about a quarter of an inch deep right in the center where the cam sprocket button is. Took a measured swing or 3 with a BFH and an impact socket. Got quarter inch and a fraction more...so I had to beat on the inside of it too!

-klb

BruceKoukalaka · 06-19-2018, 05:22 PM

Here are the pics of my truck, it is a '69.

Metaldoc · 06-19-2018, 05:33 PM

Quote:

Originally Posted by weq92f

Needed a dent in my front cover about a quarter of an inch deep right in the center where the cam sprocket button is. Took a measured swing or 3 with a BFH and an impact socket. Got quarter inch and a fraction more...so I had to beat on the inside of it too!

-klb

Still clear the water pump?

**Steeveedee** · 06-19-2018, 06:17 PM

Sitting in line at the CostCo gas station yesterday, by the time I got to the pump the engine temp was about 210º (from 180º running on the road). Put a fan clutch on it today. Used the Hayden 2747 and gained about 1/2" more space from the radiator. The fan is at the front edge of the "tunnel", so we'll see how that works out. The new clutch is a lot heavier duty than what came off.

weq92f · 06-19-2018, 07:41 PM

Quote:

Originally Posted by Metaldoc

Still clear the water pump?

Haven't gotten that for yet! It should as it's the long pump and the cover is dented inward.

-klb

06-15-2018, 05:41 AM	#6852
BRL Registered User Join Date: Jun 2014 Location: Tahuya WA Posts: 608	Re: What did you do to your truck today? Chapter II Created twice the potential fuel & transmission leaks as I had before I started! Apparently got to the old rubber fuel line just before it turned back into dust! ...can you imagine a rubber fuel line letting go, and coating the entire engine compartment with raw fuel, while you're buzzing down the highway @ 60... right before something decides to light it off! ...blow yer dang hood off for starters, then it will burn your poor little truck to the ground. Hopefully you got out alright. Performed a backyard tube job, and now all I have to do is make sure the band clamps stay tight...and probably change several small pieces of 2" rubber hose...um, roughly once a year. 90% hand bent and 10% tube bender tool (can you tell?)... Hey Shuddup! it's working alright!

06-15-2018, 05:49 PM	#6855
88gtstreetrod Registered User Join Date: May 2018 Location: Atlanta, GA Posts: 45	Re: What did you do to your truck today? Chapter II Removed the 20x9 fronts and put 18x8 on to try to give it some more rake... Attached Images

06-15-2018, 05:56 PM	#6856
Mudflat Registered User Join Date: Mar 2018 Location: Spartanburg SC Posts: 48	Re: What did you do to your truck today? Chapter II Care to share how to make those eggs?

06-17-2018, 12:18 PM	#6860
weq92f Registered User Join Date: Oct 2016 Location: Dallas Texas Posts: 3,164	Re: What did you do to your truck today? Chapter II Stabbed the cam! Attached Images __________________ 67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi 07 335 sport turbo 6sp 94 Trans Am GT LT1 6sp posi -- sold after 22yrs 99 540 sport V8 6sp -- sold 73 240z L24 4sp -- given to friend 68 C10 step 350/350 3.73 open -- sold

06-17-2018, 04:20 PM	#6863
weq92f Registered User Join Date: Oct 2016 Location: Dallas Texas Posts: 3,164	Re: What did you do to your truck today? Chapter II It's a roller! Going into the '67 along with a few other goodies. http://67-72chevytrucks.com/vboard/s...d.php?t=755086 -klb Attached Images __________________ 67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi 07 335 sport turbo 6sp 94 Trans Am GT LT1 6sp posi -- sold after 22yrs 99 540 sport V8 6sp -- sold 73 240z L24 4sp -- given to friend 68 C10 step 350/350 3.73 open -- sold

06-17-2018, 09:05 PM	#6864
rjs53 Registered User Join Date: Jan 2010 Location: nevada Posts: 649	Re: What did you do to your truck today? Chapter II Finished plumbing the rear brake line from shortening the frame. Then replaced the cab mount bushings and bolted the bed back together. Was worried what it might look like or if it would line up, but everything worked out. Next is making access to the fuel tank now mounted in the back of the frame. __________________ 2003 Dodge 2500 1969 C10 2014 Camaro SS/RS/1LE

06-17-2018, 11:37 PM	#6865
NoStopN Registered User Join Date: Jul 2016 Location: Murfreesboro, TN Posts: 229	Re: What did you do to your truck today? Chapter II I finished tearing my replacement bed down. After that, I cut the bolts that hold my flatbed to the frame. I would have removed it but I didn't have anything strong enough to hang from the garage roof to remove it. __________________ 1969 GMC 2500. 250 I6, 4-speed w/ granny low

06-18-2018, 11:06 PM	#6866
BruceKoukalaka Registered User Join Date: Jun 2018 Location: De Winton Alberta Posts: 9	Re: What did you do to your truck today? Chapter II Just got it home, it was given to me for helping clean up a hoarder's home. It sat for 5 years (at least that's the last time it was plated).

06-19-2018, 12:02 AM	#6869
VWNate1 Registered User Join Date: Feb 2012 Location: So. Cali. Posts: 2,658	New Rig Pictures or it didn't happen ! . __________________ -Nate Geezer '49 3100 235 W/ Muncie SM420 SOLD '69 C/10 shortbed sidemount survivor 250 L6 W/ 350TH

06-19-2018, 12:51 AM	#6870
Already Gone 70+ ( Old Skool Club ) Join Date: Nov 2003 Location: Saskatoon, Saskatchewan ,Canada Posts: 9,141	Re: What did you do to your truck today? Chapter II Picked this up for my Highlander.. Attached Images __________________ 1972 C10 Custom/Deluxe 613 Highlander 406/700R4 1999 White Tahoe LS 4x2 with Z56 Police Package 1992 K1500 GMC Suburban Members I have personally met: MusicMan70 - HeavyD - ChewyChevy67 - StingRay -71SWB4x4 - 67 Burb - DeadheadNM - too much stuff - bc65 - das601 " Circumsatances Do Not Change Responsibility " " The Sky is not the Limit, Your Mind is." Marilyn Monroe .. RIP Charlie Watts 1941 - 2021

06-19-2018, 04:15 PM	#6871
weq92f Registered User Join Date: Oct 2016 Location: Dallas Texas Posts: 3,164	Re: What did you do to your truck today? Chapter II Needed a dent in my front cover about a quarter of an inch deep right in the center where the cam sprocket button is. Took a measured swing or 3 with a BFH and an impact socket. Got quarter inch and a fraction more...so I had to beat on the inside of it too! -klb Attached Images __________________ 67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi 07 335 sport turbo 6sp 94 Trans Am GT LT1 6sp posi -- sold after 22yrs 99 540 sport V8 6sp -- sold 73 240z L24 4sp -- given to friend 68 C10 step 350/350 3.73 open -- sold

06-19-2018, 05:22 PM	#6872
BruceKoukalaka Registered User Join Date: Jun 2018 Location: De Winton Alberta Posts: 9	Re: What did you do to your truck today? Chapter II Here are the pics of my truck, it is a '69. Last edited by BruceKoukalaka; 06-23-2018 at 02:24 PM.

06-19-2018, 06:17 PM	#6874
Steeveedee Who Changed This? Join Date: Jan 2013 Location: Simi Valley, CA Posts: 10,614	Re: What did you do to your truck today? Chapter II Sitting in line at the CostCo gas station yesterday, by the time I got to the pump the engine temp was about 210º (from 180º running on the road). Put a fan clutch on it today. Used the Hayden 2747 and gained about 1/2" more space from the radiator. The fan is at the front edge of the "tunnel", so we'll see how that works out. The new clutch is a lot heavier duty than what came off. __________________ ~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.