Project 67 DRGNWGN - 67 Burban!! - Page 29 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**kev2809** · 12-22-2020, 07:23 PM

Quote:

Originally Posted by Burb

Is the motor the only thing you pulling out of that donor?

its an 01? so it should be dbc. so im thinking at least motor trans pcm engine harness. not sure yet about anything else. what ya lookin for?

**kev2809** · 12-23-2020, 11:42 PM

quick question, i have everything unbolted and unplugged, ready to pull out....except the driveshaft. im having a huge mental lapse with pulling this driveshaft. is this the kind of ujoint that needs to be pressed out? i removed the clips but the damn u joint doesnt move at all.

**LockDoc** · 12-24-2020, 01:31 AM

Quote:

Originally Posted by kev2809

quick question, i have everything unbolted and unplugged, ready to pull out....except the driveshaft. im having a huge mental lapse with pulling this driveshaft. is this the kind of ujoint that needs to be pressed out? i removed the clips but the damn u joint doesnt move at all.

I can't remember what you have there. Does that shaft just pull out of the tail housing or does it have a nut on it? Do you have the other end of the shaft loose? You are probably not going to get that u-joint apart while it is still under the truck.

LockDoc

**kev2809** · 12-24-2020, 01:35 AM

Quote:

Originally Posted by LockDoc

I can't remember what you have there. Does that shaft just pull out of the tail housing or does it have a nut on it? Do you have the other end of the shaft loose? You are probably not going to get that u-joint apart while it is still under the truck.

LockDoc

ill check in the AM but i believe it slips out, i dont remember seeing a nut. and nope, other end is still intact

**LockDoc** · 12-24-2020, 01:38 AM

Quote:

Originally Posted by kev2809

ill check in the AM but i believe it slips out, i dont remember seeing a nut. and nope, other end is still intact

Then you will have to unbolt the other end and unbolt the carrier bearing bracket if it has one and pull the shaft out of the tail housing.

LockDoc

**kev2809** · 12-24-2020, 01:41 AM

Quote:

Originally Posted by LockDoc

Then you will have to unbolt the other end and unbolt the carrier bearing bracket if it has one and pull the shaft out of the tail housing.

LockDoc

ill have a look in the morning. i dont think ive ever pulled this driveshaft but i couldve sworn i had the trans out before

**kev2809** · 12-24-2020, 03:55 PM

Quote:

Originally Posted by LockDoc

Then you will have to unbolt the other end and unbolt the carrier bearing bracket if it has one and pull the shaft out of the tail housing.

LockDoc

guess that was the easiest way! i dont know why i was trying to avoid removing the driveshaft, it will need to come out anyways.

**LockDoc** · 12-25-2020, 02:11 AM

Quote:

Originally Posted by kev2809

guess that was the easiest way! i dont know why i was trying to avoid removing the driveshaft, it will need to come out anyways.

It really isn't too bad to remove them, just takes a little time.

LockDoc

**kev2809** · 12-26-2020, 01:09 PM

well, i feel like rewinded 5 years but it will be worth it in the end....plus i can do some things to the inner sides of these panels i should of done the 1st time.

used this tiny truck to pull the motor out

*edit* i dont know why these pics always turn out sideways

**kev2809** · 12-30-2020, 11:14 PM

found a knock off holley 302-2 pan kit for the motor. trying to stock pile some stuff together for now.

https://www.ebay.com/itm/402091342885

also, going with this 21 circuit rewire kit off amazon. basically a knock off of the EZ wire kit. i know, its not a big name brand, but im on a budget here and hope it works out

**LockDoc** · 12-31-2020, 11:08 AM

Quote:

Originally Posted by kev2809

found a knock off holley 302-2 pan kit for the motor. trying to stock pile some stuff together for now.

also, going with this 21 circuit rewire kit off amazon. basically a knock off of the EZ wire kit. i know, its not a big name brand, but im on a budget here and hope it works out

The wiring kit may be a little more work but it shouldn't be that hard to get sorted out if you have the old one to lay out and duplicate.

Let us know how it works out.

LockDoc

**kev2809** · 12-31-2020, 11:27 AM

Quote:

Originally Posted by LockDoc

The wiring kit may be a little more work but it shouldn't be that hard to get sorted out if you have the old one to lay out and duplicate.

Let us know how it works out.

LockDoc

oh, im sure ill be asking questions here lol. i plan to take pictures of everything i mount or attatch. not really a how to, but hey this is what i did kind of thing. ive been reading a lot on here about the ls swaps and wiring. i wont know what exactly ill be reusing off the old harness until i see what this one has. from the pictures it looks like it has a lot of our original plugs though

**kev2809** · 01-01-2021, 10:48 PM

just ordered these, hope they work out

Burb · 01-07-2021, 06:25 PM

Hey Kevin, were you running a York
motor mounted compressor for your suspension?

**kev2809** · 01-07-2021, 08:33 PM

Quote:

Originally Posted by Burb

Hey Kevin, were you running a York
motor mounted compressor for your suspension?

i had one on yes, with the small block. but i decided not to run it with the ls swap. i ran it a few times and it pumped super fast...but for some reason oil would spill out of the filter if i remember correctly. i think it might be in the build somewhere...i dont remember. its been about 4 or 5 years i think.

i still have it if ya want it, im gonna to start cleaning stuff up around here and trashing whatever doesnt sell. yard starting to look like sanford and son

Burb · 01-20-2021, 11:54 AM

Quote:

Originally Posted by kev2809

its an 01? so it should be dbc. so im thinking at least motor trans pcm engine harness. not sure yet about anything else. what ya lookin for?

LOL nothing out of an '01 , was just wondering.

Burb · 05-27-2021, 12:47 PM

Nudge ... Hey Kev

**kev2809** · 06-05-2021, 08:20 AM

Quote:

Originally Posted by Burb

Nudge ... Hey Kev

heyyyyy....

no updates yet, been putting a little money in my avalanche but about to get started on the suburban again soon hopefully. been doing some remodeling in my house also, floor guy is supposed to come this week. either way I have no choice to at least get my motor in by October, as the city now all of a sudden wants my neighborhood (non HOA by the way) to not have any "junk vehicles" unless they are behind a fence. soooo, had to spend 400 to make a fence around my suburban, and have until October to get rid of the donor vehicle.

**kev2809** · 09-21-2021, 09:00 PM

finally a little progress....somewhat. drove my donor truck in the driveway and started the teardown. I been picking at it since Sunday but I'm hoping to have the drive train out by next week. meanwhile, after pulling the intake... this motor looks filthy

**kev2809** · 09-26-2021, 09:41 PM

heeyyyyyy got my motor and trans out the donor and on the ground. went and bought my engine stand from northern tool today so hopefully will get it on the stand this week and start the teardown

**LockDoc** · 09-27-2021, 08:32 AM

-
Sounds good!

It all takes time, especially if you are still working. I started on a new project too and have had some interruptions. Just keep plugging away at it a little bit at a time and before you know it you will be driving it.

LockDoc

**kev2809** · 10-02-2021, 02:50 PM

huge setback with this motor...was draining the oil to get it on the stand and a ton of milkshake came out....kind of down to 2 options now. called my buddy where I got it from and he said he has another 2001 tahoe I could get. but I have to sell what I have and whatever I get would go to him for the other truck. other option would be to pull the heads and send them to get rebuilt and/or pressure tested for cracks or warps.

**LockDoc** · 10-02-2021, 07:58 PM

-
Well that sucks. Maybe it will be something simple like a gasket or "O" ring somewhere. I know that isn't really simple either but maybe you won't have to pull the whole thing....

LockDoc

**HO455** · 10-03-2021, 09:39 PM

Quote:

Originally Posted by kev2809

huge setback with this motor...was draining the oil to get it on the stand and a ton of milkshake came out....kind of down to 2 options now. called my buddy where I got it from and he said he has another 2001 tahoe I could get. but I have to sell what I have and whatever I get would go to him for the other truck. other option would be to pull the heads and send them to get rebuilt and/or pressure tested for cracks or warps.

UHGGGGGGG!!!! Man that just blows. .
Personally I would probably pull the heads and have them checked then I would know what kind of shape the cylinders are in. And of course I wouldn't be able to NOT pull the oil pan and inspect the oil pump. The evil demon "Project Creep" has arisen again.

**kev2809** · 10-03-2021, 10:11 PM

Quote:

Originally Posted by HO455

UHGGGGGGG!!!! Man that just blows. .
Personally I would probably pull the heads and have them checked then I would know what kind of shape the cylinders are in. And of course I wouldn't be able to NOT pull the oil pan and inspect the oil pump. The evil demon "Project Creep" has arisen again.

haha yup. well, I would've pulled the heads over the weekend but ima kind of see how the sale on it goes. if I didn't have the other truck as my other option I would dive deeper into this one.

I started of the frame clean up to keep me busy

12-23-2020, 11:42 PM	#702
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,172	Re: Project 67 DRGNWGN - 67 Burban!! quick question, i have everything unbolted and unplugged, ready to pull out....except the driveshaft. im having a huge mental lapse with pulling this driveshaft. is this the kind of ujoint that needs to be pressed out? i removed the clips but the damn u joint doesnt move at all. Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

12-26-2020, 01:09 PM	#709
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,172	Re: Project 67 DRGNWGN - 67 Burban!! well, i feel like rewinded 5 years but it will be worth it in the end....plus i can do some things to the inner sides of these panels i should of done the 1st time. used this tiny truck to pull the motor out edit i dont know why these pics always turn out sideways Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

12-30-2020, 11:14 PM	#710
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,172	Re: Project 67 DRGNWGN - 67 Burban!! found a knock off holley 302-2 pan kit for the motor. trying to stock pile some stuff together for now. https://www.ebay.com/itm/402091342885 also, going with this 21 circuit rewire kit off amazon. basically a knock off of the EZ wire kit. i know, its not a big name brand, but im on a budget here and hope it works out Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

01-01-2021, 10:48 PM	#713
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,172	Re: Project 67 DRGNWGN - 67 Burban!! just ordered these, hope they work out Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

01-07-2021, 06:25 PM	#714
Burb Coordinator of Synchronicity Join Date: Dec 2005 Location: West of Houston, TX Posts: 437	Re: Project 67 DRGNWGN - 67 Burban!! Hey Kevin, were you running a York motor mounted compressor for your suspension? __________________ Rick 1971 Suburban ... W.I.P. *Build Thread* Customization is ones personal touch-- not what other people think it should be

05-27-2021, 12:47 PM	#717
Burb Coordinator of Synchronicity Join Date: Dec 2005 Location: West of Houston, TX Posts: 437	Re: Project 67 DRGNWGN - 67 Burban!! Nudge ... Hey Kev __________________ Rick 1971 Suburban ... W.I.P. *Build Thread* Customization is ones personal touch-- not what other people think it should be

09-21-2021, 09:00 PM	#719
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,172	Re: Project 67 DRGNWGN - 67 Burban!! finally a little progress....somewhat. drove my donor truck in the driveway and started the teardown. I been picking at it since Sunday but I'm hoping to have the drive train out by next week. meanwhile, after pulling the intake... this motor looks filthy Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

09-26-2021, 09:41 PM	#720
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,172	Re: Project 67 DRGNWGN - 67 Burban!! heeyyyyyy got my motor and trans out the donor and on the ground. went and bought my engine stand from northern tool today so hopefully will get it on the stand this week and start the teardown Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

09-27-2021, 08:32 AM	#721
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,638	Re: Project 67 DRGNWGN - 67 Burban!! - Sounds good! It all takes time, especially if you are still working. I started on a new project too and have had some interruptions. Just keep plugging away at it a little bit at a time and before you know it you will be driving it. LockDoc __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

10-02-2021, 02:50 PM	#722
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 5,172	Re: Project 67 DRGNWGN - 67 Burban!! huge setback with this motor...was draining the oil to get it on the stand and a ton of milkshake came out....kind of down to 2 options now. called my buddy where I got it from and he said he has another 2001 tahoe I could get. but I have to sell what I have and whatever I get would go to him for the other truck. other option would be to pull the heads and send them to get rebuilt and/or pressure tested for cracks or warps. Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

10-02-2021, 07:58 PM	#723
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,638	Re: Project 67 DRGNWGN - 67 Burban!! - Well that sucks. Maybe it will be something simple like a gasket or "O" ring somewhere. I know that isn't really simple either but maybe you won't have to pull the whole thing.... LockDoc __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.