Jason's 70 Big Block SWB Project - Page 29 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BossHogg69 · 09-01-2016, 11:00 AM

Been a while since I checked in - all the details you've been working on/adding while waiting on the motor look nice! Good to hear you got the motor fired up with no issues. What cam are you running now? I'll keep my fingers crossed for you that the tranny goes in with no problems - you'll be washing vaporized rubber out of your rear wheelwells before long!

jeh · 09-01-2016, 08:45 PM

Quote:

Originally Posted by BossHogg69

Been a while since I checked in - all the details you've been working on/adding while waiting on the motor look nice! Good to hear you got the motor fired up with no issues. What cam are you running now? I'll keep my fingers crossed for you that the tranny goes in with no problems - you'll be washing vaporized rubber out of your rear wheelwells before long!

Thanks Adam, my buddy talked to Lunati with all the details of how my truck is set up, what I use it for and all the other details and they decided on the Lunati Voodoo roller cam part # 20110711LK, it has .575 lift. It's defiantly not as radical as it was before!!! As far as the rubber in the wheel wells, I should probably take it easy for a while this time and and let it break in

jeh · 09-15-2016, 12:13 PM

Things are about to happen around here!!!

**Vic1947** · 09-15-2016, 12:24 PM

That's a fine looking bullet and will look even better in between the frame rails! Almost time for those break-in butterflies.

jeh · 09-15-2016, 02:08 PM

Quote:

Originally Posted by Vic1947

That's a fine looking bullet and will look even better in between the frame rails! Almost time for those break-in butterflies.

I hope to have it settin between the frame rails by tomorrow. I have a little plumbing to finish up this evening on the new Wilwood master cylinder while I have room without the engine in. You're right about the butterflies, I sure hope everything is right this time

mud.man.rj · 09-15-2016, 11:11 PM

Ohh, the engine looks so nice, can't wait to hear it, must be excited.

jeh · 09-15-2016, 11:22 PM

Quote:

Originally Posted by mud.man.rj

Ohh, the engine looks so nice, can't wait to hear it, must be excited.

Thanks mudman, I am getting excited!!!
It's in and bolted up, I'm going to bed now. I'll start hooking the wiring up and double checking everything in the morning.

mud.man.rj · 09-15-2016, 11:25 PM

Sleep, I don't think so, will be building it all night.

jeh · 09-15-2016, 11:29 PM

Quote:

Originally Posted by mud.man.rj

Sleep, I don't think so, will be building it all night.

I know what your saying. I thought about pulling an all nighter so I could fire it up in the morning but I talked myself out of it. I'll just dream about it

mud.man.rj · 09-15-2016, 11:39 PM

Well one step closer and some time away helps all the other ideas and plans come to light, 427 SS, like the sound of that. Lucky guy.

Bennett68C10 · 09-16-2016, 08:19 AM

Looks great Jason, you'll be back on the road in no time.

mcbassin · 09-16-2016, 08:31 AM

Engine looks great Jason!

knomadd · 09-16-2016, 10:20 AM

Looks good in there!

jlsanborn · 09-16-2016, 12:03 PM

Super nice man! Please put up a video once you've got it running.

lyrikz · 09-16-2016, 06:37 PM

Quote:

Originally Posted by jeh

I had a pretty productive evening after I got home from work. I got the Fesler tail lights installed and the rear bumper brackets painted and put on

I know this is super old, but who makes those? Cost? Board member?

jeh · 09-17-2016, 06:53 PM

Quote:

Originally Posted by mcbassin

Engine looks great Jason!

Thanks Mike

Quote:

Originally Posted by knomadd

Looks good in there!

Thanks

Quote:

Originally Posted by jlsanborn

Super nice man! Please put up a video once you've got it running.

Thanks, I'll try to post a video??

Quote:

Originally Posted by lyrikz

I know this is super old, but who makes those? Cost? Board member?

I'll have to look through my receipts, he was a vendor on here.

Here's the aluminum fan shroud I made yesterday, this should make it run a little cooler than was before

jeh · 09-17-2016, 07:09 PM

Well now that I have "go" power, I have no"stop" power!!!!!
The only thing I changed on the brake system is the master cylinder and booster. It's a Wilwood m/c and today we bled brakes for 2 hours and I have nothing, pedal still goes to the floor.... Anybody have this issue before???

sduckworth13 · 09-17-2016, 07:53 PM

Nice work Jason! Sounds like you need to adjust the brake pedal rod a little that goes to master cylinder. Should be a easy fix.

**nlped** · 09-17-2016, 07:54 PM

^^^ The system is moving fluid but no brakes or no fluid moving through the system?

jeh · 09-17-2016, 09:16 PM

Quote:

Originally Posted by sduckworth13

Nice work Jason! Sounds like you need to adjust the brake pedal rod a little that goes to master cylinder. Should be a easy fix.

Thanks Scott, I'll take a look at that tommorrow, I took a break from it this evening. Thursday and Friday were some long days getting everything ready to put it back together....

Quote:

Originally Posted by nlped

^^^ The system is moving fluid but no brakes or no fluid moving through the system?

The system is moving some fluid but it don't seem like very much, we bled for about 2 hours and the pedal never got firm.

Jason7121 · 09-17-2016, 09:47 PM

Had a similar issue make sure bleeder screw on caliper is at top of caliper not bottom. My buddy did this and could never get a good pedal. He swapped calipers side to side and was corrected.

jeh · 09-17-2016, 09:57 PM

Quote:

Originally Posted by Jason7121

Had a similar issue make sure bleeder screw on caliper is at top of caliper not bottom. My buddy did this and could never get a good pedal. He swapped calipers side to side and was corrected.

The bleeders are on top, I checked that during the "head scratching" today. The thing is it worked fine till I changed the m/c and booster. The calipers and drums on the rear have not been messed with that's what I'm not understanding. Like Scott said above, if the rod is not pushing the piston in far enough that makes sense. It just don't seem like it squirts the fluid as hard as it should.

Jason7121 · 09-17-2016, 11:09 PM

Unbold master from booster and push on pedal see how far pedal moves before it makes contact with master cylinder piston.

jeh · 09-18-2016, 08:19 AM

Quote:

Originally Posted by Jason7121

Unbold master from booster and push on pedal see how far pedal moves before it makes contact with master cylinder piston.

Thanks, I'm going to check that today. That seems to make sense, the master and booster came disassembled so maybe the rod is not the right length.

**Vic1947** · 09-18-2016, 09:29 AM

Did you bleed the M/C first? If air is trapped in the pistons it can act like you describe.

09-01-2016, 11:00 AM	#701
BossHogg69 motor exploder Join Date: Mar 2009 Location: Pittsburgh, PA Posts: 2,346	Re: Jason's 70 Big Block SWB Project Been a while since I checked in - all the details you've been working on/adding while waiting on the motor look nice! Good to hear you got the motor fired up with no issues. What cam are you running now? I'll keep my fingers crossed for you that the tranny goes in with no problems - you'll be washing vaporized rubber out of your rear wheelwells before long! __________________ Adam 1969 Chevy CST/10 stepside, DART Big M/TREMEC Magnum Extreme/3.73's w/Detroit Truetrac 1965 Chevy Bel Air Wagon (daily driver), 327/TH350,10 bolt w/3.08's 1961 Chevy Bel Air Sport Coupe, ZZ454/M21/9" rear w/3.50's & Detroit Truetrac 2005 GMC 1500 ccsb 2wd, 6.0L/4L65e/3.73 G80 2006 GMC 2500HD ccsb 4x4, DMax LBZ/Allison 6spd/4.56's w/Detroit TrueTrac Use the SEARCH function on this forum - it is your friend!!

09-15-2016, 12:13 PM	#703
jeh Registered User Join Date: Jul 2011 Location: sutton WV Posts: 1,822	Re: Jason's 70 Big Block SWB Project Things are about to happen around here!!! Attached Images __________________ Jason '70 C-10 short fleet 427BB TH400 (SOLD) '10 Ford F 350 '13 Ford RAPTOR 6.2 MY BUILD THREAD http://www.67-72chevytrucks.com/vboa...d.php?t=612623

09-15-2016, 12:24 PM	#704
Vic1947 Senior Member Join Date: Mar 2012 Location: Kansas City, MO Posts: 2,054	Re: Jason's 70 Big Block SWB Project That's a fine looking bullet and will look even better in between the frame rails! Almost time for those break-in butterflies. __________________ Victor 57 Chevy Wagon - California Dreamin'"Mecum'd" 9/2022 Dallas, TX Crusty Rusty Leaky Squeaky 67 Consigned 4/2019 Dresden, Germany Maybelline - my '57 Ford 2dr Sedan "Mecum'd" 3/2016 Location unknown Silver Streaker "Mecum'd" 4/2013 Somewhere in Texas

09-15-2016, 11:11 PM	#706
mud.man.rj Registered User Join Date: Dec 2011 Location: Creighton Sask. Canada Posts: 4,121	Re: Jason's 70 Big Block SWB Project Ohh, the engine looks so nice, can't wait to hear it, must be excited. __________________ 1987 Green n Green machine. 5.0 4spd std. 7" lift w 35's.

09-15-2016, 11:25 PM	#708
mud.man.rj Registered User Join Date: Dec 2011 Location: Creighton Sask. Canada Posts: 4,121	Re: Jason's 70 Big Block SWB Project Sleep, I don't think so, will be building it all night. __________________ 1987 Green n Green machine. 5.0 4spd std. 7" lift w 35's.

09-15-2016, 11:39 PM	#710
mud.man.rj Registered User Join Date: Dec 2011 Location: Creighton Sask. Canada Posts: 4,121	Re: Jason's 70 Big Block SWB Project Well one step closer and some time away helps all the other ideas and plans come to light, 427 SS, like the sound of that. Lucky guy. __________________ 1987 Green n Green machine. 5.0 4spd std. 7" lift w 35's.

09-16-2016, 08:19 AM	#711
Bennett68C10 Registered User Join Date: Dec 2006 Location: Toms River, NJ Posts: 5,518	Re: Jason's 70 Big Block SWB Project Looks great Jason, you'll be back on the road in no time. __________________ Keith 66 Suburban Burb Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=751361 IG: bennett68c10

09-16-2016, 08:31 AM	#712
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: Jason's 70 Big Block SWB Project Engine looks great Jason! __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

09-16-2016, 10:20 AM	#713
knomadd Registered User Join Date: Jul 2012 Location: Rosenberg, Texas Posts: 3,506	Re: Jason's 70 Big Block SWB Project Looks good in there! __________________ -Duane C/10 Club Texas member 1971 Chevy C10 "Brutus" SWB Fleetside 2016 6.0L (L96) 6L90E (driver/project) 1965 Pontiac GTO "Royal Goat" 400/TH400 w/AC (my baby)

09-16-2016, 12:03 PM	#714
jlsanborn Registered User Join Date: Jun 2011 Location: Spokane, WA Posts: 2,372	Re: Jason's 70 Big Block SWB Project Super nice man! Please put up a video once you've got it running. __________________ '77 K30 3+3 - "The Crummy" http://67-72chevytrucks.com/vboard/s...d.php?t=640134 '67 C10 L/SWB - Soon to be daily driver! http://67-72chevytrucks.com/vboard/s...d.php?t=471776

09-17-2016, 07:09 PM	#717
jeh Registered User Join Date: Jul 2011 Location: sutton WV Posts: 1,822	Re: Jason's 70 Big Block SWB Project Well now that I have "go" power, I have no"stop" power!!!!! The only thing I changed on the brake system is the master cylinder and booster. It's a Wilwood m/c and today we bled brakes for 2 hours and I have nothing, pedal still goes to the floor.... Anybody have this issue before??? __________________ Jason '70 C-10 short fleet 427BB TH400 (SOLD) '10 Ford F 350 '13 Ford RAPTOR 6.2 MY BUILD THREAD http://www.67-72chevytrucks.com/vboa...d.php?t=612623

09-17-2016, 07:53 PM	#718
sduckworth13 Registered User Join Date: Mar 2011 Location: Kansas City, Missouri Posts: 3,541	Re: Jason's 70 Big Block SWB Project Nice work Jason! Sounds like you need to adjust the brake pedal rod a little that goes to master cylinder. Should be a easy fix. __________________ Scott

09-17-2016, 07:54 PM	#719
nlped Senior Member Join Date: Jul 2009 Location: Hayden, Al. Posts: 4,148	Re: Jason's 70 Big Block SWB Project ^^^ The system is moving fluid but no brakes or no fluid moving through the system? __________________ Carter 1968 Chevy SWB Fleet... Walt 1963-1/2 Ford Falcon Futura...Martha

09-17-2016, 09:47 PM	#721
Jason7121 Registered User Join Date: Jun 2016 Location: Visalia California Posts: 891	Re: Jason's 70 Big Block SWB Project Had a similar issue make sure bleeder screw on caliper is at top of caliper not bottom. My buddy did this and could never get a good pedal. He swapped calipers side to side and was corrected.

09-17-2016, 11:09 PM	#723
Jason7121 Registered User Join Date: Jun 2016 Location: Visalia California Posts: 891	Re: Jason's 70 Big Block SWB Project Unbold master from booster and push on pedal see how far pedal moves before it makes contact with master cylinder piston.



Register or Log In To remove these advertisements.

09-18-2016, 09:29 AM	#725
Vic1947 Senior Member Join Date: Mar 2012 Location: Kansas City, MO Posts: 2,054	Re: Jason's 70 Big Block SWB Project Did you bleed the M/C first? If air is trapped in the pistons it can act like you describe. __________________ Victor 57 Chevy Wagon - California Dreamin'"Mecum'd" 9/2022 Dallas, TX Crusty Rusty Leaky Squeaky 67 Consigned 4/2019 Dresden, Germany Maybelline - my '57 Ford 2dr Sedan "Mecum'd" 3/2016 Location unknown Silver Streaker "Mecum'd" 4/2013 Somewhere in Texas

Register or Log In To remove these advertisements.