My Daughter's 72 just made it home

[wreckedchevy]

appreciate the offer, it's the factory 307 and I have a spare factory oil line just need the adapter piece that screws into the block by the distributor.

[s_nova69]

I might have that. I will dig around

[wreckedchevy]

I think I just found an adapter for the oil line have to check it later to make sure

[Dean'smeanmachine]

nice project!

[wreckedchevy]

got the old cast iron intake off it, dang I forgot how heavy those are... got most the way threw cleaning up the heads hopefully have it cleaned up in the morning so when she gets home from work she can help me throw on that freebie intake and carb. the oil line adapter I found wasn't the right one so I'm still looking.

[wreckedchevy]

http://i1054.photobucket.com/albums/s486/wreckedchevy/Lizzys%202%20C10/20140805_131842_zpshqzg3x6u.jpg

Do any of you know what this wire is for ?
It's red heavy gauge wire I don't remember unhooking it doesn't look like it was hooked to anything for for long while now thanks

[wreckedchevy]

Nice my second was a bright orange 75 dodge colt followed by a brown 78 Fairmont high school was not kind to me.

I figured out the wire thanks anyhow

[wreckedchevy]

on a positive note we have gotten from here

to here

and here's where were at now

the battle I'm at right now is how to get all the eec vacuum lines hooked back up. any of you with an eec truck running edelbrock intake/carb have any input/pic's on how you hooked everything back up would be appreciated!!!!

[Dean'smeanmachine]

if im not mistaken that wire is the temperature gauge wire, which connects to the side of the engine (usually the drivers side) to the temperature thermostat

[Dean'smeanmachine]

it is below the exuast manifold,
hey we need a picture of your daughter with he truck

[wreckedchevy]

I figured out the wire it ran over to some kinda whoodamajigger that was attached to the stock 2 barrel. good luck on the pic I snuck a couple for momma and she was not amused with me :-)

[wreckedchevy]

forgot to mention it is alive once again definitely running better now that the 40 year old carb is off it. probably would have been simpler to just clean it but can't pass up freebie intake and carb!

[Bad Jackson]

Looks good! Lucky girl!

[wreckedchevy]

thanks, it's getting there right now were waiting on title (long story) and driver's side window regulator and then we will be able to finally take her for a spin.

[wreckedchevy]

after almost 2 month's we got the title work sorted out and plates on the truck so tomorrow we'll hopefully take it out for the first cruise!

[wreckedchevy]

test drive went pretty good been awhile since I drove anything without power steering. truck runs really well now and there is absolutely no noise coming from that old motor but once you get into the mid rpm's she start's to smoke like crazy. need to keep it moving some more and hopefully it will clean up.

yes I know world's smallest burnout but it was enough to scare the crap out of my girls

[In The Ten Ring]

Dude that's great. Now if I can just get mine going!

[wreckedchevy]

And now for the ugly... probably one of the rustiest cabs I've ran across around here I'm sure it's because the drilled a big hole in the roof for a cb antenna and didn't plug up any of the holes from the multiple different mirrors this poor truck has had. passenger side is the same except it also has some holes in the bottom of the door core and skin.

[wreckedchevy]

before we picked it up somebody hit the back of it with some farm equipment I didn't share earlier because I wanted to do the before/after thing but so far life's been getting in the way and we didn't get it finished yet. spent 1/2 day pulling on it but it's not coming out we are going to patch it instead.

[wreckedchevy]

we got it to the point we could install tail lights again and probably going to stay that way until after winter she won't have her license til the spring anyhow. the turn signals work but I the brake lights and tail lights don't work. soon as I get a chance I need to figure out what's going on with them any ideas? haven't looked into it yet at all.

[DeadheadNM]

Originally Posted by wreckedchevy

we got it to the point we could install tail lights again and probably going to stay that way until after winter she won't have her license til the spring anyhow. the turn signals work but I the brake lights and tail lights don't work. soon as I get a chance I need to figure out what's going on with them any ideas? haven't looked into it yet at all.

Great progress. Hurry - the snow is coming

Check all your grounds, bulbs, run the wires for breaks, and check the send unit thing at the brake pedal.

[wreckedchevy]

probably be better to keep this one to myself but I can't :-) the cab isn't very good and I already had everything but a piece of trim so I went ahead and made some room for the tunes

[Xeen]

Originally Posted by wreckedchevy

I went ahead and made some room for the tunes.

The purists are going to give you a hard time about that but in your defense it looks like you did a good job reshaping the hole, it isn't a hack job like we see most of the time.

[SCHRUMGMC]

What happened to that right bed fender?

[wreckedchevy]

It got clipped by some farm equipment he offered up a replacement bed side we are going to patch this one instead of replacing it