68 GMC 4x4 Suburban build up

[68SWB4x4]

Thanks guys I am looking forward to when it is done!

I am not looking forward to adding p/s to the flat 68 frame. If anyone has tips on the best way to dimple the frame I would appreciate it.

[68SWB4x4]

Been prepping the 87 1 ton to tear apart and pull the drivetrain and scrap the thing so I can get some more room.

Found some well used 315/75/16 (35) BFG Mud Terrains for 100 bucks so at least it will have the right size tires while its sitting around.

Going to have them mounted on some 16x8 steel rims off my old 95 gmc.

Also found this steering wheel in the dirt amongst some of my stuff. I cleaned it up last night. Even matches my interior!



Really wanting to get some work done on it but its been raining a ton here!

[Mr-Jack]

check this out about hydroboost brakes
http://coloradok5.com/forums/showthread.php?t=130488

[68SWB4x4]

Originally Posted by Mr-Jack

check this out about hydroboost brakes
http://coloradok5.com/forums/showthread.php?t=130488

Thanks for the link, very informative about hydroboost and further cements my desire to run it since I got all the parts already

Doesn't deal with retrofitting to a 67-72 though so still looking for that info if anyone has done it. I know some of you guys have!

[Mr-Jack]

i wouldn't imagine it being that much harder...might have to do a little sheet metal fab...trial and error might be the way to go here. maybe i'll work on it when i get into my brake system. If i do, i'll post it up, but that won't be for a while.

[68SWB4x4]

Originally Posted by Mr-Jack

i wouldn't imagine it being that much harder...might have to do a little sheet metal fab...trial and error might be the way to go here. maybe i'll work on it when i get into my brake system. If i do, i'll post it up, but that won't be for a while.

It should be fairly easy. I pulled the vacuum assist booster off today and will fab up the hydroboost later this week hopefully.

I also picked up these 16.5x8.25 slot mags today off craigslist for 150. Not going to use them right away but I always liked this style rim and they are hard to find in 8 lug so I jumped on the deal.

[Mr-Jack]

nice find...I style need to find some 3/4 ton running gear for my 67...maybe i'll just go tons on my blazer and put the 3/4 tons on my 67 hrmmm...make sure to keep us posted on the hydroboost install...i'd like to see how you went about it

[ERASER5]

FYI, 16.5 tires are getting hard to find. And expensive.

[68SWB4x4]

Originally Posted by ERASER5

FYI, 16.5 tires are getting hard to find. And expensive.

I will probably get some used 37" goodyear military tires.

[Mr-Jack]

not too bad...i'm runnign 16.5's on my 85 blazer and i have no problem getting the tires i use, but i'm runnin 40's so they're all gonna cost a little bit

[ERASER5]

I will cost me $750 to $1K before tax to get tires for mine. That is a little steep right now.

[Mr-Jack]

Originally Posted by ERASER5

I will cost me $750 to $1K before tax to get tires for mine. That is a little steep right now.

what kind of tires...i still haven't decided on what tires to go with. I don't want anything like Swampers/Boggers...i'll save those for my blazer (wheelin rig) but i never liked the look of All Terrains either, so i'm looking for something in the middle like an Goodyear MT/R or BFG KM2 or something like that, but i want them to last a couple of years. I also want to buy American made too, so it's a little limited in my choices, but not by far. I'll be going with 35's on 15" rims

[ERASER5]

$750 or so is for the Mastercraft (?)
$900 or so is for the BGF A/T and ProComp A/T
$1K or so is for the ProComp Mud
All D rated. All 33/16.5/12.50.

So for a moderate tire, it is a lot of coin for a guy out of work. I think I will search for used tires.

[Mr-Jack]

Kalle,

Got a couple of questions for ya...hope you're up for the challenge.

First i was gonna address the rearend of your burb. Looks like the shackle flip-n-switch went in nice, i see in your pictures tho that the tires don't appear to be centered in the wheel well



and i'm not sure if this has anything to do with the shackle angle, but is it just me or does it look too straight up and down



Are the stock rear springs centered on your burb?

Also what do your 52's measure from center pin to bolt hole on each side? cause it looks like your front is centered nicely from the picture i saw with the d60 under it and tires.

Thanks,

Jack

[68SWB4x4]

the shackle flip moves the tires forward about an inch I will address this when I swap the 14 bolt in the back. Kurt at DIY4X sold me a 1" block that has 3 different holes to move the axle back to line it up.

I'll measure my 52s I used in the front. They are stock springs off a 84ish gmc jimmy.

[Mr-Jack]

Originally Posted by 68SWB4x4

the shackle flip moves the tires forward about an inch I will address this when I swap the 14 bolt in the back. Kurt at DIY4X sold me a 1" block that has 3 different holes to move the axle back to line it up.

I'll measure my 52s I used in the front. They are stock springs off a 84ish gmc jimmy.

hrmm...well while you're out there can you measure the rears as well...i need to know if our truck springs are centered, and if you still have the stock fronts can you get those...i'll buy you a drink if we cross paths

[68SWB4x4]

Originally Posted by Mr-Jack

hrmm...well while you're out there can you measure the rears as well...i need to know if our truck springs are centered, and if you still have the stock fronts can you get those...i'll buy you a drink if we cross paths

I will probably be near my truck tomorrow if so I'll measure everything up. It would be good info to just have anyways.

[Mr-Jack]

thanks kalle..i appreciate it...here's a (really) crued drawing i whipped up in paint at work real quick of the dimensions i'm after for visual reference

i'm starting a thread about this for differant springs and such to do a spread sheet can you add the data to the thread in this link?
http://67-72chevytrucks.com/vboard/s...d.php?t=392551

Dimensions:
(Green) - D1:
(Blue) - D2:
(Brown) - D3:
(Purple) - D4:
(Yellow) - D5:
(Brown + Purple) - D6:

Front of the truck is on the left and this is for the front and rear

If you can get D1, D2, & D6 off the stock front i'd appreciate that too...

I'll do a write up on it and store it and post it for tech purposes and tag it that way future 67 & 68 owners can have this information

Thanks bro

[lowrollin70gmc]

Any updates on the suspension? I'm liking the shackle flip and b52s.

[68SWB4x4]

Originally Posted by lowrollin70gmc

Any updates on the suspension? I'm liking the shackle flip and b52s.

Thanks man, no updates yet sorry! I've been in the process of moving and bought another car for a driver which turned into a bigger project than I thought! But I plan to get back on it soon!

[70rs/ss]

Glad to see you are still giving it heck!! I bought that K30 and pulled the drivetrain about a week or two ago and will get the axles next. Anyone want a nice rust free 81 K30, come get it or it'll get crushed!! I am concerned about the front lift? I am sceeerd I'll need a ladder to get in it?! Looking good!!

[Mt Man Chad]

Looks like yours is almost a twin to my recently purchased 68 Chevy 4X4 burb.
Nice truck!

[68SWB4x4]

Originally Posted by Mt Man Chad

Looks like yours is almost a twin to my recently purchased 68 Chevy 4X4 burb.
Nice truck!

Sweet! Got any pics? TTT to keep me accountable.....

[68SWB4x4]

Life has been crazy busy with competing as a strongman, getting married, starting a business etc but I am going this afternoon to pick up my baby and bring her home from my moms ranch! Time to get serious

[68SWB4x4]

Got it loaded up and just about in the driveway... That might not seem like too big of a deal but it was parked on the side of a huge hill no brakes, no winch, giant burb... Got it done though! Feels good to have it home... Now to get the 454/th400/np205 over here and get this thing going...