1978 Russet Metallic 4x4 - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

K20chevy · 06-15-2016, 05:10 PM

Quote:

Originally Posted by buffydores

Opinion: What do y'all think about going with the 77 yellow stripe in the aluminum trim instead of the black? Seems like that might tie the interior to the exterior even better?

I think it would match very well. Mine is a 78 and i actually got the 77 trim for it because I like that even better. I'd say go for it if you can find the NOS parts. But you could just paint yours.

**buffydores** · 06-16-2016, 10:08 PM

Quote:

Originally Posted by K20chevy

I think it would match very well. Mine is a 78 and i actually got the 77 trim for it because I like that even better. I'd say go for it if you can find the NOS parts. But you could just paint yours.

I don't think the Blazer received the yellow trim, so I'd have to paint or vinyl stripe it. Probably vinyl stripe.

K20chevy · 06-17-2016, 08:51 AM

Quote:

Originally Posted by buffydores

I don't think the Blazer received the yellow trim, so I'd have to paint or vinyl stripe it. Probably vinyl stripe.

This should help you with the trim.

http://squarebodysyndicate.com/sbs-formula.html

Good luck with the 77 trim Transformation!

68Timber · 06-17-2016, 09:21 AM

Member tobytuttle used vinyl to stripe the trim on one of his trucks, link here: http://67-72chevytrucks.com/vboard/s...d.php?t=575608 It's on page one so no digging necessary.

On your front bumper, did you smooth the welds? It looks much better than most you see from the era.

**buffydores** · 06-17-2016, 09:20 PM

Quote:

Originally Posted by 68Timber

Member tobytuttle used vinyl to stripe the trim on one of his trucks, link here: http://67-72chevytrucks.com/vboard/s...d.php?t=575608 It's on page one so no digging necessary.

On your front bumper, did you smooth the welds? It looks much better than most you see from the era.

I certainly didn't smooth the welds, I was two years old, but Dad must have given the shop guys instructions to make it nice. So yes, all smooth.

Today we spent time servicing the winch. It's good now, but we need to touch up the bumper paint a bit on Monday.

I'm installing a new inverter on the passenger side, so I built a cute little 8 AWG harness with an inline fuse.

**buffydores** · 06-20-2016, 12:47 PM

Here's the new inverter installed.

**buffydores** · 06-20-2016, 03:42 PM

I cut the mats and trimmed to fit. I used a straight edge ruler and a box cutter. Took two or three passes to get through. This stuff is very heavy rubber.
I added an inch or so in places to increase the overall coverage of the mats.
The color match is remarkable. I am super pleased.
I forgot to take a photo, but I cut a matching piece to go in the bottom of the center console. As a child, I remember the never ending rattle of screw drivers and hammers in there. Wanted to address that.
I'll wash and detail the rubber before the reveal next Monday.

**buffydores** · 06-21-2016, 11:36 AM

Final two NOS pieces that need to go in. Those cruise control multi-function levers are rare birds (Part #6465256). It was a dealer installed option. The same part was used in Camaros. I upgraded the clock to the Quartz version in hopes that it will actually keep proper time.

Dc42d76 · 06-22-2016, 12:25 AM

Wow! Blazer turned out super sweet !!!! Didn't know you had a thread going on it. Just now stumbled on it. AWESOME job Cameron !! Keep those pics coming ! Everything looks great !!! Love those seats ! Woodgrain looks killer! That front bumper is so cool ! Paint looks great as well! The logo on the window is a very nice touch as well. Looking forward to seeing a pic with dad & the blazer.😀👍

*gmachinz* · 06-22-2016, 12:41 AM

Quote:

Originally Posted by buffydores

I don't think the Blazer received the yellow trim, so I'd have to paint or vinyl stripe it. Probably vinyl stripe.

They did-I know of a 77 Silverado equipped Blazer in a truck salvage yard still sporting some of the yellow 77-only trim....none of it is worth saving but it was cool to see. NOS Blazer stuff is hard to find...I don't have a lot of it myself.

**buffydores** · 06-22-2016, 04:32 AM

Quote:

Originally Posted by gmachinz

They did-I know of a 77 Silverado equipped Blazer in a truck salvage yard still sporting some of the yellow 77-only trim....none of it is worth saving but it was cool to see. NOS Blazer stuff is hard to find...I don't have a lot of it myself.

What?

I thought Cheyenne was the highest trim level for the Blazer in 1977. Either way, you could still have the yellow I guess. Don't know why they wouldn't.

**buffydores** · 06-22-2016, 04:33 AM

Quote:

Originally Posted by Dc42d76

Wow! Blazer turned out super sweet !!!! Didn't know you had a thread going on it. Just now stumbled on it. AWESOME job Cameron !! Keep those pics coming ! Everything looks great !!! Love those seats ! Woodgrain looks killer! That front bumper is so cool ! Paint looks great as well! The logo on the window is a very nice touch as well. Looking forward to seeing a pic with dad & the blazer.😀👍

Thanks Donny

**mrtoni** · 06-22-2016, 09:45 AM

I think Cheyenne was highest level trim higher than Silverado.

**buffydores** · 06-22-2016, 01:10 PM

Quote:

Originally Posted by mrtoni

I think Cheyenne was highest level trim higher than Silverado.

Really? Cool to know.

**buffydores** · 06-22-2016, 01:12 PM

Quote:

Originally Posted by Dc42d76

Wow! Blazer turned out super sweet !!!! Didn't know you had a thread going on it. Just now stumbled on it. AWESOME job Cameron !! Keep those pics coming ! Everything looks great !!! Love those seats ! Woodgrain looks killer! That front bumper is so cool ! Paint looks great as well! The logo on the window is a very nice touch as well. Looking forward to seeing a pic with dad & the blazer.😀👍

Just so everybody knows, Donny hooked me up with all the woodgrain stuff. He was great help. Thanks Donny again.

68Timber · 06-22-2016, 01:51 PM

Did you figure out the front-end clunk?

**buffydores** · 06-22-2016, 02:07 PM

Nope. I think it's something with the body.

**buffydores** · 06-23-2016, 01:54 PM

Looks like the adjustment rod hole for the clock is offset a bit from the '73-'80 dash. I'm ordering a '81-'87 instrument cluster plastic. I'll drill the '73-'80 plexi as a temporary solution. The clock works, which is nice.

**buffydores** · 06-23-2016, 05:31 PM

Got the front end dressed up. Hard to see, but the bumper was built with Hickey style hooks welded on the bottom. Kinda cool. Got the new stickers on the winch. New wheels are supposed to be delivered tomorrow. Detailing this weekend.

Here's a shot of the cross over steering and springs from Offroad Design:

**buffydores** · 06-27-2016, 03:17 PM

Wheels are in. I'm waiting on the chrome trim rings to finish it up.

68Timber · 06-27-2016, 03:22 PM

Are those narrower than stock? Don't get me wrong, they look great, but they look like they're not as wide or maybe the offset is different.

**buffydores** · 06-27-2016, 04:58 PM

16"x8" with 4.75" backspacing. Factory backspacing is 4.25". I've added 1" wheel spacers, so these are actually wider than factory by .5". Maybe it's the change from 15" to 16" that makes it look different.

**buffydores** · 06-27-2016, 05:08 PM

Forgot to post this little picture of the center console with the matching rubber bottom:

**buffydores** · 06-29-2016, 07:17 PM

Almost done. Still getting the clock, the fuel gauge sending unit and rear wheel spacers lined out. Then we're done. Just got all the rest ordered today. So probably the end of next week for all to be done.

1978 Cheyenne Big 10 · 06-30-2016, 07:17 PM

Hello!

Where were you able to locate the dark saddle color for the door panels to match the other door components and the dash too!?

You have an awesome truck!!

06-17-2016, 09:21 AM	#54
68Timber I know the pieces fit Join Date: Nov 2007 Location: MONTGOMERY, AL Posts: 5,523	Re: 1978 Russet Metallic 4x4 Member tobytuttle used vinyl to stripe the trim on one of his trucks, link here: http://67-72chevytrucks.com/vboard/s...d.php?t=575608 It's on page one so no digging necessary. On your front bumper, did you smooth the welds? It looks much better than most you see from the era. __________________ John 79 2wd Blazer (Bruiser) 85 M1009 Blazer (Sarge) build 74 Honda Z50 build

06-20-2016, 12:47 PM	#56
buffydores Senior Member Join Date: Mar 2016 Location: Longview, TX Posts: 758	Re: 1978 Russet Metallic 4x4 Here's the new inverter installed. Last edited by buffydores; 07-19-2017 at 03:31 PM.

06-20-2016, 03:42 PM	#57
buffydores Senior Member Join Date: Mar 2016 Location: Longview, TX Posts: 758	Re: 1978 Russet Metallic 4x4 I cut the mats and trimmed to fit. I used a straight edge ruler and a box cutter. Took two or three passes to get through. This stuff is very heavy rubber. I added an inch or so in places to increase the overall coverage of the mats. The color match is remarkable. I am super pleased. I forgot to take a photo, but I cut a matching piece to go in the bottom of the center console. As a child, I remember the never ending rattle of screw drivers and hammers in there. Wanted to address that. I'll wash and detail the rubber before the reveal next Monday. Last edited by buffydores; 07-19-2017 at 03:38 PM.

06-21-2016, 11:36 AM	#58
buffydores Senior Member Join Date: Mar 2016 Location: Longview, TX Posts: 758	Re: 1978 Russet Metallic 4x4 Final two NOS pieces that need to go in. Those cruise control multi-function levers are rare birds (Part #6465256). It was a dealer installed option. The same part was used in Camaros. I upgraded the clock to the Quartz version in hopes that it will actually keep proper time. Last edited by buffydores; 07-19-2017 at 03:39 PM.

06-22-2016, 12:25 AM	#59
Dc42d76 Registered User Join Date: Nov 2013 Location: Gallup, New Mexico Posts: 188	Re: 1978 Russet Metallic 4x4 Wow! Blazer turned out super sweet !!!! Didn't know you had a thread going on it. Just now stumbled on it. AWESOME job Cameron !! Keep those pics coming ! Everything looks great !!! Love those seats ! Woodgrain looks killer! That front bumper is so cool ! Paint looks great as well! The logo on the window is a very nice touch as well. Looking forward to seeing a pic with dad & the blazer.😀👍

06-22-2016, 09:45 AM	#63
mrtoni Senior Member Join Date: Jan 2009 Location: sparks, nevada Posts: 1,881	Re: 1978 Russet Metallic 4x4 I think Cheyenne was highest level trim higher than Silverado.

06-22-2016, 01:51 PM	#66
68Timber I know the pieces fit Join Date: Nov 2007 Location: MONTGOMERY, AL Posts: 5,523	Re: 1978 Russet Metallic 4x4 Did you figure out the front-end clunk? __________________ John 79 2wd Blazer (Bruiser) 85 M1009 Blazer (Sarge) build 74 Honda Z50 build

06-22-2016, 02:07 PM	#67
buffydores Senior Member Join Date: Mar 2016 Location: Longview, TX Posts: 758	Re: 1978 Russet Metallic 4x4 Nope. I think it's something with the body.

06-23-2016, 01:54 PM	#68
buffydores Senior Member Join Date: Mar 2016 Location: Longview, TX Posts: 758	Re: 1978 Russet Metallic 4x4 Looks like the adjustment rod hole for the clock is offset a bit from the '73-'80 dash. I'm ordering a '81-'87 instrument cluster plastic. I'll drill the '73-'80 plexi as a temporary solution. The clock works, which is nice.

06-23-2016, 05:31 PM	#69
buffydores Senior Member Join Date: Mar 2016 Location: Longview, TX Posts: 758	Re: 1978 Russet Metallic 4x4 Got the front end dressed up. Hard to see, but the bumper was built with Hickey style hooks welded on the bottom. Kinda cool. Got the new stickers on the winch. New wheels are supposed to be delivered tomorrow. Detailing this weekend. Here's a shot of the cross over steering and springs from Offroad Design: Last edited by buffydores; 07-19-2017 at 03:40 PM.

06-27-2016, 03:17 PM	#70
buffydores Senior Member Join Date: Mar 2016 Location: Longview, TX Posts: 758	Re: 1978 Russet Metallic 4x4 Wheels are in. I'm waiting on the chrome trim rings to finish it up. Last edited by buffydores; 07-19-2017 at 03:40 PM.

06-27-2016, 03:22 PM	#71
68Timber I know the pieces fit Join Date: Nov 2007 Location: MONTGOMERY, AL Posts: 5,523	Re: 1978 Russet Metallic 4x4 Are those narrower than stock? Don't get me wrong, they look great, but they look like they're not as wide or maybe the offset is different. __________________ John 79 2wd Blazer (Bruiser) 85 M1009 Blazer (Sarge) build 74 Honda Z50 build

06-27-2016, 04:58 PM	#72
buffydores Senior Member Join Date: Mar 2016 Location: Longview, TX Posts: 758	Re: 1978 Russet Metallic 4x4 16"x8" with 4.75" backspacing. Factory backspacing is 4.25". I've added 1" wheel spacers, so these are actually wider than factory by .5". Maybe it's the change from 15" to 16" that makes it look different.

06-27-2016, 05:08 PM	#73
buffydores Senior Member Join Date: Mar 2016 Location: Longview, TX Posts: 758	Re: 1978 Russet Metallic 4x4 Forgot to post this little picture of the center console with the matching rubber bottom: Last edited by buffydores; 07-19-2017 at 03:41 PM.

06-29-2016, 07:17 PM	#74
buffydores Senior Member Join Date: Mar 2016 Location: Longview, TX Posts: 758	Re: 1978 Russet Metallic 4x4 Almost done. Still getting the clock, the fuel gauge sending unit and rear wheel spacers lined out. Then we're done. Just got all the rest ordered today. So probably the end of next week for all to be done.



Register or Log In To remove these advertisements.

06-30-2016, 07:17 PM	#75
1978 Cheyenne Big 10 Registered User Join Date: Mar 2016 Location: Buford, GA Posts: 33	Re: 1978 Russet Metallic 4x4 Hello! Where were you able to locate the dark saddle color for the door panels to match the other door components and the dash too!? You have an awesome truck!!

Register or Log In To remove these advertisements.