Shrunken66Stroker's build thread.

[Reyals Bemus]

Is your transmission mounted at a rotated angle to the bellhousing? What's the reasoning?

Nice truck, awesome build!

[shrunken66stroker]

It's a Tremec World Class T-5 out of a 92 firebird. It's counter clocked 17 degrees toward the driver and it's got a short throw shifter for quick shifts. It's only rated to handle around 300 lb/ft of torque so it's perfect for my stock small block with a 4 barrel carb. If you're looking to put power down with slicks this is the wrong transmission. It's a good 5 speed with a .63x1 fifth gear ratio for cruising on the freeway. At 75 mph the the engine is just over 2000 rpms. At 85 mph it's still under 2500 rpm.

Originally Posted by Reyals Bemus

Is your transmission mounted at a rotated angle to the bellhousing? What's the reasoning?

Nice truck, awesome build!

[rayce08]

fbody trans

[Joey~AP]

Wow!

[jchav62]

Say Greg, is Tucker's still in business in Vegas? That's where I got a lot of parts for my trucks when I was still living out there. Maybe they'll have a lead on one of those grilles.

[shrunken66stroker]

Tucker's is still here. I go to them as much as I can. They're a little more expensive than LMC and others but they stock a lot of parts and know what they're talking about. That's a good idea, I'll give them a call and see. Thanks.

[jchav62]

Originally Posted by shrunken66stroker

Tucker's is still here. I go to them as much as I can. They're a little more expensive than LMC and others but they stock a lot of parts and know what they're talking about. That's a good idea, I'll give them a call and see. Thanks.

Yeah they are a bit pricier, but the convenience is great! I didn't mind paying a few bucks more and getting your parts the same day.

[Strodder]

Your doing a great job on your build. I know what you mean the build threads are a real inspiration to keep going.

[shrunken66stroker]

Thanks Strodder. Here are a few shots I took of how the whole thing is looking. I need to strip down the passenger door, the rest of the cab and the hood and it the whole thing will be bare naked.

[gostranger]

that is sick i love it i wish you were making it to lay the frame but i am sure it will be awesome!!!!!!!!!

[shrunken66stroker]

I'm building this truck to look stock on the outside(except for the rims) and have all of the modifications be on the inside. The bed floor is going to be raised up a few inches but will still appear stock from the outside. I kept the stake pockets on the bed rails, I didn't shave the door handles and I'm putting all of the trim back on. I notched the frame in the back but don't want to Z it and cut the bed up. 3 or 4 inches off the deck is close enough for me. I love looking at other peoples trucks laying frame though. Thanks for the compliments.

Originally Posted by gostranger

that is sick i love it i wish you were making it to lay the frame but i am sure it will be awesome!!!!!!!!!

[65VOL]

Looks awesome! I love the look of a bare panel after some quality sanding time.

[Strodder]

Hey Stroker, are you going to install 8 valves to control your Air Bags? It's a big advantage if you do.

[shrunken66stroker]

I don't have anything other than suspension parts and bags. No tank, compressor, valves or controller. I really have been concentrating on everything else. I need to research it more before I make a decision. I have temporary schrader valves on the lines and that should get me through till the rest of the build is done. Why 8 valves? Any other info is appreciated. Thanks.

Originally Posted by Strodder

Hey Stroker, are you going to install 8 valves to control your Air Bags? It's a big advantage if you do.

[Strodder]

I used to own Sportruck Specialties. I did many, many custom air bag jobs. Before you buy anything else for the air bags let me know first. I'll steer you straight. Or up & down.

[shrunken66stroker]

Thanks Strodder. It will be a while but I'll definitely be hitting you up for some more info. What do you think the price range is for a basic independent 4 corner system? I don't really care about the up and down speed. Everyone I've talked to says to get 4 corner adjustability. What do you think?

Originally Posted by Strodder

I used to own Sportruck Specialties. I did many, many custom air bag jobs. Before you buy anything else for the air bags let me know first. I can also get the parts for you at a good price. I'll steer you straight. Or up & down.

[Strodder]

Originally Posted by shrunken66stroker

Thanks Strodder. It will be a while but I'll definitely be hitting you up for some more info. What do you think the price range is for a basic independent 4 corner system? I don't really care about the up and down speed. Everyone I've talked to says to get 4 corner adjustability. What do you think?

The main reason to have 4 corner control is it will handle really good. You won't need a sway bar. When you have only front & rear controls, the air bag on the outside of a turn will have more pressure in it because of the weight transfer. So the air from that air bag will transfer to the other bag. With individual controls at each corner, that won't happen. It will reduce sway buy holding the pressure in those outside bags.
Prices are always changing with some of the components to make a kit. It can depend on how many compressor's you want, and what size air tank, lines, fittings, and switches. The minimum I would recommend would be 1/4" air lines, with 2 air compressor's, a air 5 gal tank, with 3/8" control valves. I would use brass fittings for reliability, and they will reduce leaking. Roughy I'm guessing you'll spend about $500.00 to $600.00. I'll check the exact price when your ready.

[shrunken66stroker]

I don't have anything other than suspension parts and bags. No tank, compressor, valves or controller. I really have been concentrating on everything else. I need to research it more before I make a decision. I have temporary schrader valves on the lines and that should get me through till the rest of the build is done. Any info is appreciated. Thanks.

Originally Posted by Strodder

Hey Stroker, are you going to install 8 valves to control your Air Bags? It's a big advantage if you do.

[shrunken66stroker]

Thanks 502. Here's last nights progress. I worked on the hood mainly, but I got a few other things done too. Basically I was out making a bunch of dust.

[protrash64]

Subscribed.......wanna keep up with the progress.

[jchav62]

Originally Posted by shrunken66stroker

Thanks 502. Here's last nights progress. I worked on the hood mainly, but I got a few other things done too. Basically I was out making a bunch of dust.

Nice!

[shrunken66stroker]

I'm going to have a gas tank in the back between the frame rails so I may have to tuck the tanks in front of the rear tire. Not sure yet. Thanks for the pics

[Strodder]

Originally Posted by shrunken66stroker

I'm going to have a gas tank in the back between the frame rails so I may have to tuck the tanks in front of the rear tire. Not sure yet. Thanks for the pics

I'm putting a Blazer tank in the back also. I checked and there is lots of room under the cab out side of the frame rails. You can put one 3 gal tank with 1 compressor on one side, and the same setup on the other side. It would be a clean set up, and look cool too.

[shrunken66stroker]

Do you have the blazer tank yet? If so, where did you get it and how much was it? I'm looking for one right now. Is it 21 gallon? What do you think about those fabbed up 19 gallon aluminum tanks? I know they're more expensive but they seem to tuck up nice between the rails. I don't want the tank to hang down and be visible.

Originally Posted by Strodder

I'm putting a Blazer tank in the back also. I checked and there is lots of room under the cab out side of the frame rails. You can put one 3 gal tank with 1 compressor on one side, and the same setup on the other side. It would be a clean set up, and look cool too.

[Strodder]

Originally Posted by shrunken66stroker

Do you have the blazer tank yet? If so, where did you get it and how much was it? I'm looking for one right now. Is it 21 gallon? What do you think about those fabbed up 19 gallon aluminum tanks? I know they're more expensive but they seem to tuck up nice between the rails. I don't want the tank to hang down and be visible.

Check my build thread. The tank cost me 50 bucks at a junk yard, but they punched a hole in it to drain the gas. The back half of my 65 has a 73 frame I put on it. The gas tank looks like it will fit good. I think it's a 22 gallon. I was going to get the tank from Truck Parts. It looked like a nice set up you bolt in. It's only $190.00 with sender and straps. Look at the index for gas tanks.
http://www.scribd.com/full/5722345?a...jcbazlklxtunnw