![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
Re: My new Beater 1959 GMC
Forgot to post this. Details! Semi blacked backside of cowl vent and cleaned up wiper trim. I am in AZ so no wipers is no problem.
__________________
I LOVE BURNOUTS ![]() ![]() NO BOZO's |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
Re: My new Beater 1959 GMC
The scuff and shoot continues.
__________________
I LOVE BURNOUTS ![]() ![]() NO BOZO's |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
Re: My new Beater 1959 GMC
More scuff and shoot.
__________________
I LOVE BURNOUTS ![]() ![]() NO BOZO's |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,026
|
Re: My new Beater 1959 GMC
do you plan to keep the 8 stud wheel running gear or upgrade to a smoother ride?
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
|
![]() |
![]() |
![]() |
#6 |
Senior Member
![]() Join Date: Aug 2010
Location: Shasta Lake, CA.
Posts: 1,619
|
Re: My new Beater 1959 GMC
That s-10 axle is too narrow for your truck . It will require tubs and reverse rims along with relocation of the springs .
A nova rear axle would work without much work .
__________________
Glen & Jane's Rides ‘57 GMC NAPCO Long Bed V8 4 speed Bought 2008 7 other cars & trucks , 5 trailers '56 Chevy Long Bed I6, 4 speed Bought 1990 Sold 8.22.2020 ’56 GMC Suburban Pickup V8, 4 speed Hydramatic Bought 1996 Sold 10.11.2020 My Other Tinkerings http://67-72chevytrucks.com/vboard/s...75#post8967275 |
![]() |
![]() |
![]() |
#7 |
Senior Member
![]() Join Date: May 2007
Location: Doodah Kansas
Posts: 7,773
|
Re: My new Beater 1959 GMC
love the transformation! i prefer the 55-7 front end too!
__________________
the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393 |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
Progress.
Posted via Mobile Device |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
Re: My new Beater 1959 GMC
Rear axle is a 3:42 rear ratio out of a 6 cyl s-10.
__________________
I LOVE BURNOUTS ![]() ![]() NO BOZO's |
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
Re: My new Beater 1959 GMC
Front end progress on the 59. These era trucks are real neat to play with, very simple how they all bolt together. 👍🏻👍🏻
__________________
I LOVE BURNOUTS ![]() ![]() NO BOZO's |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
Out of the box mustang 2 mock up dropped spindles and 5/8 narrowed A arms.
Posted via Mobile Device |
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,026
|
Re: My new Beater 1959 GMC
Nicely centered wheel. Check all the angles, tack, recheck before welding in. Digital level is really handy.
Antidive angle on top control arm pivot Lower control arm angles from front and side at ride height. What I do is extend the pivot shaft out through the front and place long level or straight edge between them, then digital torpedo level on top of that to ensure side to side on crossmember is level. Then torpedo level on one shaft at a time to get the fore to aft level. Then level the lower cross member side to side. Then check the upper control arm for side to side angle.a slight angle down to frame may be ok, up to you.it affects tire lean as suspension cycles. So tire doesnt hit fender. Anyway, it looks like you researched before starting. Keep posting up pics as you go. Maybe get some of us slackers off the couch. |
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Nov 2014
Location: somewhere, PA
Posts: 1,071
|
Re: My new Beater 1959 GMC
stretched ftw
|
![]() |
![]() |
![]() |
#14 |
Registered User
Join Date: Nov 2011
Location: Middle Georgia
Posts: 296
|
Re: My new Beater 1959 GMC
Those front engine mounts resemble what I had done in m '57 years ago.
|
![]() |
![]() |
![]() |
#15 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,026
|
Re: My new Beater 1959 GMC
what will the clearance be at the front of the rockers? hard to tell from the pics, but curious what rake angle you chose.
|
![]() |
![]() |
![]() |
#16 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
Posted via Mobile Device
|
![]() |
![]() |
![]() |
#17 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,026
|
Re: My new Beater 1959 GMC
last post was a blank screen.
|
![]() |
![]() |
![]() |
#18 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
Progress pics. Mock up motor and trans in finalizing location.
Posted via Mobile Device |
![]() |
![]() |
![]() |
#19 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
Can’t wait to do burnouts.
Posted via Mobile Device |
![]() |
![]() |
![]() |
#20 |
Registered User
Join Date: Nov 2011
Location: Middle Georgia
Posts: 296
|
Re: My new Beater 1959 GMC
It will be interesting to see how your headers fit with the IFS and tires/wheels. What kind are they? Don't think I have seen ones with that big of a bend radius in them. I like the concept if it will work!
|
![]() |
![]() |
![]() |
#21 |
Registered User
Join Date: Nov 2014
Location: somewhere, PA
Posts: 1,071
|
Re: My new Beater 1959 GMC
and we can't wait to see the vids!
|
![]() |
![]() |
![]() |
#22 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
Stock steering column mod. I like to run the stock steering wheel.
Wheel barrow bearing and shaft collar cost me $7.41 at the hardware store. Simple easy fix. Will shape end of steering shaft for Double D coupler. Posted via Mobile Device |
![]() |
![]() |
![]() |
#23 |
Registered User
Join Date: Jan 2013
Location: roseville
Posts: 823
|
Re: My new Beater 1959 GMC
Nice, that's a $40 problem usually.. who knew?!
__________________
My Current Trucks: 1958 Apache BBW 4.8LS/4l60 "Lucky" Built By Me 1958 GMC BBW LS1/4l60 "The Kraken" Built By Delmo |
![]() |
![]() |
![]() |
#24 |
Registered User
Join Date: Nov 2011
Location: Middle Georgia
Posts: 296
|
Re: My new Beater 1959 GMC
Oh my love the white headers!! What did you paint them with?
|
![]() |
![]() |
![]() |
#25 |
Registered User
Join Date: Sep 2007
Location: gilbert, az
Posts: 792
|
More FUN! Alignment is of but you get the idea.
Posted via Mobile Device |
![]() |
![]() |
![]() |
Bookmarks |
|
|