How to: Ruin a perfectly good C10 - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

CheyenneShop · 03-01-2011, 01:45 AM

nice work

VA72C10 · 03-01-2011, 02:00 AM

Nice! Love a clean undercarriage!!!

gringoloco · 03-01-2011, 10:31 PM

Painted the spindles, calipers, rotors, and other miscellaneous stuff. Had to get a shot of the brake dust shields since I have way more time than I care to share in cleaning them

Also lopped a full coil off of the brand new springs (cheaper than new drop springs) and got the driver's side assembled. I'll get it on the ground tomorrow and see if I need to trim the springs any more. Also had an upper control arm stud start spinning on me, so I need to do something about that before it goes out for alignment...

The before/after shot makes it all worth it

VA72C10 · 03-01-2011, 11:53 PM

Very nice work! Did you clear the cross shafts or paint them? What colors? Wanting to paint my suspension parts the correct colors....

gringoloco · 03-02-2011, 01:45 AM

Quote:

Originally Posted by VA72C10

Very nice work! Did you clear the cross shafts or paint them? What colors? Wanting to paint my suspension parts the correct colors....

I don't think clear would hold up on bare metal very well. Maybe try a cast iron grey- I'm sure Eastwood (or somewhere cheaper) has some. Colors I used were rust encapsulator black, chassis black, caliper black(on the spindles), and a grey caliper paint.

gringoloco · 03-03-2011, 12:51 AM

Got the suspension reassembled and put her back on the ground. Forgot just how low she actually sits when not on jackstands

I ended up using the Belltech drop coils that were previously installed since I couldn't get the Moogs to seat properly??? I dunno- the Belltechs dropped right in. Still need to do a little more clearancing on the LCAs; since I'm running van rallies with 3" drop spindles, they rub the wheels when turning sharply.

Once it was on the ground, I started work on the underhood area. There's tons of little things that needed to be done starting with fixing a couple of little coolant leaks, one at the thermo housing and one at the radiator petcock.

First I pulled the radiator to install the new petcock and cleaned up a bunch more mud from the scrap yard run. *I will NEVER drive this truck in mud again. What a pain* While the rad was out, I figured I'd put a coat of paint on it... and figured since I was gonna paint it, I might as well install the correct fan shroud(thanks tll74, as described, arrived in perfect condition)... and figured while the radiator is out, I'll fix the wiring up front... and while I'm fixing wiring, I'll install a new battery... oh, wait, Mar-K has powder-coated trays on sale(a thing of beauty, too nice for my truck)- mine's rusted out, sooo...

Long story even longer: My little project snowballed

A simple leak fix turned into a detailed renovation of the underhood area. All is well, it's things I've been meaning to do anyway, just had a severe case of the 'while I'm in theres'.

Last pic is an eBay score I got in the mail today

I like the black and gold California style they have instead of the black on white of 'normal' passenger car plates of this vintage. Now if I can just get the state to let me register them...

VA72C10 · 03-03-2011, 01:29 AM

Nice work....

...those "might as well's" will get ya every time!

Going to be worth it though!

Dinos63 · 03-03-2011, 09:45 AM

NICE AND CLEAN ,

**67cheby** · 03-03-2011, 10:10 AM

looks good

gringoloco · 03-10-2011, 01:09 AM

Did a little more work on my underhood cleanup tonight, though wasn't able to finish due to distractions and cold weather causing paint to dry sloooooowly...

Got a package in the mail today from boardmember 'otsenre'. Came well packaged as have all parts I have received from him. I got to work straight away making the booster cosmetically acceptable for bolting into my truck. I hope to be able to use the 67-70 C20 booster and bracket assembly to get the benefit of dual diaphragm while still being able to use the C10 style master. Hopefully it all fits the way I think it will

Here's some before and during disassembly pics:

gringoloco · 03-10-2011, 01:11 AM

Quote:

Originally Posted by VA72C10

Nice work...

Quote:

Originally Posted by Dinos63

NICE AND CLEAN ,

Quote:

Originally Posted by 67cheby

looks good

Thanks for checking in fellas! Nice to be back working on the old girl

gringoloco · 03-10-2011, 01:25 AM

Spent a bunch of time sanding, cleaning, and prepping for paint. I love seeing before/after pics, but unfortunately only get to show 'during' pics as paint was still tacky on the booster when I came inside

gringoloco · 03-10-2011, 01:32 AM

Also did a little finger painting with the 'new' color the truck will be getting- I couldn't help myself. Very similar to the 'old' color, just not quite as shiny

VA72C10 · 03-10-2011, 01:39 AM

Parts are looking good. And I love the flatz blue!!!

**67cheby** · 03-10-2011, 10:25 AM

cant wait to see it painted

CheyenneShop · 03-10-2011, 10:29 AM

Love the plate - nice work too

gringoloco · 03-10-2011, 10:45 PM

Almost zero progress- assembled the booster...

VA72C10 · 03-10-2011, 10:48 PM

better than zero

gringoloco · 03-12-2011, 12:06 AM

Finally (I think) settled on a seat covering. Doing the Mexican blanket thing since it's a) cheap, and b) easy which are both things I could use more of due to the limited budget and time frame. Went through a few different ones ordered off of eBay, which turned out to be NOT what was pictured and crazy (orange and then purple!) color schemes, before settling on what's in there now. Actually found them at a truck stop for $13

gringoloco · 03-12-2011, 12:22 AM

My fiance scored me a sweet new 'toolbox' on eBay (I love this woman). Also received a new toy in the form of an Eastwood welder. I've laid a few beads with it, but the jury is still out on this one- it definitely welds, but I'm not sure it is up to par with the major brands. For $299 with the gas kit and free shipping included, it should do what I need it to, at least.

Also received a box o' goodies from The Truck Shop, one of which is a pair of new dash speakers that should sound better than the ones they're replacing

Last two are before shots of the 'new' wheels I'm picking up from a board member to replace my front 6.5" van rallies. I don't feel comfortable cutting any more from the lower control arms, so I will have the 7" wheels sandblasted and powder coated. They have 3/8" less backspacing, so they should clear my suspension with the 3" Belltech drop spindles...

I'll likely do a comparo/write-up/FAQ on the different types of 5-lug rally wheels (6.5, 7, and 8 inch) describing the differences between them, since I will have one of each on hand. This is one of those questions I see asked frequently and only recently did I really come to understand the differences between them and how to properly identify them, so I hope my efforts might help other members.

brn agn · 03-12-2011, 09:56 AM

Everything is looking good. I think you definitely got your use out of the old speaker!

Mike J · 03-12-2011, 12:00 PM

Eastwood welder looks kinda like a Lincoln. Eastwood is where I bought my Lincoln, but it's been at least 10 years ago. Maybe they just rebadge them?

**FRENCHBLUE72** · 03-12-2011, 12:47 PM

Glad to see your life back in order and back to the trucks... Congrats..

hotrodhomi · 03-12-2011, 03:37 PM

I like this one. Is this the purple you're referring to? It looks blue on my MacBook.

gringoloco · 03-12-2011, 04:53 PM

Quote:

Originally Posted by brn agn

Everything is looking good. I think you definitely got your use out of the old speaker!

Yeah, someone did. I pulled it outta the local yard- my truck was bare-bones- I mainly grabbed it for the bracket...

Quote:

Originally Posted by Mike J

Eastwood welder looks kinda like a Lincoln. Eastwood is where I bought my Lincoln, but it's been at least 10 years ago. Maybe they just rebadge them?

I don't think it's a Lincoln, but I agree it does look a lot like one. It reviewed very well, so I went for it, hope I don't regret going cheap, but you know how that goes...

Quote:

Originally Posted by FRENCHBLUE72

Glad to see your life back in order and back to the trucks... Congrats..

Thanks

Good to be back.

Quote:

Originally Posted by hotrodhomi

I like this one. Is this the purple you're referring to? It looks blue on my MacBook.

Haha- wanna buy it?

Looked blue to me in pictures too...

03-01-2011, 01:45 AM	#51
CheyenneShop Registered User Join Date: Feb 2008 Location: Arizona Posts: 638	Re: How to: Ruin a perfectly good C10 nice work __________________ 72 Cheyenne shorty "*CheyLow" 72 3/4 long 4X4 69 SWB "Prospector" 68 C/10 shorty - "Picacho"* http://67-72chevytrucks.com/vboard/s...d.php?t=428379 *sold to "93redsled"* Have you heard about *C10 Talk? C10 Talk* is a podcast all about C10 Trucks, the builders, the vendors, and most importantly the C10 Community. Check us out online at www.c10talk.com

03-01-2011, 02:00 AM	#52
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: How to: Ruin a perfectly good C10 Nice! Love a clean undercarriage!!! __________________ Looking for a 67-72 swb or blazer project in or around VA.

03-01-2011, 10:31 PM	#53
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: How to: Ruin a perfectly good C10 Painted the spindles, calipers, rotors, and other miscellaneous stuff. Had to get a shot of the brake dust shields since I have way more time than I care to share in cleaning them Also lopped a full coil off of the brand new springs (cheaper than new drop springs) and got the driver's side assembled. I'll get it on the ground tomorrow and see if I need to trim the springs any more. Also had an upper control arm stud start spinning on me, so I need to do something about that before it goes out for alignment... The before/after shot makes it all worth it Attached Images __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

03-01-2011, 11:53 PM	#54
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: How to: Ruin a perfectly good C10 Very nice work! Did you clear the cross shafts or paint them? What colors? Wanting to paint my suspension parts the correct colors.... __________________ Looking for a 67-72 swb or blazer project in or around VA.

03-03-2011, 12:51 AM	#56
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: How to: Ruin a perfectly good C10 Got the suspension reassembled and put her back on the ground. Forgot just how low she actually sits when not on jackstands I ended up using the Belltech drop coils that were previously installed since I couldn't get the Moogs to seat properly??? I dunno- the Belltechs dropped right in. Still need to do a little more clearancing on the LCAs; since I'm running van rallies with 3" drop spindles, they rub the wheels when turning sharply. Once it was on the ground, I started work on the underhood area. There's tons of little things that needed to be done starting with fixing a couple of little coolant leaks, one at the thermo housing and one at the radiator petcock. First I pulled the radiator to install the new petcock and cleaned up a bunch more mud from the scrap yard run. I will NEVER drive this truck in mud again. What a pain While the rad was out, I figured I'd put a coat of paint on it... and figured since I was gonna paint it, I might as well install the correct fan shroud(thanks tll74, as described, arrived in perfect condition)... and figured while the radiator is out, I'll fix the wiring up front... and while I'm fixing wiring, I'll install a new battery... oh, wait, Mar-K has powder-coated trays on sale(a thing of beauty, too nice for my truck)- mine's rusted out, sooo... Long story even longer: My little project snowballed A simple leak fix turned into a detailed renovation of the underhood area. All is well, it's things I've been meaning to do anyway, just had a severe case of the 'while I'm in theres'. Last pic is an eBay score I got in the mail today I like the black and gold California style they have instead of the black on white of 'normal' passenger car plates of this vintage. Now if I can just get the state to let me register them... Attached Images __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

03-03-2011, 01:29 AM	#57
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: How to: Ruin a perfectly good C10 Nice work.... ...those "might as well's" will get ya every time! Going to be worth it though! __________________ Looking for a 67-72 swb or blazer project in or around VA.

03-03-2011, 09:45 AM	#58
Dinos63 chevy only Join Date: Sep 2006 Location: Phoenix, AZ Posts: 6,619	Re: How to: Ruin a perfectly good C10 NICE AND CLEAN , __________________ CHEVY ONLY... Nothin Else !

03-03-2011, 10:10 AM	#59
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: How to: Ruin a perfectly good C10 looks good __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

03-10-2011, 01:09 AM	#60
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: How to: Ruin a perfectly good C10 Did a little more work on my underhood cleanup tonight, though wasn't able to finish due to distractions and cold weather causing paint to dry sloooooowly... Got a package in the mail today from boardmember 'otsenre'. Came well packaged as have all parts I have received from him. I got to work straight away making the booster cosmetically acceptable for bolting into my truck. I hope to be able to use the 67-70 C20 booster and bracket assembly to get the benefit of dual diaphragm while still being able to use the C10 style master. Hopefully it all fits the way I think it will Here's some before and during disassembly pics: Attached Images __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

03-10-2011, 01:25 AM	#62
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: How to: Ruin a perfectly good C10 Spent a bunch of time sanding, cleaning, and prepping for paint. I love seeing before/after pics, but unfortunately only get to show 'during' pics as paint was still tacky on the booster when I came inside Attached Images __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

03-10-2011, 01:32 AM	#63
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: How to: Ruin a perfectly good C10 Also did a little finger painting with the 'new' color the truck will be getting- I couldn't help myself. Very similar to the 'old' color, just not quite as shiny Attached Images __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

03-10-2011, 01:39 AM	#64
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: How to: Ruin a perfectly good C10 Parts are looking good. And I love the flatz blue!!! __________________ Looking for a 67-72 swb or blazer project in or around VA.

03-10-2011, 10:25 AM	#65
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: How to: Ruin a perfectly good C10 cant wait to see it painted __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

03-10-2011, 10:29 AM	#66
CheyenneShop Registered User Join Date: Feb 2008 Location: Arizona Posts: 638	Re: How to: Ruin a perfectly good C10 Love the plate - nice work too __________________ 72 Cheyenne shorty "*CheyLow" 72 3/4 long 4X4 69 SWB "Prospector" 68 C/10 shorty - "Picacho"* http://67-72chevytrucks.com/vboard/s...d.php?t=428379 *sold to "93redsled"* Have you heard about *C10 Talk? C10 Talk* is a podcast all about C10 Trucks, the builders, the vendors, and most importantly the C10 Community. Check us out online at www.c10talk.com

03-10-2011, 10:45 PM	#67
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: How to: Ruin a perfectly good C10 Almost zero progress- assembled the booster... Attached Images __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy



Register or Log In To remove these advertisements.

03-10-2011, 10:48 PM	#68
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: How to: Ruin a perfectly good C10 better than zero __________________ Looking for a 67-72 swb or blazer project in or around VA.

03-12-2011, 12:06 AM	#69
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: How to: Ruin a perfectly good C10 Finally (I think) settled on a seat covering. Doing the Mexican blanket thing since it's a) cheap, and b) easy which are both things I could use more of due to the limited budget and time frame. Went through a few different ones ordered off of eBay, which turned out to be NOT what was pictured and crazy (orange and then purple!) color schemes, before settling on what's in there now. Actually found them at a truck stop for $13 Attached Images __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

03-12-2011, 12:22 AM	#70
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: How to: Ruin a perfectly good C10 My fiance scored me a sweet new 'toolbox' on eBay (I love this woman). Also received a new toy in the form of an Eastwood welder. I've laid a few beads with it, but the jury is still out on this one- it definitely welds, but I'm not sure it is up to par with the major brands. For $299 with the gas kit and free shipping included, it should do what I need it to, at least. Also received a box o' goodies from The Truck Shop, one of which is a pair of new dash speakers that should sound better than the ones they're replacing Last two are before shots of the 'new' wheels I'm picking up from a board member to replace my front 6.5" van rallies. I don't feel comfortable cutting any more from the lower control arms, so I will have the 7" wheels sandblasted and powder coated. They have 3/8" less backspacing, so they should clear my suspension with the 3" Belltech drop spindles... I'll likely do a comparo/write-up/FAQ on the different types of 5-lug rally wheels (6.5, 7, and 8 inch) describing the differences between them, since I will have one of each on hand. This is one of those questions I see asked frequently and only recently did I really come to understand the differences between them and how to properly identify them, so I hope my efforts might help other members. Attached Images __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy Last edited by gringoloco; 03-12-2011 at 12:34 AM.

03-12-2011, 09:56 AM	#71
brn agn Registered User Join Date: Mar 2009 Location: Youngsville, NC Posts: 952	Re: How to: Ruin a perfectly good C10 Everything is looking good. I think you definitely got your use out of the old speaker! __________________ 1969 C10 SWB Project Charity Case AKA "Roscoe" 1971 Cheyenne Super A Combined Effort The Service Station-A practical ministry for those in need

03-12-2011, 12:00 PM	#72
Mike J vw guy & now c-10 guy Join Date: Sep 2008 Location: Louisville,KY Posts: 483	Re: How to: Ruin a perfectly good C10 Eastwood welder looks kinda like a Lincoln. Eastwood is where I bought my Lincoln, but it's been at least 10 years ago. Maybe they just rebadge them? __________________ '68 long fleet Finally made some progress on the build!!! My Build Thread

03-12-2011, 12:47 PM	#73
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,608	Re: How to: Ruin a perfectly good C10 Glad to see your life back in order and back to the trucks... Congrats.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

03-12-2011, 03:37 PM	#74
hotrodhomi Registered User Join Date: Apr 2004 Location: Sacramento Posts: 3,737	Re: How to: Ruin a perfectly good C10 I like this one. Is this the purple you're referring to? It looks blue on my MacBook. __________________ '72 2wd blazer, bagged w/ watts link & EDC '72 C10 "Lowered Farm Truck" STOLEN 5-18-11 '66 impala ht Last edited by hotrodhomi; 03-12-2011 at 03:39 PM.

Register or Log In To remove these advertisements.