Started my first frame off - 72 SWB LS1, 6-spd manual - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

trkfrk · 12-24-2010, 04:03 PM

making a little progress -I bolted in the engine and transmission where I want it. I installed the notch kit into the frame. machined both front rotors to fit the Boss 338's 20x10 rears and 18x8's up front.

67C10BUB · 12-24-2010, 04:37 PM

Very nice. Keep up the good work.

butternut1972 · 12-24-2010, 05:36 PM

Excellent! Cool project.

mcbassin · 12-24-2010, 05:44 PM

This is a great looking project! Looks like a bonafied frame off. You might want to have the thread moved to the build and project section. Subscribed.

mcmlxix · 12-24-2010, 06:48 PM

Nice. How come you have TWO LSx motors?

mcbassin · 12-24-2010, 07:19 PM

I couldn't help but notice the longer studs up front on your rotor. I assume you are running a thin spacer behind your front wheels? Is this how you got your Boss center caps to fit on there without cutting the spindle shaft and dust cover? I'm pretty familiar with the 338 mods required on the rotorsHere.

19seventeeCustom · 12-24-2010, 11:27 PM

looks fantastic so far, keep up the good work

trkfrk · 12-25-2010, 11:58 PM

Thanks for the compliments...

mcbassin, your correct. I am running 1/4" spacer on the front wheels.. Thanks to everyone like you on this board did all of the leg work for me...

Quote:

Originally Posted by mcmlxix

Nice. How come you have TWO LSx motors?

This is my buddy's Sand Car engine. Trading labor; I am rebuilding his transmission, and he will powder coat my frame. Check out Powdercoatingplus here in Vegas..

69CST-V · 12-26-2010, 12:09 AM

Looks like a cool build. Can't wait to see more.

hick · 12-26-2010, 05:27 AM

Quote:

Originally Posted by trkfrk

Thanks for the compliments...

mcbassin, your correct. I am running 1/4" spacer on the front wheels.. Thanks to everyone like you on this board did all of the leg work for me...

This is my buddy's Sand Car engine. Trading labor; I am rebuilding his transmission, and he will powder coat my frame. Check out Powdercoatingplus here in Vegas..

I used to live 5 miles from APEX when I lived in Vegas... I am positive I have seen this thing either there or dumont the few times i went. If it is infact the same one, this thing is intimating as all hell, haha.

RCbowtie69 · 12-26-2010, 09:26 AM

nice job on the cab,wheels are going to look great!! Keep on Truckin'',

Jacfourteen · 12-26-2010, 03:19 PM

Great to see progress! I bet that rail moves!

ChuckDriver · 12-26-2010, 08:44 PM

Nice work!

Hoffa · 12-27-2010, 02:48 AM

Great work. The six speed is cool. Subscribed!

mcmlxix · 02-05-2011, 05:44 AM

any progress?

dixietruck71 · 02-05-2011, 10:28 AM

very nice! i like how you turned down your rotor hub to fit the wheel instead of going the wheel spacer route.

trkfrk · 02-05-2011, 01:00 PM

Frame just made it back from PC.

mcbassin · 02-05-2011, 01:06 PM

Man that frame looks awesome! That engine looks great in there too. Are your bolts chromed or polished stainless? Keep the pics coming!

weircc · 02-05-2011, 01:09 PM

looks killer man love the color on the frame

*mrhino* · 02-05-2011, 02:11 PM

bad @ss! I'm jealous

BLACK AND BLUE 67-72 · 02-05-2011, 02:13 PM

Sweet!! It looks awesome so far!!!

tantrumpipeline · 02-05-2011, 09:14 PM

Wow!!!! I don't even know what to say? Very nice

srea76 · 02-05-2011, 09:51 PM

Ok sorry if I sound too crude, but my heart just fluttered when I seen that.

VA72C10 · 02-05-2011, 11:29 PM

Awesome!!!

dixietruck71 · 02-06-2011, 12:31 AM

Very nice!

12-24-2010, 04:03 PM	#51
trkfrk Registered User Join Date: Jul 2010 Location: Las Vegas, NV Posts: 969	Re: Started my first frame off - 72 SWB LS1, 6-spd manual making a little progress -I bolted in the engine and transmission where I want it. I installed the notch kit into the frame. machined both front rotors to fit the Boss 338's 20x10 rears and 18x8's up front. __________________ Mark 1972 C10 SWB LS1/T56 6 speed trans/4:56 posi with 5.5"-7" static drop/Boss 338 Wheels 18"x20" My build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=424609. My first start up http://youtu.be/R899YQ1OcjU

12-24-2010, 04:37 PM	#52
67C10BUB Registered User Join Date: Aug 2010 Location: Alta Loma, CA Posts: 610	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Very nice. Keep up the good work. __________________ 67 5.3L Build

12-24-2010, 05:36 PM	#53
butternut1972 Registered User Join Date: May 2009 Location: longview,wa Posts: 1,094	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Excellent! Cool project.

12-24-2010, 05:44 PM	#54
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: Started my first frame off - 72 SWB LS1, 6-spd manual This is a great looking project! Looks like a bonafied frame off. You might want to have the thread moved to the build and project section. Subscribed. __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

12-24-2010, 06:48 PM	#55
mcmlxix Collector of Projects Join Date: Apr 2003 Location: Las Vegas Posts: 3,106	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Nice. How come you have TWO LSx motors? __________________ Rich 1972 K5 Blazer CST Click HERE D60 BIG BRAKE UPGRADE Click HERE

12-24-2010, 07:19 PM	#56
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: Started my first frame off - 72 SWB LS1, 6-spd manual I couldn't help but notice the longer studs up front on your rotor. I assume you are running a thin spacer behind your front wheels? Is this how you got your Boss center caps to fit on there without cutting the spindle shaft and dust cover? I'm pretty familiar with the 338 mods required on the rotorsHere. __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group Last edited by mcbassin; 12-24-2010 at 07:22 PM.

12-24-2010, 11:27 PM	#57
19seventeeCustom Registered User Join Date: Mar 2010 Location: Downtown Posts: 573	Re: Started my first frame off - 72 SWB LS1, 6-spd manual looks fantastic so far, keep up the good work

12-26-2010, 12:09 AM	#59
69CST-V Registered User Join Date: Mar 2010 Location: Piper, KS Posts: 683	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Looks like a cool build. Can't wait to see more. __________________ Bryce '69 SWB Fleet Still Under Construction Company Trucks

12-26-2010, 09:26 AM	#61
RCbowtie69 Registered User Join Date: Dec 2003 Location: Thomasville, NC Posts: 1,877	Re: Started my first frame off - 72 SWB LS1, 6-spd manual nice job on the cab,wheels are going to look great!! Keep on Truckin'',

12-26-2010, 03:19 PM	#62
Jacfourteen Big Red - Now its a SWB! Join Date: Jun 2009 Location: Oroville, Ca Posts: 1,624	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Great to see progress! I bet that rail moves! __________________ 68 3/4 ton (Project)-350 Small Block, .030 over, 10:1 comp, 3998993 heads, C3BX edelbrock intake, comp cams XE268, Holley 670 SA, long tube headers, dual flow 40's, E-fan, Alum rad, currently under the knife getting shortened and bagged build thread 41 3/4 ton (wife's)-flatbed, fully restored to original 01 Tahoe LT 4WD (my daily driver)-Magnaflow Muffler, Rollin on 22's 02 Ford Mustang Convertable (Wife's Car)-Flowmaster 50, Clear corners, Intake, sittin on 18's

12-26-2010, 08:44 PM	#63
ChuckDriver A320 Pilot/USAF Retired Join Date: Mar 2009 Location: Charleston, SC Posts: 2,629	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Nice work! __________________ JJ My 1957 build: http://67-72chevytrucks.com/vboard/s...d.php?t=334552 http://www.trifive.com/forums/showthread.php?t=22037 Instagram - Chuckdriver57

12-27-2010, 02:48 AM	#64
Hoffa Registered User Join Date: Oct 2006 Location: Roseburg, Oregon Posts: 105	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Great work. The six speed is cool. Subscribed! __________________ 68 Chev SWB 2WD w/'95 LT1, 6spd, 4:56, 17" whls - family owned since 1973. 70 GMC LWB 4WD w/RAMJET 350, 4spd, 4inch lift, 33" tires, Warn Winch 72 Chev Blazer CST, 350, TH350, 4WD, factory A/C, tilt, radio delete, 77K miles, orig. paint/interior

02-05-2011, 05:44 AM	#65
mcmlxix Collector of Projects Join Date: Apr 2003 Location: Las Vegas Posts: 3,106	Re: Started my first frame off - 72 SWB LS1, 6-spd manual any progress? __________________ Rich 1972 K5 Blazer CST Click HERE D60 BIG BRAKE UPGRADE Click HERE

02-05-2011, 10:28 AM	#66
dixietruck71 Registered User Join Date: Dec 2010 Location: ravensdale washington Posts: 111	Re: Started my first frame off - 72 SWB LS1, 6-spd manual very nice! i like how you turned down your rotor hub to fit the wheel instead of going the wheel spacer route. __________________ 71 gme Sierra Grande lwb. 68 Rambler American 2 door 75 jeep cj5

02-05-2011, 01:00 PM	#67
trkfrk Registered User Join Date: Jul 2010 Location: Las Vegas, NV Posts: 969	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Frame just made it back from PC. __________________ Mark 1972 C10 SWB LS1/T56 6 speed trans/4:56 posi with 5.5"-7" static drop/Boss 338 Wheels 18"x20" My build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=424609. My first start up http://youtu.be/R899YQ1OcjU



Register or Log In To remove these advertisements.

02-05-2011, 01:06 PM	#68
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Man that frame looks awesome! That engine looks great in there too. Are your bolts chromed or polished stainless? Keep the pics coming! __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group Last edited by mcbassin; 02-05-2011 at 02:41 PM.

02-05-2011, 01:09 PM	#69
weircc Registered User Join Date: Dec 2008 Location: richmond, MO Posts: 794	Re: Started my first frame off - 72 SWB LS1, 6-spd manual looks killer man love the color on the frame

02-05-2011, 02:11 PM	#70
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: Started my first frame off - 72 SWB LS1, 6-spd manual bad @ss! I'm jealous

02-05-2011, 02:13 PM	#71
BLACK AND BLUE 67-72 Firefighter Join Date: Feb 2001 Location: Yellville, Ar, USA Posts: 1,943	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Sweet!! It looks awesome so far!!! __________________ '72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA

02-05-2011, 09:14 PM	#72
tantrumpipeline Master Procrastinator Join Date: Sep 2009 Location: Grande Prairie AB Canada Posts: 1,128	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Wow!!!! I don't even know what to say? Very nice __________________ My Buildhttp://67-72chevytrucks.com/vboard/s...d.php?t=395506 20 Duramax tow pig 68 2wd short stepper project 77 2wd short fleet beater 52 short project

02-05-2011, 09:51 PM	#73
srea76 Registered User Join Date: Nov 2009 Location: Hazlehurst, Ga. Posts: 822	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Ok sorry if I sound too crude, but my heart just fluttered when I seen that. __________________ 1972 Custom Deluxe LT1 Gen V Swap "Green Lantern" 1984 Silverado Red Baron-72 c10 Project Last edited by augie; 02-05-2011 at 10:44 PM. Reason: family friendly

02-05-2011, 11:29 PM	#74
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Awesome!!! __________________ Looking for a 67-72 swb or blazer project in or around VA.

02-06-2011, 12:31 AM	#75
dixietruck71 Registered User Join Date: Dec 2010 Location: ravensdale washington Posts: 111	Re: Started my first frame off - 72 SWB LS1, 6-spd manual Very nice! __________________ 71 gme Sierra Grande lwb. 68 Rambler American 2 door 75 jeep cj5

Register or Log In To remove these advertisements.