GM connect and cruise engine package - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Oldironracing · 07-10-2018, 11:08 PM

One more

Oldironracing · 07-10-2018, 11:10 PM

Some more that got done.

Oldironracing · 07-10-2018, 11:11 PM

Some more pic

Oldironracing · 07-10-2018, 11:12 PM

Can't post but one pic at a time ?

Oldironracing · 07-10-2018, 11:14 PM

Made my on pedal bracket using the factory holes.

Oldironracing · 07-12-2018, 11:28 PM

My motor sets to high in the front. I have the CPP motor stands with dirty dingo sliders. I'm at 6 degrees with a degree finder on the top of the intake. What s up? Are any one else haveing the same trouble? I used the original trans cross member.

Oldironracing · 07-12-2018, 11:33 PM

How do I make this a build thread or link? Rename it or move it?

Ric's/86 · 08-10-2018, 09:20 PM

Did you figure out the problem?

Oldironracing · 01-02-2019, 12:04 AM

Still have not found the fix to the exstream angle of motor. I can put a3/4 spacer under trans crossmember and get it to 5* but trans touches front of trans tunnel at pinch weld.

davepl · 01-03-2019, 10:00 AM

Can the motor come forward then on its mounts so the back of the trans can come up more?

Oldironracing · 01-03-2019, 10:05 AM

Can't move forward,won't have room for air intake tube between motor and fans

Oldironracing · 01-05-2019, 09:11 PM

Ok up date on truck been a lot going on. Holley front drive installed air intake built brake lines made and run motor back in and now build a exhaust.

Oldironracing · 01-05-2019, 09:12 PM

How do u load more than one picture at a time?

my kids toy · 01-06-2019, 06:34 AM

Whos top rad mount did you use ?

Oldironracing · 01-06-2019, 04:43 PM

Made my own. Trying to post pictures.

Oldironracing · 01-06-2019, 04:52 PM

Got pic to upload finally. Added this two sence last post. White 70 is a driver and the blue is work in progress.

Oldironracing · 01-06-2019, 04:53 PM

Pic. Upload

Oldironracing · 01-06-2019, 04:54 PM

Pic

Oldironracing · 01-06-2019, 04:55 PM

Pic.

Oldironracing · 01-06-2019, 05:01 PM

Pic.

bigmoe · 01-07-2019, 12:38 AM

Quote:

Originally Posted by Oldironracing

My motor sets to high in the front. I have the CPP motor stands with dirty dingo sliders. I'm at 6 degrees with a degree finder on the top of the intake. What s up? Are any one else haveing the same trouble? I used the original trans cross member.

I wouldn't measure the angle on the top of the motor. You need the angle at the trans tail shaft. Then you match that angle at the rear end pinion. 3 degrees down and 3 degrees up is good. Often you have to tweek it after all the weight is on the wheels. You can do that on the trans crossmember or angled shims on the spring perches. If you draw an imaginary line back from the trans output shaft, and another line forward from the rear pinion, the two lines should be parallel. Google image driveline angles and get some good explanation.

bigmoe · 01-07-2019, 12:40 AM

https://ls1tech.com/forums/gears-axl...in-angles.html

Oldironracing · 01-07-2019, 10:38 AM

At the crank front pulley I have 4*now. Thank I'll be good for now.

bigmoe · 01-07-2019, 12:47 PM

Quote:

Originally Posted by Oldironracing

At the crank front pulley I have 4*now. Thank I'll be good for now.

Front pulley would work too. Good idea. Gonna have to remember that one.

Oldironracing · 01-09-2019, 12:29 AM

What r u guys doing for exhaust and what muffler?

07-10-2018, 11:08 PM	#51
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package One more Attached Images __________________ OLDIRONRACING

07-10-2018, 11:10 PM	#52
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Some more that got done. Attached Images __________________ OLDIRONRACING

07-10-2018, 11:11 PM	#53
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Some more pic Attached Images __________________ OLDIRONRACING

07-10-2018, 11:12 PM	#54
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Can't post but one pic at a time ? Attached Images __________________ OLDIRONRACING

07-10-2018, 11:14 PM	#55
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Made my on pedal bracket using the factory holes. Attached Images __________________ OLDIRONRACING

07-12-2018, 11:28 PM	#56
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package My motor sets to high in the front. I have the CPP motor stands with dirty dingo sliders. I'm at 6 degrees with a degree finder on the top of the intake. What s up? Are any one else haveing the same trouble? I used the original trans cross member. __________________ OLDIRONRACING

07-12-2018, 11:33 PM	#57
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package How do I make this a build thread or link? Rename it or move it? __________________ OLDIRONRACING

08-10-2018, 09:20 PM	#58
Ric's/86 Registered User Join Date: Dec 2013 Location: Ocala Fl Posts: 37	Re: GM connect and cruise engine package Did you figure out the problem?

01-02-2019, 12:04 AM	#59
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Still have not found the fix to the exstream angle of motor. I can put a3/4 spacer under trans crossmember and get it to 5* but trans touches front of trans tunnel at pinch weld. __________________ OLDIRONRACING Last edited by Oldironracing; 01-02-2019 at 12:14 AM.

01-03-2019, 10:00 AM	#60
davepl Registered User Join Date: Aug 2006 Location: Redmond, WA Posts: 6,332	Re: GM connect and cruise engine package Can the motor come forward then on its mounts so the back of the trans can come up more? __________________ 1970 GMC Sierra Grande Custom Camper - Built, not Bought 1969 Pontiac 2+2 427/390 4-speed Coupe 1969 Pontiac 2+2 427/390 4-speed Convertible

01-03-2019, 10:05 AM	#61
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Can't move forward,won't have room for air intake tube between motor and fans __________________ OLDIRONRACING

01-05-2019, 09:11 PM	#62
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Ok up date on truck been a lot going on. Holley front drive installed air intake built brake lines made and run motor back in and now build a exhaust. Attached Images __________________ OLDIRONRACING

01-05-2019, 09:12 PM	#63
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package How do u load more than one picture at a time? __________________ OLDIRONRACING

01-06-2019, 06:34 AM	#64
my kids toy Registered User Join Date: May 2018 Location: Grand Haven, mi Posts: 269	Re: GM connect and cruise engine package Whos top rad mount did you use ?

01-06-2019, 04:43 PM	#65
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Made my own. Trying to post pictures. __________________ OLDIRONRACING



Register or Log In To remove these advertisements.

01-06-2019, 04:52 PM	#66
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Got pic to upload finally. Added this two sence last post. White 70 is a driver and the blue is work in progress. Attached Images __________________ OLDIRONRACING

01-06-2019, 04:53 PM	#67
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Pic. Upload Attached Images __________________ OLDIRONRACING

01-06-2019, 04:54 PM	#68
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Pic Attached Images __________________ OLDIRONRACING

01-06-2019, 04:55 PM	#69
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Pic. Attached Images __________________ OLDIRONRACING

01-06-2019, 05:01 PM	#70
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package Pic. Attached Images __________________ OLDIRONRACING

01-07-2019, 12:40 AM	#72
bigmoe Registered User Join Date: Oct 2014 Location: Brandon, Manitoba, Canada Posts: 993	Re: GM connect and cruise engine package https://ls1tech.com/forums/gears-axl...in-angles.html

01-07-2019, 10:38 AM	#73
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package At the crank front pulley I have 4*now. Thank I'll be good for now. __________________ OLDIRONRACING

01-09-2019, 12:29 AM	#75
Oldironracing Registered User Join Date: Oct 2007 Location: Austin Arkansas Posts: 252	Re: GM connect and cruise engine package What r u guys doing for exhaust and what muffler? __________________ OLDIRONRACING

Register or Log In To remove these advertisements.