My "new" 1968 c20 - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

72c20customcamper · 07-16-2019, 09:06 AM

Could this thread be moved to the build section?

**special-K** · 07-17-2019, 07:49 AM

Yes, but there is a $20 fee and request must be submitted for evaluation and approval no less than 60 days prior to targeted "move" date, at which time you will be notified and given 5 minutes to accept or new application/fee will be required. If you agree to these terms please give response in next post please.

72c20customcamper · 07-17-2019, 08:21 AM

Quote:

Originally Posted by special-K

Yes, but there is a $20 fee and request must be submitted for evaluation and approval no less than 60 days prior to targeted "move" date, at which time you will be notified and given 5 minutes to accept or new application/fee will be required. If you agree to these terms please give response in next post please.

thanks Tim

72c20customcamper · 07-17-2019, 08:22 AM

Yesterday dry run of the bed bolt holes .

72c20customcamper · 07-17-2019, 03:51 PM

All the holes worked out perfectly. Helps having a drill press too. Had a hard time finding a 1 9/16ths fostner bit. Girl at the local wood working shop broke up a set for me. Sanded and sealed the undersides of the bed wood this afternoon.

cornerstone · 07-18-2019, 12:14 AM

Looking fantastic!

Are you building this to keep? I wish I was able to dedicate half the time you do!!

72c20customcamper · 07-19-2019, 08:25 AM

Quote:

Originally Posted by cornerstone

Looking fantastic!

Are you building this to keep? I wish I was able to dedicate half the time you do!!

That's was the plan. But I just bought a Suburban so something will go.

Helps that I'm retired so I pretty much treat the truck like a job 5 for 6 hours a day

72c20customcamper · 07-19-2019, 08:47 AM

Neglected to post the planning of the boards. Very little warp to them so I only needed to shim one board to make a flat surface. Basic skip planning

72c20customcamper · 07-19-2019, 12:18 PM

Boards are done . 12 hours to dry and then I can start the assembly. I used a method a friend who does high end cabinetry and furniture taught me. Basically its wet sanding with oil and 400 paper the sanding creates a slurry of oil and saw dust I usually do this by hand with regular garnet paper but 8 8ft boards would have taken forever. You keep adding oil until the wood no longer takes it in. Use much more oil but goes deaper into the wood and the slurry acts like a grain filler too.

Just need to take the side boards out from the bed a do them

**68bowtie** · 07-19-2019, 09:05 PM

Looking good

**3757chevy** · 07-21-2019, 12:27 AM

Looking great. What kind of oil ? If you don't mind me asking.

72c20customcamper · 07-21-2019, 10:16 AM

Penofin marine oil good for million dollar yachts good enough for my truck bed. Started the assembly yesterday.

72c20customcamper · 07-25-2019, 12:46 PM

Bed finished . Now on to the cab.

Hope to find a nice tailgate in Carlisle next weekend

cornerstone · 07-25-2019, 04:10 PM

Wow, that looks super.

I have to admit, I'm a bit jealous of guys that get to spend a good amount of their time working on cool stuff. Hopefully my turn will come sooner than later.

72c20customcamper · 07-25-2019, 05:52 PM

Quote:

Originally Posted by cornerstone

Wow, that looks super.

I have to admit, I'm a bit jealous of guys that get to spend a good amount of their time working on cool stuff. Hopefully my turn will come sooner than later.

Paid my dues on the job working the clock for 20 then started my own insurance agency. Been a long road but it's been worth it

cornerstone · 07-25-2019, 08:46 PM

Quote:

Originally Posted by 72c20customcamper

Paid my dues on the job working the clock for 20 then started my own insurance agency. Been a long road but it's been worth it

Hard work has its rewards! Envious probably would have been a better word choice, but either way, I'm glad you post your rapid progress!

I found a rust free step side bed with what looks to have a very nice tailgate. He wants 600. bucks and says he wont part it out. How much would a clean original gate go for if he would? I wouldn't mind going to see it in person and give it a try... Sometimes in the past I've even considered having a step side bed to swap out on my truck just to change it up every now and then.
I dont know how to add a link or I would show you the add. Look in the Dallas Craigslist auto / truck parts and search c10 if you're interested.

72c20customcamper · 07-28-2019, 07:42 PM

Not sure what a nice gate brings . The beds were the same from 67 to I believe 87 so there should be alot of nice ones out there.

72c20customcamper · 07-28-2019, 07:43 PM

Sounds good but a road trip to Dallas for a tailgate is a bit much even for me

72c20customcamper · 08-06-2019, 07:44 PM

Quote:

Originally Posted by 72c20customcamper

Bed finished . Now on to the cab.

Hope to find a nice tailgate in Carlisle next weekend

Found a nice gate . No dents or bows the pic on the table looks bowed but it's an optical illusion.
Just a little surface rust and a couple of small holes for what looks like tonneau cover snaps

cornerstone · 08-06-2019, 09:30 PM

Nice find! Is it a GM piece or repop? Mind if I ask what that set you back?

72c20customcamper · 08-06-2019, 09:53 PM

Quote:

Originally Posted by cornerstone

Nice find! Is it a GM piece or repop? Mind if I ask what that set you back?

Its OEM. I am reluctant to buy repop parts. About the same as a repop item

cornerstone · 08-06-2019, 10:48 PM

Thanks! Can't beat factory metal.

**lolife99** · 08-07-2019, 10:32 AM

Quote:

Originally Posted by 72c20customcamper

Its OEM. I am reluctant to buy repop parts. About the same as a repop item

I wouldn't be afraid to buy a new tail gate from Mar-K out of Oklahoma.
http://www.mar-k.com/Catalog/index.aspx?LID=384
They are NICER than GM's NOS tail gates.
I've seen them side by side.
Very high quality.
OEM tailgates have spot welds all over the place.
The Mar-K version has them evenly spaced to satisfy my OCD. Ha.

72c20customcamper · 08-08-2019, 01:36 PM

I looked at the Mar-k gate . Only thing that killed it for me was the shipping. They must higher an uber driver to deliver it.

But the gate is down to bare metal.

**lolife99** · 08-08-2019, 02:20 PM

Quote:

Originally Posted by 72c20customcamper

I looked at the Mar-k gate . Only thing that killed it for me was the shipping. They must higher an uber driver to deliver it.

Mar-K usually ships their parts in wooden crates to prevent damage.
Including all of the side mouldings they sell.

07-16-2019, 09:06 AM	#51
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,713	Re: My "new" 1968 c20 Could this thread be moved to the build section? __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

07-17-2019, 07:49 AM	#52
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: My "new" 1968 c20 Yes, but there is a $20 fee and request must be submitted for evaluation and approval no less than 60 days prior to targeted "move" date, at which time you will be notified and given 5 minutes to accept or new application/fee will be required. If you agree to these terms please give response in next post please. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

07-17-2019, 08:22 AM	#54
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,713	Re: My "new" 1968 c20 Yesterday dry run of the bed bolt holes . Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

07-17-2019, 03:51 PM	#55
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,713	Re: My "new" 1968 c20 All the holes worked out perfectly. Helps having a drill press too. Had a hard time finding a 1 9/16ths fostner bit. Girl at the local wood working shop broke up a set for me. Sanded and sealed the undersides of the bed wood this afternoon. Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

07-18-2019, 12:14 AM	#56
cornerstone Registered User Join Date: Apr 2014 Location: Azle,Texas Posts: 2,248	Re: My "new" 1968 c20 Looking fantastic! Are you building this to keep? I wish I was able to dedicate half the time you do!! __________________ Brian 1972 C10, "Loyd", LWB to SWB, 5.3, L83/6L80e, 4:11 Tru Trac, Air Ride, VA, DD, 20" Coys, 4 wheel disc, A quick LS swap turned into a 6 year frame off resto-mod.

07-19-2019, 08:47 AM	#58
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,713	Re: My "new" 1968 c20 Neglected to post the planning of the boards. Very little warp to them so I only needed to shim one board to make a flat surface. Basic skip planning Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary. Last edited by 72c20customcamper; 07-19-2019 at 12:07 PM.

07-19-2019, 12:18 PM	#59
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,713	Re: My "new" 1968 c20 Boards are done . 12 hours to dry and then I can start the assembly. I used a method a friend who does high end cabinetry and furniture taught me. Basically its wet sanding with oil and 400 paper the sanding creates a slurry of oil and saw dust I usually do this by hand with regular garnet paper but 8 8ft boards would have taken forever. You keep adding oil until the wood no longer takes it in. Use much more oil but goes deaper into the wood and the slurry acts like a grain filler too. Just need to take the side boards out from the bed a do them Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

07-19-2019, 09:05 PM	#60
68bowtie Senior Member Join Date: Jan 2007 Location: Turlock, CA Posts: 8,795	Re: My "new" 1968 c20 Looking good __________________ Please help my sister in law with her battle with cancer https://gofund.me/902f6fce Project "C10 Fever" (68 factory black 396 swb) Project "Little Sister" (70 c10 blue original paint refresh) Project "Blue Bomb" (70 c30 blue original paint refresh) SOLD Project "Vitamin C" (71 c10 orange original paint refresh) SOLD

07-21-2019, 12:27 AM	#61
3757chevy Senior Member Join Date: Mar 2016 Location: Near Canon City ,Colorado Posts: 4,056	Re: My "new" 1968 c20 Looking great. What kind of oil ? If you don't mind me asking. __________________ '35 1/2 ton Pickup (bought 2020) '68 C10 Suburban (bought 2021) '72 K5 Blazer (bought 2013) '67 Stepside (bought 1997-sold 2021) '96 Bronco Eddie Bauer (inherited 2010) My 1st day here-'67 C10(sold)and '72 K5 Blazer http://67-72chevytrucks.com/vboard/s...d.php?t=702056 "Another Blue Chevy"(1935) http://67-72chevytrucks.com/vboard/s...d.php?t=799203 '68 Burb...https://67-72chevytrucks.com/vboard/...d.php?t=822994 MIKE

07-21-2019, 10:16 AM	#62
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,713	Re: My "new" 1968 c20 Penofin marine oil good for million dollar yachts good enough for my truck bed. Started the assembly yesterday. Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

07-25-2019, 12:46 PM	#63
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,713	Re: My "new" 1968 c20 Bed finished . Now on to the cab. Hope to find a nice tailgate in Carlisle next weekend Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

07-25-2019, 04:10 PM	#64
cornerstone Registered User Join Date: Apr 2014 Location: Azle,Texas Posts: 2,248	Re: My "new" 1968 c20 Wow, that looks super. I have to admit, I'm a bit jealous of guys that get to spend a good amount of their time working on cool stuff. Hopefully my turn will come sooner than later. __________________ Brian 1972 C10, "Loyd", LWB to SWB, 5.3, L83/6L80e, 4:11 Tru Trac, Air Ride, VA, DD, 20" Coys, 4 wheel disc, A quick LS swap turned into a 6 year frame off resto-mod.

07-28-2019, 07:42 PM	#67
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,713	Re: My "new" 1968 c20 Not sure what a nice gate brings . The beds were the same from 67 to I believe 87 so there should be alot of nice ones out there. __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

07-28-2019, 07:43 PM	#68
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,713	Re: My "new" 1968 c20 Sounds good but a road trip to Dallas for a tailgate is a bit much even for me __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

08-06-2019, 09:30 PM	#70
cornerstone Registered User Join Date: Apr 2014 Location: Azle,Texas Posts: 2,248	Re: My "new" 1968 c20 Nice find! Is it a GM piece or repop? Mind if I ask what that set you back? __________________ Brian 1972 C10, "Loyd", LWB to SWB, 5.3, L83/6L80e, 4:11 Tru Trac, Air Ride, VA, DD, 20" Coys, 4 wheel disc, A quick LS swap turned into a 6 year frame off resto-mod.



Register or Log In To remove these advertisements.

08-06-2019, 10:48 PM	#72
cornerstone Registered User Join Date: Apr 2014 Location: Azle,Texas Posts: 2,248	Re: My "new" 1968 c20 Thanks! Can't beat factory metal. __________________ Brian 1972 C10, "Loyd", LWB to SWB, 5.3, L83/6L80e, 4:11 Tru Trac, Air Ride, VA, DD, 20" Coys, 4 wheel disc, A quick LS swap turned into a 6 year frame off resto-mod.

08-08-2019, 01:36 PM	#74
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,713	Re: My "new" 1968 c20 I looked at the Mar-k gate . Only thing that killed it for me was the shipping. They must higher an uber driver to deliver it. But the gate is down to bare metal. Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

Register or Log In To remove these advertisements.