Boyd Welding-67-72 Rear Mount Aluminum Tank

[cpetersen]

Got mine yesterday, looks great Dave. Can't wait to put it in, in a couple of weeks>

[eagleuh1]

Dave, what was the improvement in the gasket seal for the tank? No problems with mine, great tank and nice improvements to an already nice tank. Jim

[Daveboyd]

It has been a while since i have posted. We have been very busy in the shop lately.

We have finally finished the A-1000 version of our 67-72 Tank lineup for you big HP guys. This pump will support 1200+ HP. It is now live on the website.http://www.boydwelding.com/shop/inde...-bed-fill.html

there were a few changes to the structure to make this pump work.

1) We had to add a flat spot in the bottom of the tank so the pump could be mounted correctly
2) We increased the baffling around the pump.
3) we Revised our baffling in all of the tanks to help contain the fuel better

Everything else is the same as all of the other tanks.

Thanks to the Years of support everyone here has given us, We greatly appreciate it.

[Clyde65]

Dave,

I have one question for you, I bought one of your tanks a while ago, I raised my bed floor and would like to have the tank fill at bed level. is there something that I can use that would just fit on the tank and I could put my cap on without cutting or modding the tank any? like a fill extension?

[effects66]

Have had my tank for about 6 months just before the redesign. I just got the chance to finally start my build and install the tank. Great product. Fit like a glove!! top notch.





_____________________

My build thread:

1970 c10 short fleet, 550hp LSX 4l80e, full ridetech
http://www.67-72chevytrucks.com/vboa...d.php?t=556610

[jondancer]

I would like one of these tank but with the filler at the license plate/bumper , I send a pm. Let me know if that's an option.
Thanks
Posted via Mobile Device

[jondancer]

Got my tank, awesome quality! But there's and extra hole on top that I'm not sure what it's for? Is it for a return line?
Posted via Mobile Device

[Pro Performance]

That can be used as a return port or a vent. If you got the tank with a rollover vent, that is where it would go. You can always add the rollover vent there later if you decide. In the meantime you can plug it if you don't want to run a vent or return. It is a NPT thread.

- Travis

[jondancer]

My tank has a roll over vent installed, a sending unit, the fill pipe, and then a plugged hole on top and a plugged hole on the bottom for the fuel out. ....?
Thanks
Posted via Mobile Device

[Pro Performance]

That extra port is for a return line if you want to use it. If not, then you can plug it.

- Travis

[johnnys classics]

Dave, is there still the 10percent discount for list members or a group buy in the near future?

[jondancer]

I tried the 10percent for member discount a few weekd ago, it did not work. The tank is worth every bit of the price though.
Posted via Mobile Device

[johnnys classics]

Thanks Jondancer for that. I had originally bought the metal tank replacement for the blazer, but after seeing so many resonses for the Boyd tank. This probrably will be the way I go also. Maybe I can sell off the blazer set up and recoup some of the purchase price.

[slamed67]

hey dave i just got my stealth efi tank in the mail from you. great work! the welds are superb! looks like a stack of nickles! learned about you on here. pretty good advertisement for ya. thanks a ton!

[johnny's classics]

I orderd a tank for my 66 Chevy truck. Its slated to come on Monday!!!

[Daveboyd]

This product is always evolving. Our website is updated with alot more info and FAQ for these products. here is a link http://www.boydwelding.com/shop/inde...evy-tanks.html

[Sammy]

Anyone have pics of the center bed fill floor with a wood bed installed? Curious as to where the fill spout ends up. Center of bed floor n if it required any additional extension or not. Thanks...

[Daveboyd]

Originally Posted by Sammy

Anyone have pics of the center bed fill floor with a wood bed installed? Curious as to where the fill spout ends up. Center of bed floor n if it required any additional extension or not. Thanks...

I dont currently have any pictures of your request but the fill pipe should fall in the middle of a wood plank and should not require any extension.

You will need a flush access door placed in your bed floor, you would open that door and reach in and remove the cap to direct fill the tank.

[Sammy]

Planning on ordering in about 4 weeks. Any advantage to calling over ordering on line? 67-72 rear center bed fill tank, rollover valve, sender,non EFI, maybe even powder coated if the cost is friendly enough. Thanks

Have you considered making some hinged flush mounted doors with a piano hinge powder coated n raw finish to add to your setup? I would be interested in testing the fit for you..

[SCOOBYDOOBYDOO]

I am looking to get a tank made with the vaporworx system do you guys do that and do you do stainless ??

[Daveboyd]

I am tossing around the idea of doing a Group Buy this month. Anyone Interested?

[Bennett68C10]

Originally Posted by Daveboyd

I am tossing around the idea of doing a Group Buy this month. Anyone Interested?

I'm interested in this, also do you have a top fill tank with the fill mounted closer to the center instead of towards the side of the tank

[mtnbikeman]

I am also interested

[1971_402]

yup..

[1bad396ss]

I'm in for the A1000 67-72 bed fill
Posted via Mobile Device