Project Slo-Go 67 - Page 32 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

RCbowtie69 · 07-26-2010, 05:55 PM

sweet"

NWD02 · 07-26-2010, 06:29 PM

Extremely close. I have everything to finish it. Only thing missing is time...

my67chevytruck · 07-26-2010, 07:38 PM

Quote:

Originally Posted by RCbowtie69

sweet"

Thanks !

Quote:

Originally Posted by NWD02

Extremely close. I have everything to finish it. Only thing missing is time...

I hear ya Nick, but your soo close. What are you lacking?

NWD02 · 07-26-2010, 07:41 PM

Brake lines need to be installed. Rear end needs the spacer kit installed. Front bumper needs to be put on. HAHA. Sooooo close....

my67chevytruck · 07-26-2010, 07:46 PM

Dang bro, wish u were not soo far away, I would help you finish it up

NWD02 · 07-26-2010, 07:50 PM

Thanks... Same to you, if i had the time.

sourkraut · 07-27-2010, 09:42 PM

heath the engine is looking killer!

gcburdic · 07-27-2010, 10:01 PM

Heath....I bought the ground strap kit from Wes....there were 5 straps....here are the 5 spots I tied these grounds to....
1. bed to frame
2. cab to frame
3. passenger inner fender to frame
4. tranny to firewall
5....I cannot remember where I put the dang thing

....sorry!!!!

my67chevytruck · 07-28-2010, 10:04 AM

Quote:

Originally Posted by sourkraut

heath the engine is looking killer!

Thanks John

Quote:

Originally Posted by gcburdic

Heath....I bought the ground strap kit from Wes....there were 5 straps....here are the 5 spots I tied these grounds to....
1. bed to frame
2. cab to frame
3. passenger inner fender to frame
4. tranny to firewall
5....I cannot remember where I put the dang thing

....sorry!!!!

Thanks, we are going to make our own ground straps, I was curious how you mounted the straps to the firewall without damaging the paint (since they need to make contact with the metal). I bought some star washers, and we will be mounting them this weekend. we will most likely ground to the bottom area of the cab support. Thanks

gcburdic · 07-28-2010, 10:51 AM

Heath....I basically used painters blue tape in the area we drilled the hole through the inner fender...seen it done several times....actually just looked again....i went from the tranny bolt to the throttle petal bolt that goes thru the firewall.....(still have the 68 throttle pedal and throttle rod no a throttle cable)

my67chevytruck · 07-28-2010, 03:11 PM

Thans Geoff, we have been using the heck out of the blue painters tapes....

my67chevytruck · 07-29-2010, 08:59 AM

drivers side inner fender installed.

VA72C10 · 07-29-2010, 10:20 AM

Engine bay looks slick! Great job!

**67cheby** · 07-29-2010, 10:23 AM

very nice

my67chevytruck · 07-29-2010, 10:30 AM

Quote:

Originally Posted by VA72C10

Engine bay looks slick! Great job!

Thanks Jonathan!

Quote:

Originally Posted by 67cheby

very nice

Thanks Bro!

sdailey · 07-29-2010, 10:58 AM

Looking good Heath.

BTW, what top radiator hose did you end up using?

es67chevy · 07-29-2010, 12:51 PM

Nice and shiny. Looks, great!

my67chevytruck · 07-29-2010, 09:37 PM

I'll take a another gander and see

Slick67 · 07-29-2010, 10:37 PM

Heath.........that engine bay looks killer!!!! The smoothed firewall is absolutely the way to go....so why didn't you tell me to do it?!?!?!?!

Alan's Classic · 07-29-2010, 10:53 PM

Looks outstanding Heath!!

my67chevytruck · 07-30-2010, 07:12 AM

Quote:

Originally Posted by Slick67

Heath.........that engine bay looks killer!!!! The smoothed firewall is absolutely the way to go....so why didn't you tell me to do it?!?!?!?!

Thanks David, I didn't want to confuse you more by giving you more ideas to toss around .

Quote:

Originally Posted by Alan's Classic

Looks outstanding Heath!!

Thanks Alan!

my67chevytruck · 08-07-2010, 01:42 PM

we have her running a little better now. put seafoam in the oil, and will run her a little longer to clean her up a bit before changing the oil and running mobil 1 synthetic 15w - 50. trying to finish up the dash wiring so i can install the gauge cluster. then we can move on to installing the brake booster etc.

http://s598.photobucket.com/albums/t...enginerun2.mp4

PHAT TONY · 08-07-2010, 10:27 PM

Isn't it cool the way open manifolds sound like it's under water?
NICE WORK; very clean.

my67chevytruck · 08-08-2010, 02:30 PM

Quote:

Originally Posted by PHAT TONY

Isn't it cool the way open manifolds sound like it's under water?
NICE WORK; very clean.

Thanks Tony!, they do sound cool.

Alan's Classic · 08-08-2010, 07:32 PM

She has a heartbeat again. Awesome!! Sounds great

07-26-2010, 05:55 PM	#1
RCbowtie69 Registered User Join Date: Dec 2003 Location: Thomasville, NC Posts: 1,877	Re: Project Slo-Go 67 sweet"

07-26-2010, 06:29 PM	#2
NWD02 Registered User Join Date: Oct 2007 Location: Mont Belvieu, Texas Posts: 729	Re: Project Slo-Go 67 Extremely close. I have everything to finish it. Only thing missing is time...

07-26-2010, 07:41 PM	#4
NWD02 Registered User Join Date: Oct 2007 Location: Mont Belvieu, Texas Posts: 729	Re: Project Slo-Go 67 Brake lines need to be installed. Rear end needs the spacer kit installed. Front bumper needs to be put on. HAHA. Sooooo close....

07-26-2010, 07:46 PM	#5
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: Project Slo-Go 67 Dang bro, wish u were not soo far away, I would help you finish it up __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470

07-26-2010, 07:50 PM	#6
NWD02 Registered User Join Date: Oct 2007 Location: Mont Belvieu, Texas Posts: 729	Re: Project Slo-Go 67 Thanks... Same to you, if i had the time.

07-27-2010, 09:42 PM	#7
sourkraut Registered User Join Date: Sep 2008 Location: WI Posts: 1,243	Re: Project Slo-Go 67 heath the engine is looking killer! __________________ "The way it is" truck build http://67-72chevytrucks.com/vboard/s...d.php?t=359200

07-27-2010, 10:01 PM	#8
gcburdic Restoration Virgin! Join Date: Jan 2008 Location: Huntersville, NC Posts: 8,298	Re: Project Slo-Go 67 Heath....I bought the ground strap kit from Wes....there were 5 straps....here are the 5 spots I tied these grounds to.... 1. bed to frame 2. cab to frame 3. passenger inner fender to frame 4. tranny to firewall 5....I cannot remember where I put the dang thing....sorry!!!! __________________ Geoff with a G 1968 Chevy C10 SWB The Mistress 1972 Custom Deluxe C20 Suburban A Suburban Named Isabella 1966 Ford Mustang Mama's High School Graduation Present

07-28-2010, 10:51 AM	#10
gcburdic Restoration Virgin! Join Date: Jan 2008 Location: Huntersville, NC Posts: 8,298	Re: Project Slo-Go 67 Heath....I basically used painters blue tape in the area we drilled the hole through the inner fender...seen it done several times....actually just looked again....i went from the tranny bolt to the throttle petal bolt that goes thru the firewall.....(still have the 68 throttle pedal and throttle rod no a throttle cable) __________________ Geoff with a G 1968 Chevy C10 SWB The Mistress 1972 Custom Deluxe C20 Suburban A Suburban Named Isabella 1966 Ford Mustang Mama's High School Graduation Present

07-28-2010, 03:11 PM	#11
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: Project Slo-Go 67 Thans Geoff, we have been using the heck out of the blue painters tapes.... __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470

07-29-2010, 08:59 AM	#12
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: Project Slo-Go 67 drivers side inner fender installed. Attached Images __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470

07-29-2010, 10:20 AM	#13
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project Slo-Go 67 Engine bay looks slick! Great job! __________________ Looking for a 67-72 swb or blazer project in or around VA.

07-29-2010, 10:23 AM	#14
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Project Slo-Go 67 very nice __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

07-29-2010, 10:58 AM	#16
sdailey The Few, The Proud Join Date: Jun 2007 Location: Ball Ground, Georgia Posts: 1,830	Re: Project Slo-Go 67 Looking good Heath. BTW, what top radiator hose did you end up using? __________________ Shannon

07-29-2010, 12:51 PM	#17
es67chevy Registered User Join Date: Aug 2007 Location: Bella Vista, AR Posts: 1,107	Re: Project Slo-Go 67 Nice and shiny. Looks, great! __________________ Eric 1967 C10 SWB 383 Stroker/TH400 Brother's One Piece Power Windows Shaved Doors, Markers, and Bumpers 4/6 Early Classic Drop Rear Fuel Tank (49-52 Chevy Car Tank) Surf Blue Paint Bella Vista, AR (Arkansas for those that get the 'A' states mixed up) My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=330869

07-29-2010, 09:37 PM	#18
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: Project Slo-Go 67 I'll take a another gander and see __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470



Register or Log In To remove these advertisements.

07-29-2010, 10:37 PM	#19
Slick67 Sofa King Crazy!! Join Date: Oct 2008 Location: Houston, TX Posts: 3,090	Re: Project Slo-Go 67 Heath.........that engine bay looks killer!!!! The smoothed firewall is absolutely the way to go....so why didn't you tell me to do it?!?!?!?! __________________ You found the Tater. *My Blazer Build (New)* - http://67-72chevytrucks.com/vboard/s...d.php?t=654650 *My 67 Build* - http://67-72chevytrucks.com/vboard/s...d.php?t=335650 67 Chevy LWB big window a/c AKA TOTALLED BY A JACKASS. 1972 2wd Blazer "Porterbuilt and Sloshed"

07-29-2010, 10:53 PM	#20
Alan's Classic 1 thing at a time is progress. Join Date: Jun 2007 Location: Ball Ground GA Posts: 5,511	Re: Project Slo-Go 67 Looks outstanding Heath!! __________________ Alan Philippians 2:14-16 Alan's Classic Facebook page. North Georgia Group Project 1965 Vitamin C-10 1995 GMC Sierra K1500 The "Wrecker"

08-07-2010, 01:42 PM	#22
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: Project Slo-Go 67 we have her running a little better now. put seafoam in the oil, and will run her a little longer to clean her up a bit before changing the oil and running mobil 1 synthetic 15w - 50. trying to finish up the dash wiring so i can install the gauge cluster. then we can move on to installing the brake booster etc. http://s598.photobucket.com/albums/t...enginerun2.mp4 __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470

08-07-2010, 10:27 PM	#23
PHAT TONY Registered User Join Date: Aug 2008 Location: Red Deer ab canada Posts: 1,250	Re: Project Slo-Go 67 Isn't it cool the way open manifolds sound like it's under water? NICE WORK; very clean. __________________ 1972 factory 2 Wheel Drive Blazer-Sold 1972 K10 4X4-Sold 1971 Chevrolet Cheyenne/10-Sold 1970 Chevrolet C/10-Sold 1968 GMC 4X4-Project 1968 Chevrolet C/10 Pro Street 1970 GMC 3/4 Ton-Parts 1997 2WD 2DR Yukon-Sweet http://67-72chevytrucks.com/vboard/s...d.php?t=335664

08-08-2010, 07:32 PM	#25
Alan's Classic 1 thing at a time is progress. Join Date: Jun 2007 Location: Ball Ground GA Posts: 5,511	Re: Project Slo-Go 67 She has a heartbeat again. Awesome!! Sounds great __________________ Alan Philippians 2:14-16 Alan's Classic Facebook page. North Georgia Group Project 1965 Vitamin C-10 1995 GMC Sierra K1500 The "Wrecker"

Register or Log In To remove these advertisements.