|
|
|
02-21-2010, 07:25 PM
|
#1 |
|
#16876
Join Date: Apr 2005
Location: Auburn WA
Posts: 12,266
|
Re: What did you do to your truck today?
It took longer than I thought it would but if it don't leak it's done. I got lucky and did not have to loosen the motor mounts and jack the engine. The pan dropped out cleanly. I used Permatex Right Stuff to place the gaskets and seals on the pan. While it set up I cleaned the block. Had to go to Schucks for a couple items including my missing gasket scraper. I had to improvise because they did not sell scrapers, although they had a hell of a deal on mini bikes, chinese generators and ****ty chrome dress up parts. With a little care the pan went back up without goofing up the gaskets or seals. I opted to put two small bolts in the center on each side first then the rest. I had big trouble getting the four large bolts started on either side of the rubber seals front and back. I finally realized that the seals were not compressed so I tightened a couple center bolts. After using a screwdriver to align the bolt holes I got the last four in. That only took and hour. As per the directions of the sealant I snugged the bolts and am waiting the suggested one hour before I tighten the bolts the rest of the way. There was a lot of sludge in the pan. I ran a magnet around and came out with a split washer on the end. I did not find a bolt though. It did not appear anything was missing from my view underneath. I suppose it could have been dropped through an oil port from above? I guess I'll just forget I saw that? I have a vague memory of dropping and never finding a washer from the timing chain cover. I think I know where it went. It was chrome and did not appear to have been in there very long. The culprit of my leak was the front seal. You can see the twist in it. I'm going to let the sealant cure for 24 hours which means I won't be putting oil back in it today. Next thing will be to bend new brake lines. My '63 is an outdoor project so its all weather permiting.
__________________
Posted via Stationary Device '71 Custom Deluxe C-20 402. '67 Buick Special 455. '49 Plymouth Special Deluxe. "I love that old car smell"  Some people are like Slinkies... not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs. |
|
|
02-21-2010, 07:38 PM
|
#2 |
|
Registered User
Join Date: Mar 2009
Location: Lebanon, Ohio
Posts: 324
|
Re: What did you do to your truck today?
Installed my Porterbuilt suspension, airbags, front steering components and gas tank.
|
|
|
|
02-21-2010, 08:04 PM
|
#3 |
|
Member of the longbed union.
Join Date: Feb 2009
Location: Killeen, Tx
Posts: 2,158
|
Re: What did you do to your truck today?
I cleaned out the garage and cut off the saddles on the diff to mock of my wishbone set up. Sorry dont have pics
__________________
Paul 88 GMC Crew Cab dually, 454/T400 64 LWB 400 HP 350/350T Bagged, under construction! Sold most of it! 92 S10 Iron Duke 5 speed, 5/7 drop for now. soon to be bagged. Sold http://67-72chevytrucks.com/vboard/s...59#post4637759 |
|
|
|
02-21-2010, 08:17 PM
|
#4 |
|
Registered User
Join Date: Nov 2009
Location: Center, MO
Posts: 121
|
Re: What did you do to your truck today?
I cleaned out the garage so I could find my truck project!
__________________
GMCMG 1964 GMC 1/2 ton LWB project - 1982 GMC 6.2 diesel engine/suspension donor - 1966 Chevy 3/4 ton frame/doors/fenders donor - tons of parts - cause you can't build a truck without 4 of everything! 2001 3/4HD Duramax Diesel extended cab lwb4x4 1984 Chevy C30 6.2 diesel lift truck (project) 1962 GMC w/5 lugs, 350/350 auto (was for parts, but couldn't bring myself to do it!) glascock.m@hotmail.com |
|
|
|
02-21-2010, 08:45 PM
|
#5 |
|
Junior Member
Join Date: Dec 2006
Location: Newburgh, IN
Posts: 1,247
|
Re: What did you do to your truck today?
Finished up my shifter. Had the rods on the wrong arms. I had to get my wife out to run it thru the gears while I watched from below. She couldn't figure out why I kept calling her Linda (AKA Vaughn)!
 She didn't find the humor when I explained who Linda Vaughn was/is!
__________________
1966 Chevy C10 Longbed I'm Bob....ol Curt was my Grandpa The truck was his and he sure as heck wouldn't understand why I took a perfectly good truck and tore it down! 
Last edited by ol Curt; 02-21-2010 at 08:45 PM. |
|
|
|
02-21-2010, 10:41 PM
|
#6 |
|
Senior Enthusiast
Join Date: Feb 2007
Location: Spokane Valley, WA
Posts: 8,356
|
Re: What did you do to your truck today?
Ah yes, Miss Golden Shifter!
|
|
|
|
02-21-2010, 11:00 PM
|
#7 |
|
One foot in front of the other
 
Join Date: Aug 2008
Location: Parrottsville, TN
Posts: 5,440
|
Re: What did you do to your truck today?
Added some trim rings-
|
|
|
|
02-22-2010, 02:54 AM
|
#8 | |
|
Registered User
Join Date: Sep 2009
Location: California Delta
Posts: 2,163
|
Re: What did you do to your truck today?
Quote:
__________________
Name: Rich Current Ride: 1964 C-10 Short Fleetside Daily Driver: 2005 GMC crew cab short fleetside /2001 Chevy Tahoe Past GM Trucks: 1959 GMC short stepside 1968 GMC short stepside-4x4 1973 Chevy short stepside 1989 Chevy short fleetside-reg cab 1993 Chevy short fleetside-Xcab 2002 Chevy short fleetside-Xcab Save the dinosaurs, use synthetic oil. |
|
|
|
|
02-22-2010, 01:34 PM
|
#9 |
|
One foot in front of the other
Join Date: Aug 2008
Location: Parrottsville, TN
Posts: 5,440
|
Re: What did you do to your truck today?
3 self tapping screws through the original rally wheel holes into the center cap. Enough room to get to the original lug nuts with an impact as well.
|
|
|
|
02-22-2010, 08:29 PM
|
#10 |
|
Registered User
 
Join Date: Sep 2006
Location: San Francisco
Posts: 4,779
|
Re: What did you do to your truck today?
If all goes by plan. This truck will be cut up into manageable pieces and the good stuff is going to be used on my 66. You know, front disc set up, maybe the rear end, and whatever else I can use. OH yeah. And a big bucket of nuts and bolts.
I was going to sell that engine to someone for cheap, but they never got back to me.. Oh well..
__________________
"A man and his truck, what a beautiful thing" 65 Short Fleetside BBC 65 Long Fleetside 283 3 on the tree for now. my build thread http://www.67-72chevytrucks.com/vboa...d.php?t=259536 |
|
|
|
02-22-2010, 09:35 PM
|
#11 | |
|
Registered User
Join Date: Sep 2009
Location: California Delta
Posts: 2,163
|
Re: What did you do to your truck today?
Quote:
__________________
Name: Rich Current Ride: 1964 C-10 Short Fleetside Daily Driver: 2005 GMC crew cab short fleetside /2001 Chevy Tahoe Past GM Trucks: 1959 GMC short stepside 1968 GMC short stepside-4x4 1973 Chevy short stepside 1989 Chevy short fleetside-reg cab 1993 Chevy short fleetside-Xcab 2002 Chevy short fleetside-Xcab Save the dinosaurs, use synthetic oil. |
|
|
|
|
02-22-2010, 08:33 PM
|
#12 |
|
'67 Chevy C-50
Join Date: Feb 2008
Location: Monticello, IA
Posts: 62
|
Re: What did you do to your truck today?
I looked at mine for a brief second as I pulled my daily driver into the garage next to it. Haha. Its too cold here in Iowa right now and I dont have the privilege of a heated garage.
__________________
Bad Riv '67 C50 Flatbed Dump '98 Z71 Ext. Cab |
|
|
|
02-22-2010, 10:17 PM
|
#13 |
|
Registered User
Join Date: Dec 2009
Location: winnipeg, manitoba
Posts: 46
|
Re: What did you do to your truck today?
Shaved the seams on my dash to pillars.
__________________
1960 Chevy Short Wide Truck(being restored) 1962 Pontiac Parisienne Bagged 1996 Chevy Caprice 9c1 
|
|
|
|
02-25-2010, 07:43 PM
|
#14 |
|
DiablosWeldingFabrication
Join Date: Jun 2009
Location: Elverta ,CA
Posts: 201
|
Re: What did you do to your truck today?
way better look! today i changed my valve covers and air cleaner..what do you guys think? The before and after pic..
|
|
|
|
02-25-2010, 08:45 PM
|
#15 |
|
Registered User
Join Date: Dec 2009
Location: Carolina Coast
Posts: 582
|
Re: What did you do to your truck today?
picked me a up a 64 short stepper project 350 3 speed on the floor....lots of work here
    
Last edited by thunder71; 02-25-2010 at 08:52 PM. |
|
|
|
02-25-2010, 10:46 PM
|
#16 |
|
One foot in front of the other
Join Date: Aug 2008
Location: Parrottsville, TN
Posts: 5,440
|
Re: What did you do to your truck today?
[QUOTE=thunder71;3825197]picked me a up a 64 short stepper project 350 3 speed on the floor....lots of work here
Looks like a good starting point |
|
|
|
02-26-2010, 01:32 AM
|
#17 |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,939
|
Re: What did you do to your truck today?
I cut some of my steel floor up & re-arranged the pieces to make room for a flush fill stainless fuel filler. I posted a cell phone pic in my build thread.
I also dropped/broke my camera  .
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
02-28-2010, 09:17 AM
|
#18 |
|
Registered User
Join Date: Dec 2009
Location: Carolina Coast
Posts: 582
|
Re: What did you do to your truck today?
picked up another rusty bucket 66 short stepper saved from the crusher
    
|
|
|
|
03-01-2010, 10:44 PM
|
#19 |
|
Registered User
Join Date: Dec 2009
Location: Orlando, Florida
Posts: 427
|
Re: What did you do to your truck today?
Used the hood for a table so I could pinstripe my helmet.
|
|
|
|
02-25-2010, 09:52 PM
|
#20 | |
|
Registered User
Join Date: Nov 2008
Location: Elk Grove Ca
Posts: 629
|
Re: What did you do to your truck today?
Quote:
|
|
|
|
|
02-25-2010, 10:24 PM
|
#21 |
|
Justified!
Join Date: Apr 2007
Location: Valencia, Ca
Posts: 1,366
|
Re: What did you do to your truck today?
Cut the front springs on my truck, put on my new rims and tires, and then found out my alternator was bad..........
__________________
Chad 1964 GMC Fleetside Shortbed....350/700R4 tranny 
|
|
|
|
02-26-2010, 09:30 AM
|
#22 |
|
Registered User
Join Date: Feb 2010
Location: so cal
Posts: 436
|
Re: What did you do to your truck today?
watched my truck get burred under the snow AGAIN.I hate nj can't wait to move back to calif.Road trip comming up soon.
__________________
big old burb in primer.lot of work to do. |
|
|
|
02-26-2010, 03:16 PM
|
#23 |
|
Doin' it live!
Join Date: Jan 2010
Location: Eagle Mountain, Utah
Posts: 471
|
Re: What did you do to your truck today?
Got my transmission and carrier shimmed to take care of a wicked vibration at highway speeds. Works great now... minus the uber low gearing in the axle that I need to replace.
__________________
-Panelrodder 1953 GMC Panel truck - 'Curly' 1961 Chevy Suburban - 'Larry' - Sold 2005 Harley Sportster - 'Shemp' |
|
|
|
02-26-2010, 03:21 PM
|
#24 |
|
Registered User
Join Date: Feb 2010
Location: The Dalles Oregon
Posts: 191
|
Re: What did you do to your truck today?
got brake master cylinder installed, licensed and insured and title put in my about to take tuck out of town first time since at least 93 thats what the old plates and tags say
__________________
1966 C-10 long wide- currently with 2 3/4 sectioned crossmember, 3 inch cupped a arms with 2700 bags, 67 master cylinder, in the middle of a v8 swap, soon custom rear wishbone set up and bags 1942 chevy/divco ambulance 1937 chevy truck |
|
|
|
02-27-2010, 01:21 AM
|
#25 |
|
Member of the longbed union.
Join Date: Feb 2009
Location: Killeen, Tx
Posts: 2,158
|
Re: What did you do to your truck today?
I pulled the motor and trans out so I can run my brake and fuel lines.
__________________
Paul 88 GMC Crew Cab dually, 454/T400 64 LWB 400 HP 350/350T Bagged, under construction! Sold most of it! 92 S10 Iron Duke 5 speed, 5/7 drop for now. soon to be bagged. Sold http://67-72chevytrucks.com/vboard/s...59#post4637759 |
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
