What did you do to your truck today! - Page 336 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

colgad · 11-24-2013, 11:51 PM

Painted the tailgate, fitting the bed (in primer) tomorrow so I can drill the wood bed. Then remove and paint and reassemble.

magwakeenercew2jh · 11-24-2013, 11:55 PM

Quote:

Originally Posted by colgad

Painted the tailgate, fitting the bed (in primer) tomorrow so I can drill the wood bed. Then remove and paint and reassemble.

Now THERE's a shop!!!!

colgad · 11-25-2013, 12:00 AM

My camera phone makes it look bigger than it is.

mud.man.rj · 11-25-2013, 12:04 AM

I'm with you Mag, shop looks a lot bigger than mine, nice.

jbassC10 · 11-25-2013, 12:05 AM

In stalled the New LMC tailgate! Painful-for the first time, but with wisdom from the wise on this forum, everything is possible!

Check out my profile and see the success as of now, of the entire front and rear Brake Swap out! 4/6 drop is ordered and in the mail! California to Arkansas!

eagleuh1 · 11-25-2013, 10:55 AM

jbassC10, have you had your truck on the road much. Haven't seen it around Russellville. Thought I'd seen most of them. Nice looking truck. Jim

OregonNed · 11-25-2013, 04:49 PM

I just went out yesterday in the carport and checked the dryer sheets and made sure no vagrant rodents were setting up shop..

VWNate1 · 11-25-2013, 06:19 PM

Remember to change those dryer sheets every month or you'll get an unpleasant surprise....

I just came back from running errands in my stalling out C/10 W/ 250 I6 & TH350 , two footing it through dense L.A. traffic isn't my idea of fun .

I stopped to fill the tank and did a fuel economy check ~G , not bad for an old clapped out pickup truck .

In The Ten Ring · 11-25-2013, 08:16 PM

I removed all the trim (moulding) from the fender I bought from Jeremiah King. (It came off amazingly easy). Then I ran it over to the body shop to fix the UPS damage.

jbassC10 · 11-26-2013, 03:44 AM

Quote:

Originally Posted by eagleuh1

jbassC10, have you had your truck on the road much. Haven't seen it around Russellville. Thought I'd seen most of them. Nice looking truck. Jim

Hey!
Trucks in Conway at a buddies where were close to finishing it up! I'll Possibly have it over here in Russellville a week or so from now getting ready to move home(Yellvile ar). and of course show it to some college buddies!

:-) I hope yours is treating you well!!

eagleuh1 · 11-26-2013, 07:23 AM

Its earning its keep hauling and pulling construction supplies now. Just about finished the new guage console with electric speedo for the 5.3.
http://67-72chevytrucks.com/vboard/a...1&d=1385424976

Andy4639 · 11-26-2013, 10:22 AM

Redid the door panels in my truck a few days ago.

Also installed road kill inside the doors while I had them a part!

PAWS 72 · 11-26-2013, 10:41 AM

Quote:

Originally Posted by Andy4639

Redid the door panels in my truck a few days ago.

Also installed road kill inside the doors while I had them a part!

Tell any difference Andy?

**Razorbacker** · 11-26-2013, 11:52 AM

I got my Aux Battery system working on my longhorn. A big thanks to Roger Koop for the harness, fits and works great. Now I have 12V power at the back of the truck via the camper harness.

lyrikz · 11-26-2013, 12:23 PM

I sold it.

harrydunn · 11-26-2013, 12:44 PM

Replaced my non-functioning AM radio.

magwakeenercew2jh · 11-26-2013, 09:52 PM

Played with glove box stuff while I wait for the new alt.

Nice day. So I was also under the hood cleaning up a little.

In the mail came some faux leather sheeting.

I'm trying to figure out if I want to match the cluster by getting a *real* chrome glove box and covering the center with an insert of this stuff, or just stop all the madness and paint it the color of the dash.

AKChevyman · 11-26-2013, 10:39 PM

I installed the Air tank and compressor on the Frame. Tomorrow I am going to try and mount the Solenoids. Then it is on to Routing the air lines.

bbcmudtruck · 11-26-2013, 11:11 PM

I finally got my c-notch cut and bolted into place. The new bed arrives tomorrow!

vectorit · 11-26-2013, 11:37 PM

Picked up a cherry H052 4.10 ratio 3rd member with it's axle shafts.

Big step forward in getting my burb more highway friendly, by swapping out my 4.57 3rd member for the 4.10's.

heathbirkendahl · 11-27-2013, 01:52 AM

Picked up my bench seat.

heathbirkendahl · 11-27-2013, 01:55 AM

Full pic

magwakeenercew2jh · 11-27-2013, 01:57 AM

heathbirk, that's probably the most beautiful seat I've ever seen.

Bravo!

heathbirkendahl · 11-27-2013, 02:02 AM

Quote:

Originally Posted by magwakeenercew2jh

heathbirk, that's probably the most beautiful seat I've ever seen.

Bravo!

Thank you!

eagleuh1 · 11-27-2013, 07:34 AM

HeathBirkandahl, what did that seat come from? Looks really good.

11-24-2013, 11:51 PM	#8376
colgad Registered User Join Date: Jun 2006 Location: Lutz, Florida Posts: 838	Re: What did you do to your truck today! Painted the tailgate, fitting the bed (in primer) tomorrow so I can drill the wood bed. Then remove and paint and reassemble. Attached Images __________________ 1967 Red, C10 Short Bed 6.0L T5 5 speed 1967 Orange and Black C50 6.2 Detroit Diesel NV4500, 2 Ton Pickup 1972 White, Chevy Blazer 2WD 67 Dog house 5.3 4L65 2016 Power Tour LH 1955 Red-Cream, Chevrolet Nomad, restoration on hold 2004 Black, Corvette Z06 LS6 convertible (Rock solid Fun) 2011/2018 Power Tour Last edited by colgad; 11-24-2013 at 11:54 PM. Reason: Images not correct

11-25-2013, 12:00 AM	#8378
colgad Registered User Join Date: Jun 2006 Location: Lutz, Florida Posts: 838	Re: What did you do to your truck today! My camera phone makes it look bigger than it is. __________________ 1967 Red, C10 Short Bed 6.0L T5 5 speed 1967 Orange and Black C50 6.2 Detroit Diesel NV4500, 2 Ton Pickup 1972 White, Chevy Blazer 2WD 67 Dog house 5.3 4L65 2016 Power Tour LH 1955 Red-Cream, Chevrolet Nomad, restoration on hold 2004 Black, Corvette Z06 LS6 convertible (Rock solid Fun) 2011/2018 Power Tour

11-25-2013, 12:04 AM	#8379
mud.man.rj Registered User Join Date: Dec 2011 Location: Creighton Sask. Canada Posts: 4,121	Re: What did you do to your truck today! I'm with you Mag, shop looks a lot bigger than mine, nice. __________________ 1987 Green n Green machine. 5.0 4spd std. 7" lift w 35's.

11-25-2013, 12:05 AM	#8380
jbassC10 Registered User Join Date: May 2013 Location: Russellville AR Posts: 148	Re: What did you do to your truck today! In stalled the New LMC tailgate! Painful-for the first time, but with wisdom from the wise on this forum, everything is possible! Check out my profile and see the success as of now, of the entire front and rear Brake Swap out! 4/6 drop is ordered and in the mail! California to Arkansas! Attached Images

11-25-2013, 10:55 AM	#8381
eagleuh1 Registered User Join Date: Jul 2009 Location: Russellville, Arkansas Posts: 1,699	Re: What did you do to your truck today! jbassC10, have you had your truck on the road much. Haven't seen it around Russellville. Thought I'd seen most of them. Nice looking truck. Jim

11-25-2013, 04:49 PM	#8382
OregonNed Registered User Join Date: Dec 2012 Location: Vancouver, Washington Posts: 1,644	Re: What did you do to your truck today! I just went out yesterday in the carport and checked the dryer sheets and made sure no vagrant rodents were setting up shop.. __________________ 1968 Chevrolet C/10 LWB - 327, TH350 - 4/5 Drop

11-25-2013, 06:19 PM	#8383
VWNate1 Registered User Join Date: Feb 2012 Location: So. Cali. Posts: 2,655	Re: What did you do to your truck today! Remember to change those dryer sheets every month or you'll get an unpleasant surprise.... I just came back from running errands in my stalling out C/10 W/ 250 I6 & TH350 , two footing it through dense L.A. traffic isn't my idea of fun . I stopped to fill the tank and did a fuel economy check ~G , not bad for an old clapped out pickup truck . __________________ -Nate Geezer '49 3100 235 W/ Muncie SM420 SOLD '69 C/10 shortbed sidemount survivor 250 L6 W/ 350TH

11-25-2013, 08:16 PM	#8384
In The Ten Ring Registered User Join Date: Jun 2013 Location: West Virginia Posts: 6,421	Re: What did you do to your truck today! I removed all the trim (moulding) from the fender I bought from Jeremiah King. (It came off amazingly easy). Then I ran it over to the body shop to fix the UPS damage.

11-26-2013, 07:23 AM	#8386
eagleuh1 Registered User Join Date: Jul 2009 Location: Russellville, Arkansas Posts: 1,699	Re: What did you do to your truck today! Its earning its keep hauling and pulling construction supplies now. Just about finished the new guage console with electric speedo for the 5.3. http://67-72chevytrucks.com/vboard/a...1&d=1385424976

11-26-2013, 10:22 AM	#8387
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,945	Re: What did you do to your truck today! Redid the door panels in my truck a few days ago. Also installed road kill inside the doors while I had them a part! __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

11-26-2013, 11:52 AM	#8389
Razorbacker Senior Member Join Date: Aug 2011 Location: Benton, AR. Posts: 239	Re: What did you do to your truck today! I got my Aux Battery system working on my longhorn. A big thanks to Roger Koop for the harness, fits and works great. Now I have 12V power at the back of the truck via the camper harness. Attached Images

11-26-2013, 12:23 PM	#8390
lyrikz PITbut Join Date: Sep 2007 Location: monroe washington Posts: 3,052	Re: What did you do to your truck today! I sold it. __________________ New project. 1971 Twin Turbo blazer http://67-72chevytrucks.com/vboard/s...d.php?t=676047 My new YOUTUBE channel.. Videos of my truck and a current walk around. Lyrikz74 Youtube channel *DONE! SOLD!* My 1971 stepside build thread My Build Thread UPDATED 6/11. DONE and sold.

11-26-2013, 12:44 PM	#8391
harrydunn Registered User Join Date: Dec 2010 Location: Columbia, MO Posts: 256	Re: What did you do to your truck today! Replaced my non-functioning AM radio. __________________ 1972 GMC 2500 Custom, 96K miles, Purchased New By My Grandparents 2016 Toyota Tundra TRD Off-Road SR5 1993/2003/2005 Toyota Land Cruisers 2004 Corvette Z06 / 2000 Covette Coupe 2006 Ducati Multistrada 2014 BMW X3 XDrive35i M Sport

11-26-2013, 09:52 PM	#8392
magwakeenercew2jh RAT1968 '68 Cab/'71 Parts Join Date: Feb 2002 Location: Coarsegold, CA Posts: 2,375	Re: What did you do to your truck today! Played with glove box stuff while I wait for the new alt. Nice day. So I was also under the hood cleaning up a little. In the mail came some faux leather sheeting. I'm trying to figure out if I want to match the cluster by getting a real chrome glove box and covering the center with an insert of this stuff, or just stop all the madness and paint it the color of the dash. Attached Images __________________ M17 Coarsegold, CA RAT's shiny now. But always a rat.

11-26-2013, 10:39 PM	#8393
AKChevyman Chevy Forever Join Date: Jun 2005 Location: Dalzell SC Posts: 314	Re: What did you do to your truck today! I installed the Air tank and compressor on the Frame. Tomorrow I am going to try and mount the Solenoids. Then it is on to Routing the air lines. __________________ My first love 1971 C20 Hugger orange Getting face lift and heart transplant .30 402 BB /TH400 and GV Wifes car 1969 Chevelle SS 396 325hp/TH400 Factroy A/C Automatic w/ Floor shift console. restored.



Register or Log In To remove these advertisements.

11-26-2013, 11:11 PM	#8394
bbcmudtruck Registered User Join Date: Nov 2012 Location: ravenwood, mo Posts: 709	Re: What did you do to your truck today! I finally got my c-notch cut and bolted into place. The new bed arrives tomorrow!

11-26-2013, 11:37 PM	#8395
vectorit What? Join Date: Jun 2007 Location: Southern California Posts: 7,617	Re: What did you do to your truck today! Picked up a cherry H052 4.10 ratio 3rd member with it's axle shafts. Big step forward in getting my burb more highway friendly, by swapping out my 4.57 3rd member for the 4.10's. Attached Images __________________ Chris 1968 K20 Suburban 1972 K10 LWB PU

11-27-2013, 01:52 AM	#8396
heathbirkendahl Registered User Join Date: Jul 2012 Location: Campbell, CA Posts: 452	Re: What did you do to your truck today! Picked up my bench seat. Attached Images __________________ 1971 C/10 - Orange & White 2009 GMC 1500 - Lowered 3/4 22' KMC Slides

11-27-2013, 01:55 AM	#8397
heathbirkendahl Registered User Join Date: Jul 2012 Location: Campbell, CA Posts: 452	Re: What did you do to your truck today! Full pic Attached Images __________________ 1971 C/10 - Orange & White 2009 GMC 1500 - Lowered 3/4 22' KMC Slides

11-27-2013, 01:57 AM	#8398
magwakeenercew2jh RAT1968 '68 Cab/'71 Parts Join Date: Feb 2002 Location: Coarsegold, CA Posts: 2,375	Re: What did you do to your truck today! heathbirk, that's probably the most beautiful seat I've ever seen. Bravo! __________________ M17 Coarsegold, CA RAT's shiny now. But always a rat.

11-27-2013, 07:34 AM	#8400
eagleuh1 Registered User Join Date: Jul 2009 Location: Russellville, Arkansas Posts: 1,699	Re: What did you do to your truck today! HeathBirkandahl, what did that seat come from? Looks really good.

Register or Log In To remove these advertisements.